Home › Drivetrain › TX6A (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM
RM2090E _52 Drivetrain _060674 TX6A AUTOMATIC TRANSMISSION / TRANSAXLE _0297556 AUTOMATIC TRANSMISSION SYSTEM C

TX6A AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  P0751  Shift Solenoid "A" Performance (Shift Solenoid Valve S1)  P0752  Shift Solenoid "A" Stuck ON (S1 Solenoid)  


SYSTEM DESCRIPTION

The TCM carries out detection of the gear position based upon signals from the input speed sensor NT and the output speed sensor SP2. Subsequently, if the gear position as detected by the TCM is different to the commanded gear position, then a related solenoid valve, valve body, or automatic transmission mechanical problem is detected.

DTC No. DTC Detection Condition
1.

Diagnosis Condition

2.

Malfunction Status

3.

Malfunction Time

4.

Other


Trouble Area
P0751
1.

While driving with the shift lever in D, the ATF temperature 20°C (68°F) or more, and coolant temperature 40°C (104°F) or more. (However, abnormalities with the shift solenoid valve S1, S2, S3, S4, SR, SL1, SL2, SLT), input speed sensor NT, output speed sensor SP2, park/neutral position switch, CAN bus, ECM communication, coolant temperature sensor, air flow sensor, electronically control throttle, and accelerator pedal sensor are not detected)

2.

The following conditions are met:

(a)

When the TCM commands shifting to 5th, the actual gear position is also switched to 5th.

(b)

When the TCM commands shifting to 6th gear, the engine overruns (in neutral)


3.

-

4.

2-trip detection logic


·

Shift solenoid valve S1

·

Harness or connector

·

Transmission wire

·

TCM


P0752
1.

While driving with the shift lever in D, the ATF temperature 20°C (68°F) or more, and coolant temperature 40°C (104°F) or more. (However, abnormalities with the shift solenoid valve S1, S2, S3, S4, SR, SL1, SL2, SLT), input speed sensor NT, output speed sensor SP2, park/neutral position switch, CAN bus, ECM communication, coolant temperature sensor, air flow sensor, electronically control throttle, and accelerator pedal sensor are not detected)

2.

The following conditions are met:

(a)

- During driving with the shaft lever in D, when the TCM commands shifting to 1st gear, the actual gear position is shifted to 2nd.

(b)

- When the TCM commands shifting to 5th gear, the actual gear position is also shifted to 5th


3.

-

4.

2-trip detection logic


·

Shift solenoid valve S1

·

Harness or connector

·

Transmission wire

·

TCM



HINT:
·

Gear positions in the event of a solenoid valve mechanical problem:

TCM command gearshift 1st 2nd 3rd 4th 5th 6th
*1: Actual gear position under S1 stuck ON malfunction 2nd 2nd ↑ ↑ ↑ ↑
*2: Actual gear position under S1 stuck OFF malfunction 1st 2nd ↑ ↑ ↑ N*

N*: Neutral

·

Gear position during fail-safe operation:

If any malfunction is detected, the TCM changes into the fail-safe mode to shift into the gear positions as shown in the table below.

Gear position under normal conditions 1st 2nd 3rd 4th 5th 6th
*1: Actual gear position under fail safe mode when S1 stuck ON malfunction 2nd 2nd ↑ ↑ ↑ ↑
*2: Actual gear position under fail safe mode when S1 stuck OFF malfunction 1st*3 2nd*3 ↑ 3rd 3rd 3rd

*3: Under engine braking downshifting to 1st or 2nd gear is prohibited.



MONITOR DESCRIPTION

This DTC indicates "stuck ON malfunction" or "stuck OFF malfunction" of the shift solenoid valve S1.

The TCM commands gear shifts by turning the shift solenoid valves "ON/OFF". When the gear position commanded by the TCM and the actual gear position are not the same, the TCM illuminates the MIL and stores the DTC.

