Home › Engine / Hybrid System › FA20 (ENGINE CONTROL) › SFI SYSTEM › 2012.03–2013.07
RM2090E _51 Engine / Hybrid System _060665 FA20 ENGINE CONTROL _0297470 SFI SYSTEM C

FA20 ENGINE CONTROL  SFI SYSTEM  P0196  Engine Oil Temperature Sensor (Range/Performance)  P0197  Engine Oil Temperature Sensor Low  P0198  Engine Oil Temperature Sensor High  


DESCRIPTION

The resistance of the thermistor within the oil temperature sensor changes in accordance with variations in the oil temperature. The method for connecting the oil temperature sensor and the ECM is the same as for the intake air temperature sensor.

HINT:

If any DTC is stored, the ECM enters fail-safe mode. During operation of fail-safe mode, the ECM sets the engine oil temperature determined value at 70°C (158°F). Operation of fail-safe mode continues until the ECM restores normal operation.


DTC No. DTC Detection Condition Trouble Area
P0196 Despite estimated engine oil temperature is higher than 45°C (113°F), engine oil temperature sensor value is lower than 45°C (113°F).
(2 trip detection logic)
·

Engine oil temperature sensor

·

ECM


P0197 Engine oil temperature sensor voltage is less than 0.203 V for 0.5 seconds or more.
(1 trip detection logic)
P0198 Engine oil temperature sensor voltage is more than 4.698 V for 0.5 seconds or more.
(1 trip detection logic)

MONITOR DESCRIPTION

P0196

When a cold engine start is performed and then the engine is warmed up, if the Engine oil temperature sensor value is less than specified value, it is determined that a malfunction has occurred. If this is detected in 2 consecutive driving cycles, the ECM interprets this as a malfunction in the engine oil temperature sensor and stores a DTC.


P0197, P0198

The ECM monitors the sensor voltage and uses this value to calculate the engine oil temperature. When the sensor output voltage deviates from the normal operating range, the ECM interprets this as a malfunction in the engine oil temperature sensor circuit and stores a DTC.


CONFIRMATION DRIVING PATTERN

1.
A283032E17
0.188,0.458 1.146,0.76 0.958,0.302 10 false Engine Speed 0.167,2.521 1.125,2.74 0.958,0.219 10 false Vehicle Speed 0.896,1.75 1.271,2 0.375,0.25 10 false Idling 0.156,1 1.281,1.208 1.125,0.208 10 false 2500 to 3000 rpm 3.198,0.896 3.615,1.25 0.417,0.354 10 false [A] 5.396,2.677 5.771,2.896 0.375,0.219 10 false [B] 0.052,2.885 1.313,3.073 1.26,0.188 10 false 10 km/h (6.25 mph) 0.323,3.469 1.313,3.635 0.99,0.167 10 false 0 km/h (0 mph) 2.656,4.188 4.042,4.365 1.385,0.177 10 false 40 seconds or more 4.969,4.177 6.021,4.385 1.052,0.208 10 false 1 minute or more 6.552,3.99 7.021,4.417 0.469,0.427 10 false Time

2.

Connect the GTS to the DLC3.

3.

Turn the ignition switch to ON and turn the GTS on.

4.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation) (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON and turn the GTS on.

7.

Start the engine and warm it up until the engine oil temperature reaches 75°C (167°F) or higher.

8.

With the vehicle stationary, depress the accelerator pedal and maintain an engine speed of between 2500 and 3000 rpm for 40 seconds or more [A].

9.

Drive the vehicle at 10 km/h (6.25 mph) or more for 1 minute or more [B].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


10.

Enter the following menus: Powertrain / Engine / Trouble Codes.

11.

Read pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



12.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

13.

Input the DTC: P0196, P0197 or P0198.

14.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.



15.

