Home › Engine / Hybrid System › FA20 (ENGINE CONTROL) › SFI SYSTEM › from 2014.05
RM2090E _51 Engine / Hybrid System _060665 FA20 ENGINE CONTROL _0297470 SFI SYSTEM C

FA20 ENGINE CONTROL  SFI SYSTEM  P2270  Oxygen Sensor Signal Stuck Lean (Bank 1 Sensor 2)  P2271  Oxygen Sensor Signal Stuck Rich (Bank 1 Sensor 2)  


DESCRIPTION

Refer to DTC P0137 (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>P0137).

DTC No. DTC Detection Condition Trouble Area
P2270 Heated oxygen sensor voltage is less than 0.55 V for 15 seconds or more.
(2 trip detection logic)
·

Open or short in heated oxygen sensor circuit

·

Heated oxygen sensor

·

ECM


P2271 Heated oxygen sensor voltage is more than 0.15 V for 0.5 seconds or more.
(2 trip detection logic)

MONITOR DESCRIPTION

This DTC is stored when stuck at lean or stuck at rich state of the heated oxygen sensor is detected.

CONFIRMATION DRIVING PATTERN

A280657E07
1.365,2.406 1.667,2.406 1.667,2.406 1.813,2.271 false 3.396,2.271 3.927,2.448 3.927,2.448 4.417,2.281 false 2.365,2.479 2.51,2.281 false 5.448,2.479 5.313,2.281 false 0.135,0.125 1.083,0.531 0.948,0.406 10 false Vehicle Speed 0.51,0.688 1.052,1.104 0.542,0.417 10 false 97 km/h (60 mph) 0.51,1.229 1.052,1.646 0.542,0.417 10 false 64 km/h (40 mph) 0.573,1.708 1.052,2.125 0.479,0.417 10 false 0 km/h (0 mph) 1.74,1.573 2.198,1.875 0.458,0.302 10 false [A] 2.302,1.021 2.76,1.313 0.458,0.292 10 false [B] 3.177,0.5 3.708,0.813 0.531,0.313 10 false [C] 4,0.906 4.427,1.219 0.427,0.313 10 false [D] 4.563,1.083 5.042,1.385 0.479,0.302 10 false [E] 5.042,0.906 5.594,1.281 0.552,0.375 10 false [F] 6.01,1.052 6.458,1.344 0.448,0.292 10 false [G] 0.104,2.313 1.375,2.49 1.271,0.177 10 false 10 seconds or more 1.854,2.51 3.052,2.677 1.198,0.167 10 false Within 20 seconds 3.406,2.458 4.667,2.625 1.26,0.167 10 false 20 seconds or more 5.427,2.51 6.677,2.708 1.25,0.198 10 false Within 10 seconds 6.375,2.24 6.865,2.469 0.49,0.229 10 false Time

1.

Connect the Techstream to the DLC3.

2.

Turn the ignition switch to ON and turn the Techstream on.

3.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation) (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the Techstream on.

6.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.

7.

Perform the following the confirmation driving pattern.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


(a)

Idle the engine for 10 seconds or more [A].

(b)

Accelerate the vehicle to 97 km/h (60 mph) or more within 20 seconds [B].

(c)

Drive the vehicle at 97 km/h (60 mph) or more for 20 seconds or more [C].

(d)

Release the accelerator pedal to Decelerate until the vehicle speed decreases to less than 64 km/h (40 mph) [D].

HINT:

Release the accelerator pedal fully to perform the fuel-cut.


(e)

Drive the vehicle at 60 km/h (40 mph) or less for 20 seconds or more [E].

(f)

Accelerate the vehicle to 97 km/h (60 mph) or more within 10 seconds [F].

(g)

Release the accelerator pedal and stop the vehicle [G].


8.

Enter the following menus: Powertrain / Engine / Trouble Codes.

9.

Read pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

11.

Input the DTC: P2270 or P2271.

12.

Check the DTC judgment result.

Techstream Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.



13.

If the test result is INCOMPLETE or N/A and no DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.


e.

Read DTCs.


Result
Result Proceed to
P2270 or P2271 is output A
P2270 or P2271 and other DTCs are output B

HINT:

If any DTCs other than P2270 or P2271 are output, troubleshoot those DTCs first.



A

2.CHECK CONNECTOR (HEATED OXYGEN SENSOR)

B

2.CHECK CONNECTOR (HEATED OXYGEN SENSOR)
a.

Disconnect the heated oxygen sensor connector and intermediate connector.


b.

Check for water intrusion into each connector.


OK:

There is no water intrusion.



OK

3.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)

NG

REMOVE WATER FROM THE CONNECTORS COMPLETELY

3.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)
a.

Disconnect the heated oxygen sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.


Standard Resistance (Check for open)
Tester Connection Condition Specified Condition
C13-1 (HT1B) - A36-6 (HT1B) Always Below 1 Ω
C13-3 (OX1B) - A34-21 (OX1B) Always Below 1 Ω

Standard Resistance (Check for short)
Tester Connection Condition Specified Condition
C13-1 (HT1B) or A36-6 (HT1B) - Body ground Always 10 kΩ or higher
C13-3 (OX1B) or A34-21 (OX1B) - Body ground Always 10 kΩ or higher


OK

4.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)
a.

Disconnect the heated oxygen sensor connector.


b.

Reconnect the ECM connector.


c.

Measure the voltage according to the value(s) in the table below.


Standard Voltage
Tester Connection Switch Condition Specified Condition
C13-3 (OX1B) - Body ground Ignition switch ON Below 1.5 V


OK

5.CHECK FOR EXHAUST GAS LEAK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK FOR EXHAUST GAS LEAK
a.

Inspect for exhaust gas leaks from the exhaust manifold sub-assembly and exhaust pipes.


OK:

No gas leakage.



OK

6.REPLACE HEATED OXYGEN SENSOR

NG

REPAIR OR REPLACE EXHAUST GAS LEAK POINT

6.REPLACE HEATED OXYGEN SENSOR
a.


NEXT

7.CHECK WHETHER DTC OUTPUT RECURS
7.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.



e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the Techstream on.


h.

Start the engine and warm it up.


i.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


j.

Enter the following menus: Powertrain / Engine / Trouble Codes.


Result
Result Proceed to
DTC is not output A
DTC P2270 or P2271 is output B


A

END

B