Home › Engine / Hybrid System › FA20 (ENGINE CONTROL) › SFI SYSTEM
RM2090E _51 Engine / Hybrid System _060665 FA20 ENGINE CONTROL _0297470 SFI SYSTEM C

FA20 ENGINE CONTROL  SFI SYSTEM  P0122  Throttle Position Sensor Circuit Low Input  P0123  Throttle / Pedal Position Sensor / Switch "A" Circuit High Input  P0222  Throttle / Pedal Position Sensor / Switch "B" Circuit Low Input  P0223  Throttle / Pedal Position Sensor / Switch "B" Circuit High Input  P2135  Throttle / Pedal Position Sensor / Switch "A" / "B" Voltage Correlation  


DESCRIPTION

HINT:

These DTCs relate to the throttle position sensor.


The throttle position sensor is mounted on the throttle with motor body assembly, and detects the opening angle of the throttle valve. This sensor is a non-contact type sensor. It uses Hall-effect elements in order to yield accurate signals even in extreme driving conditions, such as at high speeds as well as very low speeds.

The throttle position sensor has 2 sensor circuits, each of which transmits a signal, VTA1 and VTA2. VTA1 is used to detect the throttle valve angle and VTA2 is used to detect malfunctions in VTA2. The sensor signal voltages vary between 0 V and 5 V in proportion to the throttle valve opening angle, and are transmitted to the VTA1 and VTA2 terminals of the ECM.

As the valve closes, the sensor output voltage decreases and as the valve opens, the sensor output voltage increases. The ECM calculates the throttle valve opening angle according to these signals and controls the throttle actuator in response to driver inputs. These signals are also used in calculations such as air fuel ratio correction, power increase correction and fuel-cut control.

A280064E03
1.531,0.375 1.302,0.375 1.302,0.375 1.01,1.292 true 1.01,1.969 0.635,2.677 true 0.615,0.583 0.719,0.583 0.719,0.583 0.958,1.615 true 2.51,2.823 2.896,3.052 0.385,0.229 10 false ECM 3.698,2.25 4.219,2.625 0.521,0.375 10 false 0.60 3.698,2 4.156,2.292 0.458,0.292 10 false 1.48 3.677,0.99 4.333,1.396 0.656,0.406 10 false 4.70 3.677,0.76 4.198,1.073 0.521,0.313 10 false 5.00 5.813,2.813 6.146,3.104 0.333,0.292 10 false 86 3.99,2.823 4.333,3.104 0.344,0.281 10 false 0 5.01,1.823 5.542,2.208 0.531,0.385 10 false VTA1 4.563,2.76 5.448,2.99 0.885,0.229 10 false Usable Range 4.573,1.438 5.042,1.802 0.469,0.365 10 false VTA2 3.135,0.438 4.865,0.656 1.729,0.219 10 false Sensor Output Voltage (V) 0.188,3.125 1.677,3.333 1.49,0.208 10 false Throttle Position Sensor 5.063,3.208 6.729,3.458 1.667,0.25 10 false Throttle Opening Angle (°) 1.583,0.292 2.458,0.573 0.875,0.281 10 false Magnet 0.469,2.719 1.073,2.938 0.604,0.219 10 false IC No. 2 1.438,1.479 1.969,1.781 0.531,0.302 10 false VTA1 1.438,1.802 1.99,2.094 0.552,0.292 10 false VTA2 1.458,1.135 1.802,1.427 0.344,0.292 10 false VC 1.448,2.135 1.729,2.396 0.281,0.26 10 false E2 0.052,0.51 0.656,0.729 0.604,0.219 10 false IC No. 1

DTC No. DTC Detection Condition Trouble Area
P0122 The voltage of VTA1 is 0.213 V or less for 0.024 seconds or more.
(1 trip detection logic)
·

Throttle position sensor (built into throttle with motor body assembly)

·

Short in VTA1 circuit

·

Open in VC circuit

·

ECM


P0123 The voltage of VTA1 is more than 4.772 V for 0.024 seconds or more.
(1 trip detection logic)
·

Throttle position sensor (built into throttle with motor body assembly)

·

Open in VTA1 circuit

·

Open in E1 circuit

·

Short between VC and VTA1 circuits

·

ECM


P0222 The voltage of VTA2 is 0.213 V or less for 0.024 seconds or more.
(1 trip detection logic)
·

Throttle position sensor (built into throttle with motor body assembly)

·

Short in VTA2 circuit

·

Open in VC circuit

·

ECM


P0223 The voltage of VTA2 is 4.772 V or more for 0.024 seconds or more.
(1 trip detection logic)
·

Throttle position sensor (built into throttle with motor body assembly)

·

Open in VTA2 circuit

·

Open in E1 circuit

·

Short between VC and VTA2 circuits

·

ECM


P2135 Deviation in voltages of VTA1 and VTA2 exceed thresholds for 0.212 seconds or more.
(1 trip detection logic)
·

Short between VTA1 and VTA2 circuits

·

Throttle position sensor (built into throttle with motor body assembly)

·

ECM



HINT:
·

When any of these DTCs are output, check the throttle valve opening angle using the GTS. Enter the following menus: Powertrain / Engine / Data List / Throttle Position No. 1 and Throttle Position No. 2.

