Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2014.05
RM2090E _54 Brake _060684 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0297617 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1271  Low Output Signal of Front Speed Sensor RH (Test Mode DTC)  C1272  Low Output Signal of Front Speed Sensor LH (Test Mode DTC)  C1330  Open in Front Speed Sensor RH  C1331  Open in Front Speed Sensor LH  C1464  Front Speed Sensor RH  C1465  Front Speed Sensor LH  


DESCRIPTION

Each speed sensor detects wheel speed and sends the appropriate signals to the skid control ECU (brake actuator assembly). These signals are used by the brake control system.

Speed sensor rotors have row of alternating N and S magnetic poles, and their magnetic fields change when the rotors turn.

Each speed sensor detects that magnetic field change and sends a pulse signal to the skid control ECU (brake actuator assembly).

DTCs C1271 and C1272 are cleared when the speed sensor sends a vehicle speed signal or when Test Mode ends. DTCs C1271 and C1272 are output only in Test Mode.

F100269E26
1.552,1.073 1.552,0.542 1.552,0.542 1.406,0.542 false 1.229,1.323 1.417,1.625 true 1.094,1.385 1.385,1.635 true 1,1.521 1.365,1.667 true 0.99,1.698 1.333,1.698 true 0.479,0.469 1.406,0.667 0.927,0.198 10 false Speed Sensor 1.167,2.198 2.458,2.396 1.292,0.198 10 false Speed Sensor Rotor 6.323,1.313 6.885,1.563 0.563,0.25 10 false 14 mA 6.365,1.646 6.729,1.844 0.365,0.198 10 false 7 mA 4.292,2.115 5.021,2.313 0.729,0.198 10 false Low speed 5.26,2.167 6.021,2.396 0.76,0.229 10 false High speed 1.125,1.156 1.281,1.354 0.156,0.198 10 false N 0.948,1.229 1.104,1.427 0.156,0.198 10 false S 0.854,1.417 1.01,1.615 0.156,0.198 10 false N 0.823,1.625 0.979,1.823 0.156,0.198 10 false S

DTC No. DTC Detection Condition Trouble Area
C1330
C1331
An open or short in the speed sensor signal circuit.
·

Front speed sensor RH/LH

·

Speed sensor circuit

·

Sensor installation

·

Skid control ECU


C1464
C1465
An abnormal signal is received from a wheel speed sensor.
·

Front speed sensor RH/LH

·

Speed sensor circuit

·

Front speed sensor rotor RH/LH (Front axle hub sub-assembly RH/LH)

·

Sensor installation

·

Skid control ECU


C1271
C1272
Detected only during Test Mode.
·

Front speed sensor RH/LH

·

Sensor installation

·

Front speed sensor rotor RH/LH (Front axle hub sub-assembly RH/LH)



HINT:
·

DTCs C1271, C1330 and C1464 are for the front speed sensor RH.

·

DTCs C1272, C1331 and C1465 are for the front speed sensor LH.



WIRING DIAGRAM

C261863E04
5.052,2.823 5.677,2.99 0.625,0.167 10 false A5 5.052,2.979 6.604,3.427 1.552,0.448 10 false Skid Control ECU (Brake Actuator Assembly) 0.281,1.896 0.906,2.073 0.625,0.177 10 false A12 0.271,0.865 1.125,1.229 0.854,0.365 10 false Front Speed Sensor RH 2.177,0.615 2.313,0.771 0.135,0.156 10 false 2 2.188,1.073 2.313,1.25 0.125,0.177 10 false 1 0.281,2.073 1.094,2.438 0.813,0.365 10 false Front Speed Sensor LH 2.177,1.823 2.292,1.979 0.115,0.156 10 false 2 2.188,2.302 2.313,2.458 0.125,0.156 10 false 1 0.271,0.688 0.844,0.875 0.573,0.188 10 false A42 5.438,1.885 5.99,2.083 0.552,0.198 10 false FL+ 5.438,2.385 6.125,2.583 0.688,0.198 10 false FL- 5.438,0.688 6.302,0.917 0.865,0.229 10 false FR+ 5.438,1.177 6.156,1.375 0.719,0.198 10 false FR- 1.802,1.906 2.927,2.083 1.125,0.177 10 false FL+ 1.802,2.385 2.917,2.594 1.115,0.208 10 false FL- 1.802,0.688 2.802,0.938 1,0.25 10 false FR+ 1.802,1.177 2.823,1.365 1.021,0.188 10 false FR- 5.156,0.604 5.979,0.771 0.823,0.167 10 false 16 5.198,1.083 5.917,1.26 0.719,0.177 10 false 4 5.156,1.802 5.719,1.979 0.563,0.177 10 false 19 5.208,2.292 5.875,2.469 0.667,0.177 10 false 8

