Home › Engine / Hybrid System › FA20 (ENGINE CONTROL) › SFI SYSTEM
RM2090E _51 Engine / Hybrid System _060665 FA20 ENGINE CONTROL _0297470 SFI SYSTEM C

FA20 ENGINE CONTROL  SFI SYSTEM  P2122  Throttle / Pedal Position Sensor / Switch "D" Circuit Low Input  P2123  Throttle / Pedal Position Sensor / Switch "D" Circuit High Input  P2127  Throttle / Pedal Position Sensor / Switch "E" Circuit Low Input  P2128  Throttle / Pedal Position Sensor / Switch "E" Circuit High Input  P2138  Throttle / Pedal Position Sensor / Switch "D" / "E" Voltage Correlation  


DESCRIPTION

HINT:
·

These DTCs relate to the accelerator pedal sensor assembly.

·

This electronic throttle control system does not use a throttle cable.



The accelerator pedal sensor assembly is mounted on the accelerator pedal bracket and has 2 sensor circuits: VPA (main) and VPA2 (sub). This sensor is a non-contact type. It uses Hall-effect elements in order to yield accurate signals, even in extreme conditions. The voltage, which is applied to terminals VPA and VPA2 of the ECM, varies between 0 V and 5 V in proportion to the operating angle of the accelerator pedal (throttle valve). A signal from VPA indicates the actual accelerator pedal operating angle (throttle valve opening angle) and is used for engine control. A signal from VPA2 conveys the status of the VPA circuit and is used to check the accelerator pedal sensor assembly itself.

The ECM monitors the actual accelerator pedal operating angle (throttle valve opening angle) through the signals from VPA and VPA2, and controls the throttle actuator according to these signals.

HINT:

The accelerator pedal position output voltages of VPA and VPA2 are almost the same.


A280078E04
0.969,1.969 0.677,2.698 true 1.115,2.292 1.333,2.875 true 0.948,1.719 1.292,0.625 1.292,0.625 1.333,0.625 true 0.979,1.406 0.927,0.552 0.927,0.552 0.844,0.552 true 4.333,1.135 4.073,0.396 4.073,0.396 3.99,0.396 false 6.083,2.458 6.188,3.031 false 4.094,2.146 4.365,2.323 0.271,0.177 10 false 0.7 4.094,1.292 4.365,1.469 0.271,0.177 10 false 4.6 5.583,2.76 6.167,2.99 0.583,0.229 10 false 15.4° 4.094,1.542 4.365,1.719 0.271,0.177 10 false 3.1 2.323,0.292 4.229,0.656 1.906,0.365 10 false Accelerator Pedal Position Output Voltage (V) 2.094,1.208 2.646,1.385 0.552,0.177 10 false EPA 2.094,0.896 2.594,1.073 0.5,0.177 10 false VPA 2.094,1.521 2.656,1.698 0.563,0.177 10 false VCPA 2.094,2.135 2.646,2.313 0.552,0.177 10 false EPA2 2.094,1.813 2.604,1.99 0.51,0.177 10 false VPA2 2.094,2.458 2.656,2.635 0.563,0.177 10 false VCP2 0.344,0.448 1.135,0.625 0.792,0.177 10 false Magnet 1.26,2.927 2.052,3.104 0.792,0.177 10 false Magnet 1.375,0.531 2.021,0.708 0.646,0.177 10 false IC No. 1 0.406,2.75 1.198,2.927 0.792,0.177 10 false IC No. 2 4.688,1.656 5.198,1.833 0.51,0.177 10 false VPA 5.094,1.927 5.573,2.104 0.479,0.177 10 false VPA2 4.302,2.771 4.573,2.948 0.271,0.177 10 false 0 4.594,2.76 5.552,2.938 0.958,0.177 10 false Usable Range 4.344,3.094 6.948,3.375 2.604,0.281 10 false Accelerator Pedal Turning Angle(°) 4.292,0.677 4.563,0.854 0.271,0.177 10 false *a 5.615,0.677 5.885,0.854 0.271,0.177 10 false *b

Text in Illustration
*a Accelerator pedal fully released *b Accelerator pedal fully depressed
- - - -

DTC No. DTC Detection Condition Trouble Area
P2122 VPA voltage is less than 0.213 V.
(1 trip detection logic)
·

Open or short in accelerator pedal sensor circuit

·

Accelerator pedal sensor assembly

·

ECM


P2123 VPA voltage is 4.737 V or more.
(1 trip detection logic)
P2127 VPA2 voltage is less than 0.213 V.
(1 trip detection logic)
P2128 VPA2 voltage is 4.737 V or more.
(1 trip detection logic)
P2138 Difference in the signals from VPA and VPA2 exceeds the threshold.
(1 trip detection logic)

MONITOR DESCRIPTION

The accelerator pedal position sensor is mounted on the accelerator pedal bracket. The accelerator pedal position sensor has 2 sensor elements and 2 signal outputs: VPA and VPA2.When the difference between the output voltages of VPA and VPA2 deviates from the standard, the ECM determines that the accelerator pedal position sensor is malfunctioning. The ECM turns on the MIL and stores the DTC.

