Home › Drivetrain › TL70 (MANUAL TRANSMISSION / TRANSAXLE) › SHIFT LEVER ASSEMBLY
RM2090E _52 Drivetrain _060676 TL70 MANUAL TRANSMISSION / TRANSAXLE _0297578 SHIFT LEVER ASSEMBLY A

TL70 MANUAL TRANSMISSION / TRANSAXLE  SHIFT LEVER ASSEMBLY  REMOVAL  


PROCEDURE

Hide 1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 58810J 2.REMOVE CONSOLE BOX ASSEMBLY

Hide 33555 3.REMOVE SHIFT LEVER BOOT

a.
C260582

Remove the 2 clips and the shift and select lever cover.


b.
C260583

Disconnect the wire harness clamp.


c.

Remove the 4 bolts, the shift and select lever retainer and the shift lever boot.


Hide 33554 4.REMOVE SHIFT LEVER CAP

a.
C260584

Remove the 4 bolts and the shift lever cap.


Hide 37100 5.REMOVE PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY

Hide 33530F 6.REMOVE FLOOR SHIFT LEVER ASSEMBLY

a.
C260585

Turn over the shift and select lever boot.


b.

Using a screwdriver, remove the clip and the floor shift lever assembly.


c.

Remove the plate washer from the floor shift lever assembly.


d.

Remove the 2 collars and O-ring from the floor shift lever assembly.


Hide 33555B 7.REMOVE SHIFT AND SELECT LEVER BOOT

a.

Remove the shift and select lever boot from the floor shift lever assembly.


Hide 33506F 8.REMOVE FLOOR SHIFT CONTROL SHIFT LEVER RETAINER SUB-ASSEMBLY

a.
C260586

Remove the 2 bolts and separate the floor shift control shift lever retainer sub-assembly.


b.
C261652

Remove the floor shift control shift lever retainer sub-assembly.


Hide 33575 10.REMOVE FLOOR SHIFT CONTROL SHIFT LEVER RETAINER

a.
C262640

Pull up the locks of the shift lever pins, and remove the 2 shift lever pins.


b.

Remove the floor shift control shift lever retainer.


Hide 11.REMOVE SHIFT LEVER RETAINER BUSHING

a.
C261651

Remove the 4 shift lever retainer bushings.


Hide 33511 12.REMOVE FLOOR SHIFT CONTROL SHAFT

C262641

a.

Using a screwdriver, remove the clip, plate washer and floor shift control shaft.


b.

Remove the 2 collars from the control shaft.


Hide 33511G 13.REMOVE CONTROL SHAFT

C262642E03
1.479,3.031 1.365,2.792 true 1.698,3.177 2,2.823 true 2.74,3.625 2.979,3.833 true 1.927,3.552 2.26,4.01 true 0.698,3.865 0.927,4.135 true 2.021,2.656 2.188,2.833 0.167,0.177 10 false *2 3.021,3.74 3.188,3.917 0.167,0.177 10 false *3 1.198,2.667 1.365,2.844 0.167,0.177 10 false *1 2.26,4.042 2.427,4.219 0.167,0.177 10 false *4 0.896,4.156 1.063,4.333 0.167,0.177 10 false *5

a.

Using a hammer and a screwdriver, cut off the control shaft collar and remove it from the shift shaft.


b.

Using a hexagon bar wrench, push the shaft pin up from the bottom. Attach a piece of cloth to protect the shaft pin from damage, and then remove the shaft pin using a pair of pliers.


c.

Remove the shift lever damper from the control shaft.

Text in Illustration
*1 Control Shaft Collar
*2 Shaft Pin
*3 Control Shaft
*4 Shift Lever Damper
*5 Shift Shaft