If the test result is INCOMPLETE or N/A and no DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




WIRING DIAGRAM

A280062E11
0.875,2.823 3.26,3.417 2.385,0.594 10 false Engine Oil Temperature Sensor 5.781,2.813 6.281,3.063 0.5,0.25 10 false ECM 0.875,2.667 1.375,2.927 0.5,0.26 10 false C21 5.063,1.26 5.406,1.604 0.344,0.344 10 false 20 5.063,1.99 5.385,2.313 0.323,0.323 10 false 29 2.875,1.979 3.25,2.365 0.375,0.385 10 false 1 2.885,1.271 3.146,1.604 0.26,0.333 10 false 2 5.333,2.813 5.792,3.104 0.458,0.292 10 false A36 2.594,1.281 2.938,1.646 0.344,0.365 10 false OT 5.313,1.271 5.677,1.625 0.365,0.354 10 false OT 5.313,2 5.646,2.344 0.333,0.344 10 false E1 2.594,1.979 2.938,2.302 0.344,0.323 10 false E2

CAUTION / NOTICE / HINT

HINT:
·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

When the DTC is output, check the engine oil temperature using the GTS. Enter the following menus: Powertrain / Engine / Data List / Engine Oil Temperature. If the Engine Oil Temperature value is lower than the actual engine oil temperature, the engine oil temperature sensor circuit may be malfunctioning. In this case, check the wire harnesses and connectors (and those connections) between the ECM and the engine oil temperature sensor first.



PROCEDURE

1.READ VALUE USING GTS (ENGINE OIL TEMPERATURE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Engine Oil Temperature.


e.

Read the value displayed on the GTS.

Result
Result Proceed to
-40°C (-40°F) A
215°C (419°F) B
Between 75 and 100°C (167 and 212°F) C

HINT:
·

If there is an open circuit, the GTS indicates -40°C (-40°F).

·

If there is a short circuit, the GTS indicates higher than 215°C (419°F).





A

2.READ VALUE USING GTS (ENGINE OIL TEMPERATURE)

B

4.READ VALUE USING GTS (ENGINE OIL TEMPERATURE)

C

2.READ VALUE USING GTS (ENGINE OIL TEMPERATURE)
a.
U190110E02
1.74,2.833 1.438,3.042 true 2.104,2.833 2.438,3.031 true 0.385,1.927 0.635,2.115 0.25,0.188 10 false *a 0.958,1.323 1.208,1.51 0.25,0.188 10 false *1 2.76,1.344 3.01,1.531 0.25,0.188 10 false *2 2.438,0.406 2.75,0.594 0.313,0.188 10 false OT 2.438,0.781 2.708,0.969 0.271,0.188 10 false E1 0.927,2.667 1.208,2.833 0.281,0.167 10 false C21 1.229,3.042 1.51,3.208 0.281,0.167 10 false E2 2.479,3.031 2.76,3.198 0.281,0.167 10 false OT

Disconnect the Engine oil temperature sensor connector.


b.

Connect terminals 1 and 2 of the Engine oil temperature sensor connector on the wire harness side.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine / Data List / Engine Oil Temperature.


g.

Read the value displayed on the GTS.

Standard value:

215°C (419°F)


Text in Illustration
*1 Engine oil temperature sensor
*2 ECM
*a Front view of wire harness connector
(to Engine oil temperature sensor)



OK

NG

3.CHECK HARNESS AND CONNECTOR (ECM - ENGINE OIL TEMPERATURE SENSOR)
3.CHECK HARNESS AND CONNECTOR (ECM - ENGINE OIL TEMPERATURE SENSOR)
a.

Disconnect the engine oil temperature sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
A36-20 (OT) - C21-2 (OT) Always Below 1 Ω
A36-29 (E1) - C21-1 (E2) Always Below 1 Ω




OK

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR

4.READ VALUE USING GTS (ENGINE OIL TEMPERATURE)
a.
A280086E09
0.781,1.479 1.031,1.667 0.25,0.188 10 false *1 2.573,1.479 2.823,1.667 0.25,0.188 10 false *2 2.219,0.583 2.552,0.771 0.333,0.188 10 false OT 2.24,0.948 2.521,1.135 0.281,0.188 10 false E1

Disconnect the Engine oil temperature sensor connector.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine / Data List / Engine Oil Temperature.


f.

Read the value displayed on the GTS.

Standard Value:

-40°C (-40°F)


Text in Illustration
*1 Engine oil temperature sensor
*2 ECM



OK

NG

5.CHECK HARNESS AND CONNECTOR (ECM - ENGINE OIL TEMPERATURE SENSOR)
5.CHECK HARNESS AND CONNECTOR (ECM - ENGINE OIL TEMPERATURE SENSOR)
a.

Disconnect the engine oil temperature sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for short):
Tester Connection Condition Specified Condition
A36-20 (OT) or C21-2 (OT) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR