Home › Engine / Hybrid System › FA20 (ENGINE CONTROL) › SFI SYSTEM
RM2090E _51 Engine / Hybrid System _060665 FA20 ENGINE CONTROL _0297470 SFI SYSTEM C

FA20 ENGINE CONTROL  SFI SYSTEM  P0088  Fuel Rail / System Pressure - Too High  


DESCRIPTION

Refer to DTC P0087 (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>P0087).

DTC No. DTC Detection Condition Trouble Area
P0088 Fuel pressure is higher than the target value for 10 seconds or more.
(1 trip detection logic)
·

Fuel pump assembly (for high pressure)

·

ECM



MONITOR DESCRIPTION

If the fuel pressure does not decrease even after the ECM commands the high-pressure fuel pump to open the spill control valve, a DTC is output.

If there is minimal difference between the fuel pressure before and after the fuel relief valve operates, a DTC is output.

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Record the Freeze Frame Data.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure) (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON and turn the GTS on.

7.

Based on engine speed, engine load and other freeze frame data stored in the ECM, reproduce the conditions present when the DTC was stored.

8.

Enter the following menus: Powertrain / Engine / Trouble Codes.

9.

Read the DTC.

HINT:
·

If a DTC is output, the system is malfunctioning.

·

If a DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

11.

Input the DTC: P0088.

12.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit



HINT:
·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows NORMAL, the system is normal.



13.

If the test result is INCOMPLETE or N/A and no DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.


PROCEDURE

1.CHECK OTHER DTCS OUTPUT (IN ADDITION TO DTC P0088)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.


d.

Read the DTCs.

Result:
Result Proceed to
DTC P0088 is output A
DTC P0088 and other DTCs are output B



HINT:

If any DTCs other than P0088 are output, troubleshoot those DTCs first.



A

2.PERFORM ACTIVE TEST USING GTS

B

2.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Active Test / Control the Target Fuel Pressure / Fuel Press.


d.

Check that the fuel pressure fluctuates when the target fuel pressure changes.

HINT:

The Active Test operation lowers the target fuel pressure by 12.5% or increase the target fuel pressure by 24.8%.


OK:

Fuel pressure fluctuates.




OK

3.REPLACE FUEL PUMP ASSEMBLY (FOR HIGH PRESSURE)

NG

REPLACE FUEL PRESSURE SENSOR

3.REPLACE FUEL PUMP ASSEMBLY (FOR HIGH PRESSURE)
a.

Replace the fuel pump assembly (for high pressure) (See page Engine / Hybrid System>FA20 FUEL>FUEL PUMP(for High Pressure)>REMOVAL).



NEXT

4.CHECK IF DTC OUTPUT RECURS (SEE IF DTC P0088 IS OUTPUT AGAIN)
4.CHECK IF DTC OUTPUT RECURS (SEE IF DTC P0088 IS OUTPUT AGAIN)
a.

Connect the GTS to the DLC3.


b.

Turn the GTS on.



d.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


e.

Enter the following menus: Powertrain / Engine / Trouble Codes.


f.

Read the DTCs.

Result:
Result Proceed to
DTC P0088 is output A
DTC is not output B




A

B

END