CONFIRMATION DRIVING PATTERN

1.
A283035E07
3.958,0.854 4.26,1.073 0.302,0.219 10 false [A] 3.51,2.344 4.833,2.688 1.323,0.344 10 false 1 minute or more 0.313,1.073 1.063,1.469 0.75,0.396 10 false 10 km/h (6.25 mph) 0.479,1.688 1.031,2.063 0.552,0.375 10 false 0 km/h (0 mph) 0.125,0.115 1.167,0.385 1.042,0.271 10 false Vehicle Speed

2.

Connect the GTS to the DLC3.

3.

Turn the ignition switch to ON and turn the GTS on.

4.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation) (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON and turn the GTS on.

7.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.

8.

Depress the accelerator pedal fully and release the accelerator pedal.

9.

Drive the vehicle at 10 km/h (6.25 mph) or more for 1 minute or more [A].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


10.

Enter the following menus: Powertrain / Engine / Trouble Codes.

11.

Read pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



12.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

13.

Input the DTC: P2122, P2123, P2127, P2128 or P2138.

14.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.



15.

If the test result is INCOMPLETE or N/A and no DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




FAIL-SAFE

The accelerator pedal position sensor has 2 (main and sub) sensor circuits. If a malfunction occurs in either of the sensor circuits, the ECM detects the abnormal signal voltage difference between the 2 sensor circuits and switches to fail-safe mode. In fail-safe mode, the functioning circuit is used to calculate the accelerator pedal opening angle to allow the vehicle to continue driving. If both circuits malfunction, the ECM regards the opening angle of the accelerator pedal as being fully closed. In this case, the throttle valve remains closed as if the engine is idling.

If a pass condition is detected and then the ignition switch is turned off, the fail-safe operation stops and the system returns to normal.

WIRING DIAGRAM

A280079E04
1.792,0.719 2.042,1.031 0.25,0.313 10 false 6 0.646,3.729 2.021,4.24 1.375,0.51 10 false Accelerator Pedal Position Sensor 5.177,0.729 5.688,1.031 0.51,0.302 10 false VPA 5.646,3.688 6.063,3.906 0.417,0.219 10 false ECM 0.646,3.563 0.99,3.74 0.344,0.177 10 false A23 4.938,0.729 5.188,1.042 0.25,0.313 10 false 23 5.177,1.167 5.708,1.469 0.531,0.302 10 false EPA 1.792,1.656 2.042,1.969 0.25,0.313 10 false 4 1.792,1.167 2.042,1.479 0.25,0.313 10 false 5 5.177,1.667 5.729,1.969 0.552,0.302 10 false VCPA 1.792,2.115 2.042,2.427 0.25,0.313 10 false 3 5.177,3.688 5.448,3.865 0.271,0.177 10 false A35 1.802,3.052 2.052,3.365 0.25,0.313 10 false 1 1.802,2.563 2.052,2.875 0.25,0.313 10 false 2 5.177,2.125 5.667,2.427 0.49,0.302 10 false VPA2 5.177,2.573 5.698,2.875 0.521,0.302 10 false EPA2 5.177,3.063 5.719,3.365 0.542,0.302 10 false VCP2 4.938,1.177 5.188,1.49 0.25,0.313 10 false 29 4.938,1.667 5.188,1.979 0.25,0.313 10 false 21 4.938,2.125 5.188,2.438 0.25,0.313 10 false 31 4.938,2.573 5.188,2.885 0.25,0.313 10 false 30 4.938,3.063 5.188,3.375 0.25,0.313 10 false 22 3.771,0.563 4.677,0.885 0.906,0.323 10 false Shielded 1.302,0.844 1.698,1.083 0.396,0.24 10 false VPA1 1.313,2.229 1.708,2.469 0.396,0.24 10 false VPA2 1.292,1.271 1.75,1.51 0.458,0.24 10 false GND1 1.302,2.708 1.719,2.948 0.417,0.24 10 false GND2 1.396,1.76 1.792,2 0.396,0.24 10 false VC1 1.396,3.188 1.792,3.427 0.396,0.24 10 false VC2

