Home › Engine / Hybrid System › FA20 (ENGINE CONTROL) › SFI SYSTEM
RM2090E _51 Engine / Hybrid System _060665 FA20 ENGINE CONTROL _0297470 SFI SYSTEM C

FA20 ENGINE CONTROL  SFI SYSTEM  P0087  Fuel Rail / System Pressure - Too Low  


DESCRIPTION

The high-pressure fuel system consists of the spill control valve, pump plunger and fuel pressure sensor. The spill control valve opens and closes the low-pressure fuel line (from the fuel tank), the pump plunger (operated by the camshaft) pressurizes fuel and the fuel pressure sensor located on the fuel delivery pipe monitors fuel pressure.

The fuel pump for high pressure is installed to the cylinder head cover (bank 2) and is driven by the cam located at the intake camshaft.

The plunger moves up and down by the camshaft rotations, and produces a vacuum to suck fuel and pressurizes the fuel. This fuel flows into the fuel delivery pipe. The ECM opens and closes the spill control valve to regulate the fuel pressure to the target fuel pressure. In order to obtain and maintain the target pressure, the ECM monitors the fuel pressure using the fuel pressure sensor and performs the feedback control.

HINT:

The spill control valve, pump plunger are built into the fuel pump assembly for high pressure.


DTC No. DTC Detection Condition Trouble Area
P0087 Fuel pressure is lower than the target value for 10 seconds or more.
(1 trip detection logic)
·

Leak of fuel

·

Fuel pipe (Fuel tank - Fuel pump assembly (for high pressure) [bank 1 or bank 2])

·

Fuel pipe (Fuel pump assembly (for high pressure) - Fuel injector assembly [for direct injection])

·

Fuel injector assembly (for direct injection)

·

Fuel pump assembly (for high pressure)

·

Injector driver (EDU)

·

Fuel pump assembly

·

ECM



MONITOR DESCRIPTION

If the fuel pressure decreases even after the ECM commands the high-pressure fuel pump to close the spill control valve, a DTC is output.

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Record the Freeze Frame Data.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure) (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON and turn the GTS on.

7.

Based on engine speed, engine load and other freeze frame data stored in the ECM, reproduce the conditions present when the DTC was stored.

8.

Enter the following menus: Powertrain / Engine / Trouble Codes.

9.

Read the DTC.

HINT:
·

If a DTC is output, the system is malfunctioning.

·

If a DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

11.

Input the DTC: P0087.

12.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit



HINT:
·

If the judgment result shown ABNORMAL, the system has a malfunction.

·

If the judgment result shows NORMAL, the system is normal.



13.

If the test result is INCOMPLETE or N/A and no DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.


PROCEDURE

1.CHECK FUEL LEAK (HIGH PRESSURE SIDE)
a.

Check around and beneath the car for fuel leaks, fumes, etc.

OK:

No fuel leaks present.




OK

2.CHECK OTHER DTCS OUTPUT (IN ADDITION TO DTC P0087)

NG

REPAIR OR REPLACE FUEL LEAK POINT

2.CHECK OTHER DTCS OUTPUT (IN ADDITION TO DTC P0087)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.


d.

Read the DTCs.

Result:
Result Proceed to
DTC P0087 is output A
DTC P0087 and other DTCs are output B



HINT:

If any DTCs other than P0087 are output, troubleshoot those DTCs first.



A

3.CHECK IF VEHICLE HAS RUN OUT OF FUEL IN PAST

B

3.CHECK IF VEHICLE HAS RUN OUT OF FUEL IN PAST
a.

Has the vehicle run out of fuel in the past?



YES

DTC CAUSED BY RUNNING OUT OF FUEL

NO

4.READ VALUE USING GTS (FUEL PRESS)
4.READ VALUE USING GTS (FUEL PRESS)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Start the engine.


d.

Enter the following menus: Powertrain / Engine / Data List / Fuel Press.


e.

Read Fuel Press when racing the engine.

Result:
Result Proceed to
Fuel Press value varies. A
Fuel Press value does not increase. B
Fuel Press value does not vary. C




A

5.PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP / SPEED)

B

7.CHECK FUEL LEAK (HIGH PRESSURE SIDE)

C

REPLACE FUEL PRESSURE SENSOR

5.PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP / SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Start the engine.


d.

Enter the following menus: Powertrain / Engine / Active Test / Control the Fuel Pump / Speed.


e.

When performing the Active Test, check for an operating sound from the fuel pump.



OK

6.CHECK FUEL PRESSURE (LOW PRESSURE SIDE)

NG

6.CHECK FUEL PRESSURE (LOW PRESSURE SIDE)
a.

