Home › Engine / Hybrid System › FA20 (ENGINE CONTROL) › SFI SYSTEM › 2012.03–2016.06
RM2090E _51 Engine / Hybrid System _060665 FA20 ENGINE CONTROL _0297470 SFI SYSTEM C

FA20 ENGINE CONTROL  SFI SYSTEM  P0191  Fuel Rail Pressure Sensor Circuit Range / Performance  P0192  Fuel Rail Pressure Sensor Circuit Low Input  P0193  Fuel Rail Pressure Sensor Circuit High Input  


DESCRIPTION

The fuel pressure sensor is installed on the delivery pipe. The sensor changes fuel pressure to an electrical signal and sends the signal to the ECM. Then the ECM controls the pump discharge using this feedback to maintain the fuel's target pressure. If the sensor output stops, the ECM will stop the high pressure side fuel pump and supply fuel using the low pressure side fuel pump.

DTC No. DTC Detection Condition Trouble Area
P0191 One of the following conditions is met (2 trip detection logic):
·

Fuel pressure is 1.9 MPa or more 5 hours or more after ignition switch turned off.

·

Fuel pressure is 1.84 MPa or less for 10 seconds or more with engine running when 5 hours or more elapsed after ignition switch turned off.


·

Open or short in fuel pressure sensor circuit

·

Fuel pressure sensor

·

ECM


P0192 Fuel pressure sensor voltage is too low for 2.5 seconds or more.
(1 trip detection logic)
·

Short in fuel pressure sensor circuit

·

Fuel pressure sensor

·

ECM


P0193 Fuel pressure sensor voltage is too high for 2.5 seconds or more.
(1 trip detection logic)
·

Open in fuel pressure sensor circuit

·

Fuel pressure sensor

·

ECM



HINT:

After confirming DTC P0192 or P0193, use the GTS to confirm the fuel pressure in the delivery pipe by entering the following menus: Powertrain / Engine / Data List / Fuel Press.


Fuel Pressure (kPa) Malfunction
Approximately 0
·

PR and/or E1 circuit short


Approximately 26000
·

PR and/or VC circuit short



MONITOR DESCRIPTION

These DTCs are set if the fuel pressure sensor output voltage is out of the standard range. The DTCs stand for an open or short malfunction of the sensor circuit.

If these DTCs are set, the ECM enters fail-safe mode and limits the engine power. Fail-safe mode continues until the ignition switch is turned off.

CONFIRMATION DRIVING PATTERN

P0191
1.
A397513E01
0.188,0.115 1.198,0.323 1.01,0.208 10 false Vehicle Speed 1.781,0.375 3.01,0.563 1.229,0.188 10 false Ignition switch OFF 3.49,0.365 4.646,0.573 1.156,0.208 10 false Ignition switch ON 0.271,1.688 1.208,1.865 0.938,0.177 10 false 0 km/h (0 mph) 0.469,1.115 1.208,1.51 0.74,0.396 10 false 30 km/h (18.75 mph) 3.438,2.375 4.667,2.563 1.229,0.188 10 false 5 hours or more 1.833,2.375 3.063,2.563 1.229,0.188 10 false 1 minutes or more 5.042,2.375 6.271,2.563 1.229,0.188 10 false 1 minutes or more 6.365,2.188 6.74,2.396 0.375,0.208 10 false Time 2.167,0.958 2.542,1.167 0.375,0.208 10 false [A] 3.833,1.542 4.208,1.75 0.375,0.208 10 false [B] 5.448,0.938 5.823,1.146 0.375,0.208 10 false [C]

2.

Connect the GTS to the DLC3.

3.

Turn the ignition switch to ON and turn the GTS on.

4.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation) (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON.

7.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.

8.

With the vehicle stationary, depress the accelerator pedal and maintain an engine speed of between 2500 and 3000 rpm for 40 seconds or more.

9.

Drive the vehicle at 30 km/h (18.75 mph) or more for 1 minute or more [A].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


10.

Turn the ignition switch off and leave vehicle for 5 hours or more [B].

11.

Turn the ignition switch to ON and turn the GTS on.

12.

Enter the following menus: Powertrain / Engine / Trouble Codes.

13.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.

14.

Drive the vehicle at 30 km/h (18.75 mph) or more for 1 minute or more [C].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


15.

Read pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



16.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

17.

Input the DTC: P0191.

18.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.



19.

If the test result is INCOMPLETE or N/A and no DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.





P0192, P0193
1.
A283032E17
0.188,0.458 1.146,0.76 0.958,0.302 10 false Engine Speed 0.167,2.521 1.125,2.74 0.958,0.219 10 false Vehicle Speed 0.896,1.75 1.271,2 0.375,0.25 10 false Idling 0.156,1 1.281,1.208 1.125,0.208 10 false 2500 to 3000 rpm 3.198,0.896 3.615,1.25 0.417,0.354 10 false [A] 5.396,2.677 5.771,2.896 0.375,0.219 10 false [B] 0.052,2.885 1.313,3.073 1.26,0.188 10 false 10 km/h (6.25 mph) 0.323,3.469 1.313,3.635 0.99,0.167 10 false 0 km/h (0 mph) 2.656,4.188 4.042,4.365 1.385,0.177 10 false 40 seconds or more 4.969,4.177 6.021,4.385 1.052,0.208 10 false 1 minute or more 6.552,3.99 7.021,4.417 0.469,0.427 10 false Time

2.