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform VSC sensor neutral memorization (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).


PROCEDURE

1.READ VALUE USING GTS (FRONT SPEED SENSOR)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Select the Data List using the GTS (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST).

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
FR Wheel Speed Front wheel speed sensor RH reading / Min.: 0 km/h (0 mph), Max.: 326.4 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
FL Wheel Speed Front wheel speed sensor LH reading / Min.: 0 km/h (0 mph), Max.: 326.4 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations


d.

Check the speed value output from the speed sensor displayed on the GTS.

HINT:

Factors that affect the indicated vehicle speed include tire size, tire pressure, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>ON-VEHICLE INSPECTION).


OK:

The speed value output from the speed sensor displayed on the GTS is similar to the speed indicated on the speedometer.




OK

2.PERFORM TEST MODE INSPECTION (SIGNAL CHECK)

NG

4.CHECK FRONT SPEED SENSOR INSTALLATION
2.PERFORM TEST MODE INSPECTION (SIGNAL CHECK)
a.

Turn the ignition switch off.


b.

Perform the sensor check using the Test Mode procedure (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE).

OK:

All Test Mode DTCs are not output.




OK

3.RECONFIRM DTC

NG

4.CHECK FRONT SPEED SENSOR INSTALLATION
3.RECONFIRM DTC

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 45 km/h (28 mph) or more for at least 120 seconds.


e.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTCs C1330, C1331, C1464 and C1465 are not output. A
DTCs C1330, C1331, C1464 and/or C1465 are output. B




A

B

9.REPLACE FRONT SPEED SENSOR
4.CHECK FRONT SPEED SENSOR INSTALLATION
a.
C168336E24
1.031,0.833 1.24,0.646 false 0.948,1.49 1.271,1.677 false 0.115,0.104 0.813,0.406 0.698,0.302 10 false *1 1.271,0.5 1.51,0.74 0.24,0.24 10 false *c 1.323,1.583 1.563,1.823 0.24,0.24 10 false *d 0.719,1.802 0.958,2.042 0.24,0.24 10 false *a 2.438,1.875 2.677,2.115 0.24,0.24 10 false *b

Turn the ignition switch off.


b.

Check the speed sensor installation.

OK:

There is no clearance between the sensor and the steering knuckle.

The installation bolt is tightened properly.

Torque:

7.5 N*m (76 kgf*cm, 66 in.*lbf)


Text in Illustration
*1 Front Speed Sensor
*a Correct
*b Incorrect
*c 7.5 N*m
*d No clearance



OK

5.CHECK FRONT SPEED SENSOR TIP

NG

5.CHECK FRONT SPEED SENSOR TIP

b.

Check the speed sensor tip.

OK:

No scratches or foreign matter on the sensor tip.


NOTICE:

Check the speed sensor signal after cleaning or replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE).




OK

6.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - FRONT SPEED SENSOR)

NG

CLEAN OR REPLACE FRONT SPEED SENSOR

6.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - FRONT SPEED SENSOR)

b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


c.

