Home › Drivetrain › TX6A (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM
RM2090E _52 Drivetrain _060674 TX6A AUTOMATIC TRANSMISSION / TRANSAXLE _0297556 AUTOMATIC TRANSMISSION SYSTEM C

TX6A AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  P2762  Torque Converter Pressure Control Solenoid Circuit Performance (SLU / DSU Solenoid)  P2763  Torque Converter Clutch Pressure Control Solenoid Control Circuit High (Shift Solenoid Valve DSU)  P2764  Torque Converter Clutch Pressure Control Solenoid Control Circuit Low (Shift Solenoid Valve DSU)  


DESCRIPTION

The shift solenoid valve SLU is controlled by the duty ratio as determined in advance by the TCM. In this way, it carries out lock-up and flex lock-up control.

DTC No. DTC Detection Condition
1.

Diagnosis Condition

2.

Malfunction Status

3.

Malfunction Time

4.

Other


Trouble Area
P2762
1.

Not learning control prohibited status.

Not open or short in the shift solenoid valve SLU/DSU circuit.

2.

The difference between the shift solenoid valve SLU operational specified current and operational feedback current is 12 A or more in total.

3.

Detects "2.Malfunction Status" 5 times consecutively.

4.

1-trip detection logic


·

Shift solenoid valve SLU

·

Transmission wire

·

Harness and connector

·

TCM


P2763
1.

Not learning control prohibited status

Not malfunction with the shift solenoid valve SLU/DSU circuit performance.

2.

1 second or more has elapsed after turning shift solenoid valve SLU off.

The shift solenoid valve SLU operational feedback voltage is 0.018 V or less.

3.

Detects malfunction that continues for 100 ms or more 5 times consecutively.

4.

1-trip detection logic


·

Shift solenoid valve SLU

·

Transmission wire

·

Harness and connector

·

TCM


P2764
1.

Not learning control prohibited status

Not malfunction with the shift solenoid valve SLU/DSU circuit performance.

2.

1 second or more has elapsed after turning shift solenoid valve SLU on.

The shift solenoid valve SLU operational feedback voltage is 0.257 V or more.

3.

Detects malfunction that continues for 100 ms or more 5 times consecutively.

4.

1-trip detection logic


·

Shift solenoid valve SLU

·

Transmission wire

·

Harness and connector

·

TCM



MONITOR DESCRIPTION

When an open or short in a shift solenoid valve SLU circuit or feedback Stuck is detected, the TCM determines there is a malfunction. The TCM will turn on the MIL and store this DTC.

WIRING DIAGRAM

C250701E27
1.021,1.479 2.573,1.646 1.552,0.167 10 false Shift Solenoid Valve SLU 5.375,3.073 5.698,3.292 0.323,0.219 10 false TCM 4.927,2.01 5.115,2.198 0.188,0.188 10 false 1 5.396,2.927 5.688,3.135 0.292,0.208 10 false A18 5.135,2.104 5.5,2.271 0.365,0.167 10 false SLU- 4.844,0.802 5.125,0.99 0.281,0.188 10 false 13 5.135,1 5.583,1.198 0.448,0.198 10 false SLU+ 2.771,0.792 3.24,0.958 0.469,0.167 10 false 12 2.802,2.01 3.271,2.177 0.469,0.167 10 false 4 0.802,2.75 1.99,3 1.188,0.25 10 false Transmission Wire 0.823,2.615 1.094,2.771 0.271,0.156 10 false L4 2.313,0.802 2.938,0.979 0.625,0.177 10 false SLU+ 2.323,2.01 3.031,2.167 0.708,0.156 10 false SLU-

CAUTION / NOTICE / HINT

NOTICE:

Perform the universal trip to clear permanent DTCs (See page Drivetrain>TX6A (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM>DTC CHECK / CLEAR).


PROCEDURE

1.INSPECT TRANSMISSION WIRE (SLU)
a.

Disconnect the L4 transmission wire connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
L4-12(SLU+) - L4-4(SLU-) 20°C(68°F) 5.0 to 5.6 Ω
L4-12(SLU+) - Body ground Always 10 kΩ or higher
L4-4(SLU-) - Body ground Always 10 kΩ or higher



c.

Connect the L4 transmission wire connector.



OK

2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM)

NG

4.INSPECT SHIFT SOLENOID VALVE SLU
2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM)
a.

Disconnect the A18 TCM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
A18-13(SLU+) - A18-1(SLU-) 20°C(68°F) 5.0 to 5.6 Ω
A18-13(SLU+) - Body ground Always 10 kΩ or higher
A18-1(SLU-) - Body ground Always 10 kΩ or higher



c.

Connect the A18 TCM connector.



OK

3.REPLACE TCM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT SHIFT SOLENOID VALVE SLU

b.

Perform inspection of the shift solenoid valve SLU (See page Drivetrain>TX6A (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>INSPECTION).



OK

NG