WIRING DIAGRAM

C368964E06
1,1.594 2.5,1.781 1.5,0.188 10 false Shift Solenoid Valve S1 0.667,2.854 2.167,3.042 1.5,0.188 10 false Transmission Wire 0.688,2.688 0.865,2.854 0.177,0.167 10 false L4 2.531,0.729 3.333,1.01 0.802,0.281 10 false S1 2.771,0.729 2.948,0.896 0.177,0.167 10 false 8 5.521,0.75 5.698,0.917 0.177,0.167 10 false 7 5.729,0.969 6.625,1.646 0.896,0.677 10 false S1 5.979,2.938 6.25,3.135 0.271,0.198 10 false A18 5.969,3.094 6.313,3.302 0.344,0.208 10 false TCM

CAUTION / NOTICE / HINT

NOTICE:

Perform the universal trip to clear permanent DTCs (See page Drivetrain>TX6A (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM>DTC CHECK / CLEAR).


CHECK THE SHIFT POSITION


a.

Drive the vehicle with shift lever in the M.


b.

Check the shift position.

HINT:
·

The shift solenoid valve S1 is turned on/off normally when the shift lever is in the D position:

TCM command gearshift 1st 2nd 3rd 4th 5th 6th
Shift solenoid valve S1 OFF ON ON ON ON ON





PROCEDURE

1.CHECK OTHER DTCS OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch ON and push the GTS main switch ON.


c.

Read the DTCs using the GTS (See page Drivetrain>TX6A (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM>DTC CHECK / CLEAR).

Result:
Display (DTC output) Proceed to
"P0751 and P2714" or "P0752 and P0767" are output A
"P0751 and P2714" or "P0752 and P0767" and other DTCs B




A

2.HYDRAULIC TEST

B

2.HYDRAULIC TEST
C261940E03
2.354,0.844 1.604,0.271 1.604,0.271 1.406,0.271 false 4.646,1.427 5.271,2.229 5.271,2.229 5.5,2.229 true 3.083,3.771 3.26,4.323 3.26,4.323 3.333,4.323 true 1.208,0.208 1.427,0.396 0.219,0.188 10 false *1 5.552,2.156 5.833,2.375 0.281,0.219 10 false *1 3.396,4.24 3.563,4.417 0.167,0.177 10 false *2

Text in Illustration
*1 SST *2 Test Plug

NOTICE:
·

Perform the test at the normal operating ATF (Automatic Transmission Fluid) temperature: 60 to 90°C (140 to 194°F)

·

The line pressure test should always be carried out in pairs. One technician should observe the conditions of wheels or wheel stoppers outside the vehicle while the other is performing the test.

·

Be careful to prevent SST hose from interfering with the exhaust pipe.

·

This Check must be conducted after checking and adjusting engine.

·

Perform under condition that A/C is OFF.

·

When conducting stall test, do not continue more than 5 seconds.



a.

Warm up the ATF (Automatic Transmission Fluid).


b.

Lift the vehicle up.


c.

Remove the test plug on the transmission case center right side and connect SST.


SST
09992-00095  (09992-00231, 09992-00271)

d.

Lower the vehicle.


e.

Fully apply the parking brake and check the 4 wheels.


f.

Start the engine and check idling speed.


g.

Keep your left foot pressing firmly on the brake pedal and shift into D position.


h.

Measure the line pressure when the engine is idling.


i.

Depress the accelerator pedal all the way down. Quickly read the highest line pressure when engine speed reaches stall speed.


j.

In the same manner, do the test in R position.

Specified line pressure:
Condition D position kPa (kgf / cm2, psi) R position kPa (kgf / cm2, psi)
Idling 350 to 430 kPa
(3.6 to 4.4 kgf/cm2, 51 to 62 psi)
760 to 950 kPa
(7.7 to 9.7 kgf/cm2, 110 to 138 psi)
Stall test 1200 to 1380 kPa
(12.5 to 14.0 kgf/cm2, 174 to 200 psi)
1410 to 1630 kPa
(14.4 to 16.6 kgf/cm2, 204 to 236 psi)



OK

3.INSPECT SHIFT SOLENOID VALVE S1

NG

3.INSPECT SHIFT SOLENOID VALVE S1

b.

Perform inspection of the shift solenoid valve S1 (See page Drivetrain>TX6A (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>INSPECTION).



OK

4.INSPECT TRANSMISSION VALVE BODY ASSEMBLY

NG

4.INSPECT TRANSMISSION VALVE BODY ASSEMBLY
a.

Perform inspection of the transmission valve body assembly (See page Drivetrain>TX6A (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>INSPECTION).


OK:

There are no foreign objects on each valve.



OK

NG