Disconnect the skid control ECU (brake actuator assembly) connector and the front speed sensor connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH:
Tester Connection Condition Specified Condition
A5-16 (FR+) - A42-2 (FR+) Always Below 1 Ω
A5-16 (FR+) - Body ground Always 10 kΩ or higher
A5-4 (FR-) - A42-1 (FR-) Always Below 1 Ω
A5-4 (FR-) - Body ground Always 10 kΩ or higher

for LH:
Tester Connection Condition Specified Condition
A5-19 (FL+) - A12-2 (FL+) Always Below 1 Ω
A5-19 (FL+) - Body ground Always 10 kΩ or higher
A5-8 (FL-) - A12-1 (FL-) Always Below 1 Ω
A5-8 (FL-) - Body ground Always 10 kΩ or higher




OK

7.INSPECT BRAKE ACTUATOR ASSEMBLY (FRONT SPEED SENSOR POWER SOURCE TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT BRAKE ACTUATOR ASSEMBLY (FRONT SPEED SENSOR POWER SOURCE TERMINAL)
a.

Reconnect the skid control ECU (brake actuator assembly) connector.


b.
U147146E02
1.656,1.156 1.656,1.552 true 0.104,0.042 0.313,0.219 0.208,0.177 10 false *a 0.542,0.865 0.854,1.042 0.313,0.177 10 false A42 0.938,0.865 1.125,1.042 0.188,0.177 10 false *A 0.542,1.177 0.844,1.354 0.302,0.177 10 false A12 0.948,1.177 1.125,1.354 0.177,0.177 10 false *B 1.438,1.573 1.927,2.021 0.49,0.448 10 false FR+*A, FL+*B

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for RH:
Tester Connection Condition Specified Condition
A42-2 (FR+) - Body ground Ignition switch ON 8 to 14 V

for LH:
Tester Connection Condition Specified Condition
A12-2 (FL+) - Body ground Ignition switch ON 8 to 14 V


Text in Illustration
*A for RH
*B for LH
*a Front view of wire harness connector
(to Front Speed Sensor)



OK

8.RECONFIRM DTC

NG

8.RECONFIRM DTC
a.

Reconnect the front speed sensor connector.



c.

Turn the ignition switch off.


d.

Start the engine.


e.

Drive the vehicle at a speed of 45 km/h (28 mph) or more for at least 120 seconds.


f.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTCs C1330, C1331, C1464 and/or C1465 are output. A
DTCs C1330, C1331, C1464 and C1465 are not output. B




A

9.REPLACE FRONT SPEED SENSOR

B

9.REPLACE FRONT SPEED SENSOR
a.

Turn the ignition switch off.


b.

Replace the front speed sensor (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SPEED SENSOR>REMOVAL).

NOTICE:

Check the speed sensor signal after replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE).




NEXT

10.RECONFIRM DTC
10.RECONFIRM DTC

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 45 km/h (28 mph) or more for at least 120 seconds.


e.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTCs C1330, C1331, C1464 and/or C1465 are output. A
DTCs C1330, C1331, C1464 and C1465 are not output. B




A

11.REPLACE FRONT SPEED SENSOR ROTOR

B

END

11.REPLACE FRONT SPEED SENSOR ROTOR
a.

Turn the ignition switch off.


b.

Replace the front speed sensor rotor (See page Drivetrain>AXLE AND DIFFERENTIAL>FRONT AXLE HUB>REMOVAL).

HINT:

If the front speed sensor rotor needs to be replaced, replace the front axle hub sub-assembly.


NOTICE:

Check the speed sensor signal after replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE).




NEXT

12.RECONFIRM DTC
12.RECONFIRM DTC

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 45 km/h (28 mph) or more for at least 120 seconds.


e.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTCs C1330, C1331, C1464 and/or C1465 are output. A
DTCs C1330, C1331, C1464 and C1465 are not output. B


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE).




A

B

END