Connect the GTS to the DLC3.

3.

Turn the ignition switch to ON and turn the GTS on.

4.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation) (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON and turn the GTS on.

7.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.

8.

With the vehicle stationary, depress the accelerator pedal and maintain an engine speed of between 2500 and 3000 rpm for 40 seconds or more [A].

9.

Drive the vehicle at 10 km/h (6.25 mph) or more for 1 minute or more [B].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


10.

Enter the following menus: Powertrain / Engine / Trouble Codes.

11.

Read pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



12.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

13.

Input the DTC: P0192 or P0193.

14.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.



15.

If the test result is INCOMPLETE or N/A and no DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.





WIRING DIAGRAM

A280065E03
2.49,1.271 2.813,1.646 0.323,0.375 10 false 3 1.365,2.656 2.875,2.917 1.51,0.26 10 false Fuel Pressure Sensor 5.25,2.802 5.635,3.063 0.385,0.26 10 false ECM 1.365,2.49 1.813,2.76 0.448,0.271 10 false C10 4.521,0.729 4.906,1.021 0.385,0.292 10 false A36 4.563,0.552 4.927,0.906 0.365,0.354 10 false 19 4.875,1.292 5.208,1.656 0.333,0.365 10 false PR 4.521,1.396 4.927,1.719 0.406,0.323 10 false A34 4.604,1.219 4.854,1.531 0.25,0.313 10 false 9 4.521,2.115 4.896,2.406 0.375,0.292 10 false A36 4.563,1.927 4.813,2.24 0.25,0.313 10 false 29 2.49,0.604 2.74,0.917 0.25,0.313 10 false 1 2.49,1.979 2.802,2.333 0.313,0.354 10 false 2 4.875,2 5.115,2.375 0.24,0.375 10 false E1 2.177,0.604 2.479,0.927 0.302,0.323 10 false VC 4.875,0.615 5.313,0.99 0.438,0.375 10 false VC 2.177,1.271 2.479,1.667 0.302,0.396 10 false PR 2.198,1.979 2.427,2.292 0.229,0.313 10 false E2

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (FUEL PRESS)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Fuel Press.


e.

Read the values.

Result:
Fuel Pressure (kPa) Proceed to
26000 or more A
Approximately 0
3000 to 5000* B


HINT:

*: The value must change when the engine is moving or stationary.




A

2.INSPECT FUEL PRESSURE SENSOR (FUEL PRESSURE SENSOR POWER SOURCE)

B

2.INSPECT FUEL PRESSURE SENSOR (FUEL PRESSURE SENSOR POWER SOURCE)
a.
U146751E03
1.375,1.281 1.125,1.708 true 0.521,0.958 0.813,1.146 0.292,0.188 10 false C10 0.115,0.104 0.479,0.302 0.365,0.198 10 false *a 0.885,1.74 1.177,1.927 0.292,0.188 10 false VC

Disconnect the fuel pressure sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C10-1 (VC) - Body ground Ignition switch ON 4.5 to 5.5 V


Text in Illustration
*a Front view of wire harness connector
(to Fuel Pressure Sensor)



OK

3.INSPECT ECM (PR VOLTAGE)

NG

5.CHECK HARNESS AND CONNECTOR (ECM - FUEL PRESSURE SENSOR)
3.INSPECT ECM (PR VOLTAGE)
a.
U146768E06
2.156,1.021 2.438,1.719 true 0.865,1.146 1.031,1.719 true 2.01,0.281 2.302,0.469 0.292,0.188 10 false A34 2.417,1.75 3.104,1.938 0.688,0.188 10 false 9 (PR) 0.594,0.281 0.885,0.469 0.292,0.188 10 false A36 1,1.76 1.76,1.948 0.76,0.188 10 false 29 (E1) 0.094,0.083 0.344,0.271 0.25,0.188 10 false *a

Start the engine.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A34-9 (PR) - A36-29 (E1) Idling with warm engine 1.0 to 1.7 V


Text in Illustration
*a Component with harness connected
(ECM)


HINT:

The fuel pressure in the delivery pipe is 3 to 5 MPa.



OK

NG

4.CHECK HARNESS AND CONNECTOR (ECM - FUEL PRESSURE SENSOR)
4.CHECK HARNESS AND CONNECTOR (ECM - FUEL PRESSURE SENSOR)
a.

Disconnect the ECM connectors.


b.

Disconnect the fuel pressure sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
A34-9 (PR) - C10-3 (PR) Always Below 1 Ω
A36-29 (E1) - C10-2 (E2) Always Below 1 Ω


Standard Resistance (Check for short):
Tester Connection Condition Specified Condition
A34-9 (PR) or C10-3 (PR) - body ground Always 10 kΩ or higher
A34-29 (E1) or C10-2 (E2) - body ground Always 10 kΩ or higher




OK

REPLACE FUEL PRESSURE SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - FUEL PRESSURE SENSOR)

5.CHECK HARNESS AND CONNECTOR (ECM - FUEL PRESSURE SENSOR)
a.

Disconnect the fuel pressure sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
A36-19 (VC) - C10-1 (VC) Always Below 1 Ω


Standard Resistance (Check for short):
Tester Connection Condition Specified Condition
A36-19 (VC) or C10-1 (VC) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - FUEL PRESSURE SENSOR)