·

Throttle Position No. 1 is the VTA1 signal, and Throttle Position No. 2 is the VTA2 signal.

Reference (Normal Condition):
GTS Display Accelerator Pedal Fully Released Accelerator Pedal Fully Depressed
Throttle Position No. 1 0.213 to 0.821 V 3.928 to 4.772 V
Throttle Position No. 2 0.213 to 1.657 V 4.142 to 4.772 V




MONITOR DESCRIPTION

The ECM uses the throttle position sensor to monitor the throttle valve opening angle. There are several checks that the ECM performs to confirm the proper operation of the throttle position sensor.

·

A specific voltage difference is expected between the sensor terminals, VTA1 and VTA2, for each throttle valve opening angle. If the difference between VTA1 and VTA2 is incorrect, the ECM interprets this as a malfunction in the sensor circuit, and stores a DTC.

·

VTA1 and VTA2 each have a specific voltage range. If VTA1 or VTA2 is outside the normal operating range, the ECM interprets this as a malfunction in the sensor circuit, and stores a DTC.

·

VTA1 and VTA2 should never be close to the same voltage level. If VTA1 is within 0.02 V of VTA2, the ECM determines that there is a short circuit in the sensor circuit, and stores a DTC.


If the malfunction is not repaired successfully, a DTC is stored 10 seconds after the engine is next started.

CONFIRMATION DRIVING PATTERN

1.
A283032E17
0.188,0.458 1.146,0.76 0.958,0.302 10 false Engine Speed 0.167,2.521 1.125,2.74 0.958,0.219 10 false Vehicle Speed 0.896,1.75 1.271,2 0.375,0.25 10 false Idling 0.156,1 1.281,1.208 1.125,0.208 10 false 2500 to 3000 rpm 3.198,0.896 3.615,1.25 0.417,0.354 10 false [A] 5.396,2.677 5.771,2.896 0.375,0.219 10 false [B] 0.052,2.885 1.313,3.073 1.26,0.188 10 false 10 km/h (6.25 mph) 0.323,3.469 1.313,3.635 0.99,0.167 10 false 0 km/h (0 mph) 2.656,4.188 4.042,4.365 1.385,0.177 10 false 40 seconds or more 4.969,4.177 6.021,4.385 1.052,0.208 10 false 1 minute or more 6.552,3.99 7.021,4.417 0.469,0.427 10 false Time

2.

Connect the GTS to the DLC3.

3.

Turn the ignition switch to ON and turn the GTS on.

4.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation) (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON and turn the GTS on.

7.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.

8.

With the vehicle stationary, depress the accelerator pedal and maintain an engine speed of between 2500 and 3000 rpm for 40 seconds or more [A].

9.

Drive the vehicle at 10 km/h (6.25 mph) or more for 1 minute or more [B].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


10.

Enter the following menus: Powertrain / Engine / Trouble Codes.

11.

Read pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



12.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

13.

Input the DTC: P0122, P0123, P0222, P0223 or P2135.

14.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.



15.

If the test result is INCOMPLETE or N/A and no DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




FAIL-SAFE

When any of these DTCs or other DTCs relating to Electronic Throttle Control System (ETCS) malfunctions are stored, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle actuator, and the throttle valve is returned to a specified throttle angle by the return spring. The ECM then adjusts the engine output by controlling the fuel injection (intermittent fuel-cut) and ignition timing, in accordance with the accelerator pedal angle, to allow the vehicle to continue at a minimal speed. If the accelerator pedal is depressed firmly and gently, the vehicle can be driven slowly.

Fail-safe mode continues until a pass condition is detected, and the ignition switch is then turned off.

