Each speed sensor detects wheel speed and sends the appropriate signals to the skid control ECU (brake actuator assembly). These signals are used by the brake control system.
Speed sensor rotors have row of alternating N and S magnetic poles, and their magnetic fields change when the rotors turn.
Each speed sensor detects that magnetic field change and sends a pulse signal to the skid control ECU (brake actuator assembly).
DTCs C1271 and C1272 are cleared when the speed sensor sends a vehicle speed signal or when Test Mode ends. DTCs C1271 and C1272 are output only in Test Mode.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| C1330
C1331 |
An open or short in the speed sensor signal circuit. | ·
Front speed sensor RH/LH ·
Speed sensor circuit ·
Sensor installation ·
Skid control ECU |
| C1464
C1465 |
An abnormal signal is received from a wheel speed sensor. | ·
Front speed sensor RH/LH ·
Speed sensor circuit ·
Front speed sensor rotor RH/LH (Front axle hub sub-assembly RH/LH) ·
Sensor installation ·
Skid control ECU |
| C1271
C1272 |
Detected only during Test Mode. | ·
Front speed sensor RH/LH ·
Sensor installation ·
Front speed sensor rotor RH/LH (Front axle hub sub-assembly RH/LH) |
DTCs C1271, C1330 and C1464 are for the front speed sensor RH.
DTCs C1272, C1331 and C1465 are for the front speed sensor LH.
When replacing the skid control ECU (brake actuator assembly), perform VSC sensor neutral memorization (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).
Connect the GTS to the DLC3.
Start the engine.
Select the Data List using the GTS (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| FR Wheel Speed | Front wheel speed sensor RH reading / Min.: 0 km/h (0 mph), Max.: 326.4 km/h (202 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| FL Wheel Speed | Front wheel speed sensor LH reading / Min.: 0 km/h (0 mph), Max.: 326.4 km/h (202 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
Check the speed value output from the speed sensor displayed on the GTS.
Factors that affect the indicated vehicle speed include tire size, tire pressure, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>ON-VEHICLE INSPECTION).
The speed value output from the speed sensor displayed on the GTS is similar to the speed indicated on the speedometer.
OK
NG
Turn the ignition switch off.
Perform the sensor check using the Test Mode procedure (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE).
All Test Mode DTCs are not output.
OK
NG
Clear the DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off.
Start the engine.
Drive the vehicle at a speed of 45 km/h (28 mph) or more for at least 120 seconds.
Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTCs C1330, C1331, C1464 and C1465 are not output. | A |
| DTCs C1330, C1331, C1464 and/or C1465 are output. | B |
A
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
B
Turn the ignition switch off.
Check the speed sensor installation.
There is no clearance between the sensor and the steering knuckle.
The installation bolt is tightened properly.
7.5 N*m (76 kgf*cm, 66 in.*lbf)
OK
NG
Remove the front speed sensor (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SPEED SENSOR>REMOVAL).
Check the speed sensor tip.
No scratches or foreign matter on the sensor tip.
Check the speed sensor signal after cleaning or replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE).
OK
NG
Install the front speed sensor (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SPEED SENSOR>INSTALLATION).
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
Disconnect the skid control ECU (brake actuator assembly) connector and the front speed sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A5-16 (FR+) - A42-2 (FR+) | Always | Below 1 Ω |
| A5-16 (FR+) - Body ground | Always | 10 kΩ or higher |
| A5-4 (FR-) - A42-1 (FR-) | Always | Below 1 Ω |
| A5-4 (FR-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A5-19 (FL+) - A12-2 (FL+) | Always | Below 1 Ω |
| A5-19 (FL+) - Body ground | Always | 10 kΩ or higher |
| A5-32 (FL-) - A12-1 (FL-) | Always | Below 1 Ω |
| A5-32 (FL-) - Body ground | Always | 10 kΩ or higher |
OK
NG
Reconnect the skid control ECU (brake actuator assembly) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A42-2 (FR+) - Body ground | Ignition switch ON | 8 to 14 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A12-2 (FL+) - Body ground | Ignition switch ON | 8 to 14 V |
| *A | for RH |
| *B | for LH |
| *a | Front view of wire harness connector
(to Front Speed Sensor) |
OK
NG
Reconnect the front speed sensor connector.
Clear the DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off.
Start the engine.
Drive the vehicle at a speed of 45 km/h (28 mph) or more for at least 120 seconds.
Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTCs C1330, C1331, C1464 and/or C1465 are output. | A |
| DTCs C1330, C1331, C1464 and C1465 are not output. | B |
A
B
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
Turn the ignition switch off.
Replace the front speed sensor (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SPEED SENSOR>REMOVAL).
Check the speed sensor signal after replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE).
NEXT
Clear the DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off.
Start the engine.
Drive the vehicle at a speed of 45 km/h (28 mph) or more for at least 120 seconds.
Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTCs C1330, C1331, C1464 and/or C1465 are output. | A |
| DTCs C1330, C1331, C1464 and C1465 are not output. | B |
A
B
Turn the ignition switch off.
Replace the front speed sensor rotor (See page Drivetrain>AXLE AND DIFFERENTIAL>FRONT AXLE HUB>REMOVAL).
If the front speed sensor rotor needs to be replaced, replace the front axle hub sub-assembly.
Check the speed sensor signal after replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE).
NEXT
Clear the DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off.
Start the engine.
Drive the vehicle at a speed of 45 km/h (28 mph) or more for at least 120 seconds.
Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTCs C1330, C1331, C1464 and/or C1465 are output. | A |
| DTCs C1330, C1331, C1464 and C1465 are not output. | B |
If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE).
A
B