Based upon a signal from the TCM, the combination of shift solenoid valve (S1, S2, S3, S4, SR, SL1, SL2) changes the gear position from 1st to 6th. As a fail-safe function if the solenoid valve system is open or shorted, the TCM cuts power to all solenoids, leaving just the mechanical hydraulic circuit, requiring manual shifting.
| DTC No. | DTC Detection Condition
1.
Diagnosis Condition 2.
Malfunction Status 3.
Malfunction Time 4.
Other |
Trouble Area |
|---|---|---|
| P0961 | 1.
Not learning control prohibited status Not open or short in the shift solenoid valve SL1 circuit 2.
The difference between the shift solenoid valve SL1 operational feedback current is 12 A or more in total. 3.
Detects "2.Malfunction Status" 2 times consecutively. 4.
1-trip detection logic |
·
Shift solenoid valve SL1 ·
Transmission wire ·
Harness and connector ·
TCM |
| P0962 | 1.
Not learning control prohibited status 1 second or more has elapsed after turning shift solenoid valve SL1 off. 2.
The shift solenoid valve SL1 operational feedback voltage is 0.018 V or less. 3.
Detects malfunction that continues for 100 ms or more 5 times consecutively. 4.
1-trip detection logic |
·
Shift solenoid valve SL1 ·
Transmission wire ·
Harness and connector ·
TCM |
| P0963 | 1.
Not learning control prohibited status 1 second or more has elapsed after turning shift solenoid valve SL1 on. 2.
The shift solenoid valve SL1 operational feedback voltage is 0.257 V or more. 3.
Detects malfunction that continues for 100 ms or more 5 times consecutively. 4.
1-trip detection logic |
·
Shift solenoid valve SL1 ·
Transmission wire ·
Harness and connector ·
TCM |
Reference (Using an oscilloscope):
Check the waveform between the terminals SL1+ and SL1- of the TCM connector
Refer to the illustration.
| Terminal | SL1+ - SL1- |
| Tool setting | 5 V/DIV., 1 ms./DIV. |
| Vehicle condition | 5th or 6th gear |
This DTC indicates an open, short, or feedback stuck in the shift solenoid valve SL1 circuit. The TCM commands gearshift by turning the shift solenoid valves "ON/OFF". When there is an open or short circuit in any shift solenoid valve circuit, the TCM detects the problem and illuminates the MIL and stores the DTC.
Perform the universal trip to clear permanent DTCs (See page Drivetrain>TX6A (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM>DTC CHECK / CLEAR).
The shift solenoid valve SL1 is turned on/off normally when the shift lever is in the D position:
| TCM command gearshift | 1st | 2nd | 3rd | 4th | 5th | 6th |
| Shift solenoid valve SL1 | OFF | OFF | OFF | OFF | ON | ON |
Disconnect the L4 transmission wire connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L4-11(SL1+) - L4-3(SL1-) | 20°C(68°F) | 5.0 to 5.6 Ω |
| L4-11(SL1+) - Body ground | Always | 10 kΩ or higher |
| L4-3(SL1-) - Body ground | Always | 10 kΩ or higher |
Connect the L4 transmission wire connector.
OK
NG
Disconnect the A18 TCM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A18-16(SL1+) - A18-12(SL1-) | 20°C(68°F) | 5.0 to 5.6 Ω |
| A18-16(SL1+) - Body ground | Always | 10 kΩ or higher |
| A18-12(SL1-) - Body ground | Always | 10 kΩ or higher |
Connect the A18 TCM connector.
OK
NG
Replace the TCM (See page Drivetrain>TX6A (AUTOMATIC TRANSMISSION / TRANSAXLE)>TCM>REMOVAL).
NEXT
(See pageDrivetrain>TX6A (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM>INITIALIZATION)
Remove the shift solenoid valve SL1 (See page Drivetrain>TX6A (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>REMOVAL).
Perform inspection of the shift solenoid valve SL1 (See page Drivetrain>TX6A (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>INSPECTION).
OK
NG