Check the fuel pressure (low pressure side) (See page Engine / Hybrid System>FA20 FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION).



OK

7.CHECK FUEL LEAK (HIGH PRESSURE SIDE)

NG

REPLACE FUEL PRESSURE REGULATOR

7.CHECK FUEL LEAK (HIGH PRESSURE SIDE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Data List / Fuel Press.


d.

Check changes in the fuel pressure when the engine is stopped.

HINT:

Turn the ignition switch to ON immediately after turning the ignition switch off.


A150325E11
1.521,1 2.49,1.167 0.969,0.167 10 false Ignition Switch 1.542,1.385 2.51,1.552 0.969,0.167 10 false Engine Speed 1.563,1.865 2.531,2.031 0.969,0.167 10 false Fuel Pressure 5.354,1.198 5.781,1.385 0.427,0.188 10 false OFF 5.365,1.563 5.792,1.75 0.427,0.188 10 false 0 5.26,2.125 5.688,2.313 0.427,0.188 10 false OK 4.531,2.917 4.958,3.104 0.427,0.188 10 false NG

Result
Result Proceed to
The fuel pressure drops immediately after turning the ignition switch off. A
The fuel pressure is nearly maintained, or with moderate variations. B



A

8.INSPECT FUEL PUMP ASSEMBLY (FOR HIGH PRESSURE)

B

9.REPLACE INJECTOR DRIVER (EDU)
8.INSPECT FUEL PUMP ASSEMBLY (FOR HIGH PRESSURE)
a.

Inspect the fuel pump assembly (for high pressure) (See page Engine / Hybrid System>FA20 FUEL>FUEL PUMP(for High Pressure)>INSPECTION).



OK

9.REPLACE INJECTOR DRIVER (EDU)

NG

REPLACE FUEL PUMP ASSEMBLY (FOR HIGH PRESSURE)

9.REPLACE INJECTOR DRIVER (EDU)
a.

Replace the fuel injector driver (EDU) (See page Engine / Hybrid System>FA20 FUEL>INJECTOR DRIVER>REMOVAL).



NEXT

10.PERFORM CONFIRMATION DRIVING PATTERN
10.PERFORM CONFIRMATION DRIVING PATTERN
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.



e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON and turn the GTS on.


g.

Start the engine and warm it up.


h.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine / Trouble Codes.


j.

Read the DTC.

Result:
Result Proceed to
DTC P0087 is output A
DTC is not output B




A

11.REPLACE FUEL PUMP ASSEMBLY (FOR HIGH PRESSURE)

B

END

11.REPLACE FUEL PUMP ASSEMBLY (FOR HIGH PRESSURE)
a.

Replace the fuel pump assembly (high pressure side) (See page Engine / Hybrid System>FA20 FUEL>FUEL PUMP(for High Pressure)>REMOVAL).

HINT:

If the fuel pump assembly (for high pressure) has been replaced in step 8, then proceed to step 13 without replacing the fuel pump assembly (for high pressure).




NEXT

12.PERFORM CONFIRMATION DRIVING PATTERN
12.PERFORM CONFIRMATION DRIVING PATTERN
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.



e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON and turn the GTS on.


g.

Start the engine and warm it up.


h.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine / Trouble Codes.


j.

Read the DTC.

Result:
Result Proceed to
DTC P0087 is output A
DTC is not output B




A

13.CHECK FUEL LEAK (HIGH PRESSURE SIDE)

B

END

13.CHECK FUEL LEAK (HIGH PRESSURE SIDE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Data List / Fuel Press.


d.

Check changes in the fuel pressure when the engine is stopped.

HINT:

Turn the ignition switch to ON immediately after turning the ignition switch off.


A150325E11
1.521,1 2.49,1.167 0.969,0.167 10 false Ignition Switch 1.542,1.385 2.51,1.552 0.969,0.167 10 false Engine Speed 1.563,1.865 2.531,2.031 0.969,0.167 10 false Fuel Pressure 5.354,1.198 5.781,1.385 0.427,0.188 10 false OFF 5.365,1.563 5.792,1.75 0.427,0.188 10 false 0 5.26,2.125 5.688,2.313 0.427,0.188 10 false OK 4.531,2.917 4.958,3.104 0.427,0.188 10 false NG

Result
Result Proceed to
The fuel pressure drops immediately after turning the ignition off. A
The fuel pressure is nearly maintained, or with moderate variations. B



A

B

REPLACE FUEL INJECTOR ASSEMBLY (FOR DIRECT INJECTION)