Home › Drivetrain › TX6A (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM
RM2090E _52 Drivetrain _060674 TX6A AUTOMATIC TRANSMISSION / TRANSAXLE _0297556 AUTOMATIC TRANSMISSION SYSTEM C

TX6A AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  P0965  Pressure Control Solenoid "B" Performance (SL2 Solenoid)  P0966  Pressure Control Solenoid "B" Control Circuit Low (Shift Solenoid Valve DS2)  P0967  Pressure Control Solenoid "B" Control Circuit High (Shift Solenoid Valve DS2)  


DESCRIPTION

Based upon a signal from the TCM, the combination of shift solenoid valves (S1, S2, S3, S4, SR, SL1, SL2) changes the gear position from 1st to 6th. As a fail-safe function, if the solenoid valve system is open or shorted, the TCM cuts power to all solenoids, leaving just the mechanical hydraulic circuit, requiring manual shifting.

DTC No. DTC Detection Condition
1.

Diagnosis Condition

2.

Malfunction Status

3.

Malfunction Time

4.

Other


Trouble Area
P0965
1.

Not learning control prohibited status

2.

The difference between the shift solenoid valve SL2 operational specified current and operational feedback current is 12 A or more in total.

3.

Detects "2.Malfunction Status" 2 times consecutively.

4.

1-trip detection logic


·

Shift solenoid valve SL2

·

Transmission wire

·

Harness and connector

·

TCM


P0966
1.

Not learning control prohibited status

1 second or more has elapsed after turning shift solenoid valve SL2 off

2.

The shift solenoid valve SL1 operational feedback voltage is 0.018 V or less.

3.

Detects malfunction that continues for 100 ms or more 5 times consecutively.

4.

1-trip detection logic


·

Shift solenoid valve SL2

·

Transmission wire

·

Harness and connector

·

TCM


P0967
1.

Not learning control prohibited status

1 second or more has elapsed after turning shift solenoid valve SL2 on

2.

The shift solenoid valve SL1 operational feedback voltage is 0.257 V or more.

3.

Detects malfunction that continues for 100 ms or more 5 times consecutively.

4.

1-trip detection logic


·

Shift solenoid valve SL2

·

Transmission wire

·

Harness and connector

·

TCM



Reference (Using an oscilloscope):

Check the waveform between the terminals SL2+ and SL2- of the TCM connector

G023426E24
2.719,0.208 3.26,0.406 0.542,0.198 10 false 5 V/DIV. 3,1.25 3.385,1.448 0.385,0.198 10 false GND 1.906,1.76 2.604,1.958 0.698,0.198 10 false 1 ms./DIV.

Standard:

Refer to the illustration.


Terminal SL2+ - SL2-
Tool setting 5 V/DIV., 1 ms./DIV.
Vehicle condition Engine idle speed

MONITOR DESCRIPTION

This DTC indicates an open, short or feedback stuck in the shift solenoid valve SL2 circuit. The TCM commands gear shifts by turning the shift solenoid valves "ON/OFF". When there is an open or short circuit in any shift solenoid valve circuit, the TCM detects the problem and illuminates the MIL and stores the DTC.

WIRING DIAGRAM

C250701E24
1.021,1.458 2.573,1.646 1.552,0.188 10 false Shift Solenoid Valve SL2 5.333,3.073 5.646,3.302 0.313,0.229 10 false TCM 4.823,2.01 5.292,2.177 0.469,0.167 10 false 11 5.354,2.917 5.625,3.083 0.271,0.167 10 false A18 5.177,2.104 5.646,2.271 0.469,0.167 10 false SL2- 4.875,0.802 5.344,0.969 0.469,0.167 10 false 5 5.167,1 6.052,1.188 0.885,0.188 10 false SL2+ 2.781,0.802 3.25,0.969 0.469,0.167 10 false 10 2.813,2.01 3.281,2.177 0.469,0.167 10 false 2 0.854,2.792 2.125,2.979 1.271,0.188 10 false Transmission Wire 0.875,2.635 1.083,2.833 0.208,0.198 10 false L4 2.313,0.802 2.781,0.969 0.469,0.167 10 false SL2+ 2.323,2.01 2.792,2.177 0.469,0.167 10 false SL2-

CAUTION / NOTICE / HINT

NOTICE:

Perform the universal trip to clear permanent DTCs (See page Drivetrain>TX6A (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM>DTC CHECK / CLEAR).


HINT:
·

The shift solenoid valve SL2 is turned on/off normally when the shift lever is in the D position:

TCM command gearshift 1st 2nd 3rd 4th 5th 6th
Shift solenoid valve SL2 ON OFF OFF ON OFF OFF



PROCEDURE

1.INSPECT TRANSMISSION WIRE (SL2)
a.

Disconnect the L4 transmission wire connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
L4-10(SL2+) - L4-2(SL2-) 20°C(68°F) 5.0 to 5.6 Ω
L4-10(SL2+) - Body ground Always 10 kΩ or higher
L4-2(SL2-) - Body ground Always 10 kΩ or higher



c.

Connect the L4 transmission wire connector.



OK

2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM)

NG

4.INSPECT SHIFT SOLENOID SL2
2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM)
a.

Disconnect the TCM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
A18-5(SL2+) - A18-11(SL2-) 20°C(68°F) 5.0 to 5.6 Ω
A18-5(SL2+) - Body ground Always 10 kΩ or higher
A18-11(SL2-) - Body ground Always 10 kΩ or higher



c.

Connect the TCM connector.



OK

3.REPLACE TCM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT SHIFT SOLENOID SL2

b.

Perform inspection of the shift solenoid valve SL2 (See page Drivetrain>TX6A (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>INSPECTION).



OK

NG