WIRING DIAGRAM

A280063E03
0.885,2.896 3.167,3.281 2.281,0.385 10 false Throttle Position Sensor (Built into Throttle with Motor Body Assembly) 5.76,2.938 6.979,3.656 1.219,0.719 10 false ECM 0.875,2.729 1.313,3.063 0.438,0.333 10 false C15 5.01,1.635 5.26,1.948 0.25,0.313 10 false 28 5,2.229 5.26,2.552 0.26,0.323 10 false 29 5.313,2.302 5.604,2.604 0.292,0.302 10 false E1 5.01,1.094 5.26,1.406 0.25,0.313 10 false 19 5.302,1.198 5.573,1.531 0.271,0.333 10 false VC 5.01,0.563 5.26,0.875 0.25,0.313 10 false 18 5.031,0.042 5.281,0.354 0.25,0.313 10 false 4 5.302,0.656 5.792,0.99 0.49,0.333 10 false VTA1 5.313,0.156 5.646,0.552 0.333,0.396 10 false EC 5.302,1.729 5.823,2.094 0.521,0.365 10 false VTA2 2.865,0.635 3.115,0.948 0.25,0.313 10 false 6 2.865,1.708 3.115,2.021 0.25,0.313 10 false 4 2.875,1.188 3.125,1.5 0.25,0.313 10 false 5 2.865,2.292 3.115,2.604 0.25,0.313 10 false 3 4.958,0.24 5.302,0.542 0.344,0.302 10 false A33 4.958,0.771 5.531,1.156 0.573,0.385 10 false A36 4.958,1.313 5.354,1.604 0.396,0.292 10 false A36 4.958,1.833 5.344,2.104 0.385,0.271 10 false A36 4.958,2.406 5.344,2.667 0.385,0.26 10 false A36 3.573,1.021 3.802,1.271 0.229,0.25 10 false * 4.417,1.031 4.646,1.281 0.229,0.25 10 false * 3.604,2.115 3.833,2.365 0.229,0.25 10 false * 3.521,3.125 4.677,3.583 1.156,0.458 10 false *: Shielded 2.438,0.635 2.906,0.979 0.469,0.344 10 false VTA1 2.563,1.198 2.865,1.5 0.302,0.302 10 false VC 2.427,1.708 3.042,2.104 0.615,0.396 10 false VTA2 2.573,2.292 2.823,2.594 0.25,0.302 10 false E2

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (THROTTLE POSITION SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Throttle Position No. 1 and Throttle Position No. 2.


e.

Read the values displayed on the GTS.

Result
When Accelerator Pedal Released When Accelerator Pedal Depressed Trouble Area Proceed to
Throttle Position No. 1
(VTA1)
Throttle Position No. 2
(VTA2)
Throttle Position No. 1
(VTA1)
Throttle Position No. 2
(VTA2)
0 to 0.213 V 0 to 0.213 V 0 to 0.213 V 0 to 0.213 V VC circuit open A
4.772 to 5.0 V 4.772 to 5.0 V 4.772 to 5.0 V 4.772 to 5.0 V E2 circuit open
0 to 0.213 V,
or 4.772 to 5.0 V
0.213 to 1.657 V 0 to 0.213 V,
or 4.772 to 5.0 V
4.142 to 4.772 V VTA1 circuit open or ground short
0.213 to 0.821 V 0 to 0.213 V,
or 4.772 to 5.0 V
3.928 to 4.772 V 0 to 0.213 V,
or 4.772 to 5.0 V
VTA2 circuit open or ground short
0.213 to 0.821 V 0.213 to 1.657 V 3.928 to 4.772 V 4.142 to 4.772 V Throttle position sensor circuit normal B



A

2.CHECK HARNESS AND CONNECTOR (THROTTLE POSITION SENSOR - ECM)

B

5.CHECK WHETHER DTC OUTPUT RECURS (THROTTLE POSITION SENSOR DTCS)
2.CHECK HARNESS AND CONNECTOR (THROTTLE POSITION SENSOR - ECM)
a.

Disconnect the throttle with motor body assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
A36-19 (VC) - C15-5 (VC) Always Below 1 Ω
A36-18 (VTA1) - C15-6 (VTA1) Always Below 1 Ω
A36-28 (VTA2) - C15-4 (VTA2) Always Below 1 Ω
A36-29 (E1) - C15-3 (E2) Always Below 1 Ω


Standard Resistance (Check for short):
Tester Connection Condition Specified Condition
A36-19(VC) or C15-5 (VC) - Body ground Always 10 kΩ or higher
A36-18 (VTA1) or C15-6 (VTA1) - Body ground Always 10 kΩ or higher
A36-29 (E1) or C15-3 (E2) - Body ground Always 10 kΩ or higher
A36-29 (E1) or C15-4 (VTA2) - Body ground Always 10 kΩ or higher




OK

3.INSPECT ECM (VC VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT ECM (VC VOLTAGE)
a.
U146750E03
1.51,1.271 1.229,1.719 true 2.135,1.271 2.458,1.677 true 0.208,0.583 0.531,0.771 0.323,0.188 10 false C15 0.115,0.083 0.479,0.281 0.365,0.198 10 false *a 1.042,1.729 1.323,1.906 0.281,0.177 10 false E2 2.49,1.698 2.771,1.875 0.281,0.177 10 false VC

Disconnect the throttle with motor body assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C15-5 (VC) - C15-3 (E2) Ignition switch ON 4.5 to 5.5 V


Text in Illustration
*a Front view of wire harness connector
(to Throttle with Motor Body Assembly)



OK

4.REPLACE THROTTLE WITH MOTOR BODY ASSEMBLY

NG

4.REPLACE THROTTLE WITH MOTOR BODY ASSEMBLY
a.

Replace the throttle with motor body assembly (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>THROTTLE BODY>REMOVAL).



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS (THROTTLE POSITION SENSOR DTCS)
5.CHECK WHETHER DTC OUTPUT RECURS (THROTTLE POSITION SENSOR DTCS)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.



e.

Start the engine.


f.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Read DTCs.

Result
Result Proceed to
DTC P0122, P0123, P0222, P0223 and/or P2135 are output A
DTC is not output B



A

B

END