Based upon a signal from the TCM, the combination of shift solenoid valve (S1, S2, S3, S4, SR, SL1, SL2) changes the gear position from 1st to 6th. As a fail-safe function if the solenoid valve system is open or shorted, the TCM cuts power to all solenoids, leaving just the mechanical hydraulic circuit, requiring manual shifting.
| DTC No. | DTC Detection Condition
1.
Diagnosis Condition 2.
Malfunction Status 3.
Malfunction Time 4.
Other |
Trouble Area |
|---|---|---|
| P0985 | 1.
Not learning control prohibited status 2.
During shift solenoid valve SR on signal is output, the TCM's SR output monitor value is "off". 3.
Continues for 500ms or more. 4.
1-trip detection logic |
·
Shift solenoid valve SR ·
Transmission wire ·
Harness and connector ·
TCM |
| P0986 | 1.
Not learning control prohibited status 2.
During shift solenoid valve SR off signal is output, the TCM's SR output monitor value is "on". 3.
Continues for 500ms or more. 4.
1-trip detection logic |
·
Shift solenoid valve SR ·
Transmission wire ·
Harness and connector ·
TCM |
These DTCs indicate an open or short in the shift solenoid valve SR circuit. When there is an open or short circuit in any shift solenoid valve circuit, the TCM detects the problem and illuminates the MIL and stores the DTC.
Perform the universal trip to clear permanent DTCs (See page Drivetrain>TX6A (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM>DTC CHECK / CLEAR).
The shift solenoid valve SR is turned on/off normally when the shift lever is in the D position:
| TCM command gearshift | 1st | 2nd | 3rd | 4th | 5th | 6th |
| Shift solenoid valve SR | ON | ON | ON | ON | OFF | OFF |
Disconnect the TCM connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A18-15(SR) - Body ground | Ignition switch ON | Below 1 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A18-15(SR) - Body ground | 20°C(68°F) | 11 to 15 Ω |
Connect the TCM connector.
OK
NG
Replace the TCM (See page Drivetrain>TX6A (AUTOMATIC TRANSMISSION / TRANSAXLE)>TCM>REMOVAL).
NEXT
(See pageDrivetrain>TX6A (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM>INITIALIZATION)
Disconnect the A18 TCM connector.
Disconnect the L4 transmission wire connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L4-6(SR) - Body ground | Ignition switch ON | Below 1 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L4-6(SR) - A18-15(SR) | Always | Below 1 Ω |
| L4-6(SR) and A18-15(SR) - Body ground | Always | 10 kΩ or higher |
Connect the A18 TCM connector.
Connect the L4 transmission wire connector.
OK
NG
Remove the shift solenoid valve SR (See page Drivetrain>TX6A (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>REMOVAL).
Perform inspection of the shift solenoid valve SR (See page Drivetrain>TX6A (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>INSPECTION).
OK
NG