Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM
RM2090E _54 Brake _060684 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0297617 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1273  Low Output Signal of Rear Speed Sensor RH (Test Mode DTC)  C1274  Low Output Signal of Rear Speed Sensor LH (Test Mode DTC)  C1332  Open in Rear Speed Sensor RH  C1333  Open in Rear Speed Sensor LH  C1466  Rear Speed Sensor RH  C1467  Rear Speed Sensor LH  


DESCRIPTION

Each speed sensor detects the wheel speed and sends the appropriate signals to the skid control ECU (brake actuator assembly). These signals are used by the brake control system.

Speed sensor rotors have row of alternating N and S magnetic poles, and their magnetic fields change when the rotors turn.

Each speed sensor detects that magnetic field change and sends a pulse signal to the skid control ECU (brake actuator assembly).

DTCs C1273 and C1274 are cleared when the speed sensor sends a vehicle speed signal or when Test Mode ends. DTCs C1273 and C1274 are output only in Test Mode.

F100269E26
1.552,1.073 1.552,0.542 1.552,0.542 1.406,0.542 false 1.229,1.323 1.417,1.625 true 1.094,1.385 1.385,1.635 true 1,1.521 1.365,1.667 true 0.99,1.698 1.333,1.698 true 0.479,0.469 1.406,0.667 0.927,0.198 10 false Speed Sensor 1.167,2.198 2.458,2.396 1.292,0.198 10 false Speed Sensor Rotor 6.323,1.313 6.885,1.563 0.563,0.25 10 false 14 mA 6.365,1.646 6.729,1.844 0.365,0.198 10 false 7 mA 4.292,2.115 5.021,2.313 0.729,0.198 10 false Low speed 5.26,2.167 6.021,2.396 0.76,0.229 10 false High speed 1.125,1.156 1.281,1.354 0.156,0.198 10 false N 0.948,1.229 1.104,1.427 0.156,0.198 10 false S 0.854,1.417 1.01,1.615 0.156,0.198 10 false N 0.823,1.625 0.979,1.823 0.156,0.198 10 false S

DTC No. DTC Detection Condition Trouble Area
C1332
C1333
An open or short in the speed sensor signal circuit.
·

Rear speed sensor RH/LH

·

Speed sensor circuit

·

Sensor installation

·

Skid control ECU


C1466
C1467
An abnormal signal is received from a wheel speed sensor.
·

Rear speed sensor RH/LH

·

Speed sensor circuit

·

Rear speed sensor rotor RH/LH (Rear axle hub and bearing assembly RH/LH)

·

Sensor installation

·

Skid control ECU


C1273
C1274
Detected only during Test Mode.
·

Rear speed sensor RH/LH

·

Sensor installation

·

Rear speed sensor rotor RH/LH (Rear axle hub and bearing assembly RH/LH)



HINT:
·

DTCs C1273, C1332 and C1466 are for the rear speed sensor RH.

·

DTCs C1274, C1333 and C1467 are for the rear speed sensor LH.



WIRING DIAGRAM

C261863E07
4.969,2.802 5.594,2.969 0.625,0.167 10 false A5 4.948,2.979 6.896,3.521 1.948,0.542 10 false Skid Control ECU (Brake Actuator Assembly) 0.281,1.896 0.906,2.073 0.625,0.177 10 false H12 0.25,0.865 1.198,1.26 0.948,0.396 10 false Rear Speed Sensor RH 2.177,0.615 2.313,0.771 0.135,0.156 10 false 2 2.188,1.073 2.313,1.25 0.125,0.177 10 false 1 0.25,2.073 1.208,2.427 0.958,0.354 10 false Rear Speed Sensor LH 2.177,1.823 2.292,1.979 0.115,0.156 10 false 2 2.188,2.302 2.313,2.458 0.125,0.156 10 false 1 0.271,0.688 0.844,0.875 0.573,0.188 10 false G9 5.438,1.885 5.99,2.083 0.552,0.198 10 false RL+ 5.438,2.385 6.125,2.583 0.688,0.198 10 false RL- 5.438,0.688 6.302,0.917 0.865,0.229 10 false RR+ 5.438,1.177 6.156,1.375 0.719,0.198 10 false RR- 1.802,1.906 2.927,2.083 1.125,0.177 10 false RL+ 1.802,2.385 2.917,2.594 1.115,0.208 10 false RL- 1.802,0.688 2.802,0.938 1,0.25 10 false RR+ 1.802,1.177 2.823,1.365 1.021,0.188 10 false RR- 5.156,0.604 5.979,0.771 0.823,0.167 10 false 17 5.146,1.083 5.865,1.26 0.719,0.177 10 false 29 5.156,1.802 5.719,1.979 0.563,0.177 10 false 31 5.156,2.292 5.823,2.469 0.667,0.177 10 false 18

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform VSC sensor neutral memorization (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).


PROCEDURE

1.READ VALUE USING GTS (REAR SPEED SENSOR)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Select the Data List using the GTS (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST).

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
RR Wheel Speed Rear wheel speed sensor RH reading / Min.: 0 km/h (0 mph), Max.: 326.4 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
RL Wheel Speed Rear wheel speed sensor LH reading / Min.: 0 km/h (0 mph), Max.: 326.4 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations


d.

Check the speed value output from the speed sensor displayed on the GTS.

HINT:

Factors that affect the indicated vehicle speed include tire size, tire pressure, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>ON-VEHICLE INSPECTION).


OK:

The speed value output from the speed sensor displayed on the GTS is similar to the speed indicated on the speedometer.




OK

2.PERFORM TEST MODE INSPECTION (SIGNAL CHECK)

NG

4.CHECK REAR SPEED SENSOR INSTALLATION
2.PERFORM TEST MODE INSPECTION (SIGNAL CHECK)
a.