CAUTION / NOTICE / HINT

HINT:
·

This DTC relates to the accelerator pedal position sensor.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING GTS (ACCELERATOR PEDAL POSITION SENSOR)
A208621E02
0.67,1.751 0.875,1.925 0.205,0.174 10 *a 2.612,1.751 2.803,1.925 0.191,0.174 10 *b

a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Accel Sensor Out No. 1 and Accel Sensor Out No. 2.


e.

Read the values displayed on the GTS.

Text in Illustration
*a Depressed
*b Released

Standard Voltage:
Accelerator Pedal Operation Accel Sensor Out No. 1 Accel Sensor Out No. 2 Difference between Accel Sensor Out No. 1 and Accel Sensor Out No. 2
Released 0.213 to 4.737 V 0.213 to 4.737 V Less than 10%
Depressed 0.213 to 4.737 V 0.213 to 4.737 V


Result
Result Proceed to
NG A
OK B



A

2.CHECK HARNESS AND CONNECTOR (ECM - ACCELERATOR PEDAL SENSOR)

B

2.CHECK HARNESS AND CONNECTOR (ECM - ACCELERATOR PEDAL SENSOR)
a.

Disconnect the ECM connector.


b.

Disconnect the accelerator pedal sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
A35-23 (VPA) - A23-6 (VPA1) Always Below 1 Ω
A35-29 (EPA) - A23-5 (GND1) Always Below 1 Ω
A35-21 (VCPA) - A23-4 (VC1) Always Below 1 Ω
A35-31 (VPA2) - A23-3 (VPA2) Always Below 1 Ω
A35-30 (EPA2) - A23-2 (GND2) Always Below 1 Ω
A35-22 (VCP2) - A23-1 (VC2) Always Below 1 Ω


Standard Resistance (Check for short):
Tester Connection Condition Specified Condition
A35-23 (VPA) or A23-6 (VPA1) - Body ground Always 10 kΩ or higher
A35-29 (EPA) or A23-5 (GND1) - Body ground Always 10 kΩ or higher
A35-21 (VCPA) or A23-4 (VC1) - Body ground Always 10 kΩ or higher
A35-31 (VPA2) or A23-3 (VPA2) - Body ground Always 10 kΩ or higher
A35-30 (EPA2) or A23-2 (GND2) - Body ground Always 10 kΩ or higher
A35-22 (VCP2) or A23-1 (VC2) - Body ground Always 10 kΩ or higher




OK

3.INSPECT ECM (VC VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT ECM (VC VOLTAGE)
a.
U146760E03
1.063,1.177 0.615,1.771 true 1.438,1.219 1.281,1.771 true 1.99,1.208 1.969,1.781 true 2.302,1.208 2.677,1.792 true 0.25,1.063 0.542,1.25 0.292,0.188 10 false A23 0.125,0.115 0.375,0.302 0.25,0.188 10 false *a 1.073,1.813 1.552,2.021 0.479,0.208 10 false GND2 2.531,1.823 3.01,2.031 0.479,0.208 10 false GND1 0.438,1.813 0.802,2.021 0.365,0.208 10 false VC2 1.833,1.813 2.198,2.021 0.365,0.208 10 false VC1

Disconnect the accelerator pedal sensor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A23-4 (VC1) - A23-5 (GND1) Ignition Switch ON 4.5 to 5.5 V
A23-1 (VC2) - A23-2 (GND2) Ignition Switch ON 4.5 to 5.5 V


Text in Illustration
*a Front view of wire harness connector
(to Accelerator Pedal Sensor)



OK

4.REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY

NG

4.REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY
a.

Replace the accelerator pedal sensor assembly (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>ACCELERATOR PEDAL>REMOVAL).



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS (DTC P2122, P2123, P2127, P2128 OR P2138)
5.CHECK WHETHER DTC OUTPUT RECURS (DTC P2122, P2123, P2127, P2128 OR P2138)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.



e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON and turn the GTS on.


g.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


h.

Enter the following menus: Powertrain / Engine / Trouble Codes.


i.

Read DTCs.

Result
Result Proceed to
DTC is not output A
DTC P2122, P2123, P2127, P2128, and/or P2138 is output B



A

END

B