Home › Engine / Hybrid System › FA20 (ENGINE CONTROL) › SFI SYSTEM
RM2090E _51 Engine / Hybrid System _060665 FA20 ENGINE CONTROL _0297470 SFI SYSTEM C

FA20 ENGINE CONTROL  SFI SYSTEM  P0700  Transmission Control System (MIL Request)  


DESCRIPTION

The ECM and TCM communicate with each other via the CAN communication line. If the TCM detects an automatic transmission malfunction, the ECM receives this signal.

DTC No. DTC Detection Condition Trouble Area
P0700 Automatic transmission system malfunction received from the TCM
(1 trip detection logic)
·

Automatic transmission system

·

ECM



WIRING DIAGRAM

A280187E10
4.969,1.677 5.594,2.125 0.625,0.448 10 false CANH 4.958,0.865 5.458,1.167 0.5,0.302 10 false CANL 5.448,2.521 5.802,2.76 0.354,0.24 10 false ECM 4.958,2.521 5.281,2.76 0.323,0.24 10 false A33 4.698,1.542 4.948,1.854 0.25,0.313 10 false 19 4.698,0.708 4.948,1.021 0.25,0.313 10 false 18 2.552,0.719 2.802,1.031 0.25,0.313 10 false 28 2.552,1.542 2.802,1.854 0.25,0.313 10 false 29 2.052,1.698 2.583,2.063 0.531,0.365 10 false CANH 2.052,0.885 2.552,1.188 0.5,0.302 10 false CANL 1.875,2.563 2.281,2.781 0.406,0.219 10 false TCM 1.427,2.563 1.938,2.927 0.51,0.365 10 false A18 0.729,3.302 2.75,3.563 2.021,0.26 10 false : CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:

After turning ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK DTC OUTPUT (AUTOMATIC TRANSMISSION SYSTEM)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / ECT / Trouble Codes.


e.

Read DTCs.

Result
Result Proceed to
DTC is not output A
DTC is output B



A

2.READ OUTPUT DTC

B

2.READ OUTPUT DTC
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.



e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine / Trouble Codes.


i.

Read DTCs.

Result
Result Proceed to
DTC is not output A
DTC P0700 is output B



A

B