Turn the ignition switch off.


b.

Perform the sensor check using the Test Mode procedure (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE).

OK:

All Test Mode DTCs are not output.




OK

3.RECONFIRM DTC

NG

4.CHECK REAR SPEED SENSOR INSTALLATION
3.RECONFIRM DTC

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 45 km/h (28 mph) or more for at least 120 seconds.


e.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTCs C1332, C1333, C1466 and C1467 are not output. A
DTCs C1332, C1333, C1466 and/or C1467 are output. B




A

B

9.REPLACE REAR SPEED SENSOR
4.CHECK REAR SPEED SENSOR INSTALLATION
a.
C144929E90
0.833,1.625 0.833,0.76 false 0.833,0.76 0.979,0.76 false 0.698,2.479 0.958,2.792 false 0.958,2.792 1.073,2.792 false 0.625,2.885 0.906,3.083 0.281,0.198 10 false OK 2.667,2.938 2.99,3.135 0.323,0.198 10 false NG 1.115,2.708 2.031,2.906 0.917,0.198 10 false No clearance 1.031,0.667 1.573,0.865 0.542,0.198 10 false 7.5 N*m 0.094,0.073 1.542,0.271 1.448,0.198 10 false Rear Speed Sensor:

Turn the ignition switch off.


b.

Check the speed sensor installation.

OK:

There is no clearance between the sensor and the rear axle carrier sub-assembly.

The installation bolt is tightened properly.

Torque:

7.5 N*m (76 kgf*cm, 66 in.*lbf)




OK

5.CHECK REAR SPEED SENSOR TIP

NG

5.CHECK REAR SPEED SENSOR TIP

b.

Check the speed sensor tip.

OK:

No scratches or foreign matter on the sensor tip.


NOTICE:

Check the speed sensor signal after cleaning or replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE).




OK

6.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - REAR SPEED SENSOR)

NG

CLEAN OR REPLACE REAR SPEED SENSOR

6.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - REAR SPEED SENSOR)

b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


c.

Disconnect the skid control ECU (brake actuator assembly) connector and the rear speed sensor connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH:
Tester Connection Condition Specified Condition
A5-17 (RR+) - G9-2 (RR+) Always Below 1 Ω
A5-17 (RR+) - Body ground Always 10 kΩ or higher
A5-29 (RR-) - G9-1 (RR-) Always Below 1 Ω
A5-29 (RR-) - Body ground Always 10 kΩ or higher

for LH:
Tester Connection Condition Specified Condition
A5-31 (RL+) - H12-2 (RL+) Always Below 1 Ω
A5-31 (RL+) - Body ground Always 10 kΩ or higher
A5-18 (RL-) - H12-1 (RL-) Always Below 1 Ω
A5-18 (RL-) - Body ground Always 10 kΩ or higher




OK

7.INSPECT BRAKE ACTUATOR ASSEMBLY (REAR SPEED SENSOR POWER SOURCE TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT BRAKE ACTUATOR ASSEMBLY (REAR SPEED SENSOR POWER SOURCE TERMINAL)
a.

Reconnect the skid control ECU (brake actuator assembly) connector.


b.
U147147E03
1.646,1.188 1.646,1.646 true 0.104,0.01 0.313,0.188 0.208,0.177 10 false *a 0.563,0.865 0.875,1.042 0.313,0.177 10 false G9 0.948,0.875 1.135,1.052 0.188,0.177 10 false *A 0.542,1.177 0.844,1.354 0.302,0.177 10 false H12 0.948,1.177 1.125,1.354 0.177,0.177 10 false *B 1.438,1.646 1.927,2.01 0.49,0.365 10 false RR+*A, RL+*B

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for RH:
Tester Connection Condition Specified Condition
G9-2 (RR+) - Body ground Ignition switch ON 8 to 14 V

for LH:
Tester Connection Condition Specified Condition
H12-2 (RL+) - Body ground Ignition switch ON 8 to 14 V


Text in Illustration
*A for RH
*B for LH
*a Front view of wire harness connector
(to Rear Speed Sensor)



OK

8.RECONFIRM DTC

NG

8.RECONFIRM DTC
a.

Reconnect the rear speed sensor connector.



c.

Turn the ignition switch off.


d.

Start the engine.


e.

Drive the vehicle at a speed of 45 km/h (28 mph) or more for at least 120 seconds.


f.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTCs C1332, C1333, C1466 and/or C1467 are output. A
DTCs C1332, C1333, C1466 and C1467 are not output. B




A

9.REPLACE REAR SPEED SENSOR

B

9.REPLACE REAR SPEED SENSOR
a.

Turn the ignition switch off.


b.

Replace the rear speed sensor (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>REAR SPEED SENSOR>REMOVAL).

NOTICE:

Check the speed sensor signal after replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE).




NEXT

10.RECONFIRM DTC
10.RECONFIRM DTC

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 45 km/h (28 mph) or more for at least 120 seconds.


e.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTCs C1332, C1333, C1466 and/or C1467 are output. A
DTCs C1332, C1333, C1466 and C1467 are not output. B




A

11.REPLACE REAR SPEED SENSOR ROTOR

B

END

11.REPLACE REAR SPEED SENSOR ROTOR
a.

Turn the ignition switch off.


b.

Replace the rear speed sensor rotor (See page Drivetrain>AXLE AND DIFFERENTIAL>REAR AXLE HUB>REMOVAL).

HINT:

If the rear speed sensor rotor needs to be replaced, replace the rear axle hub and bearing assembly.


NOTICE:

Check the speed sensor signal after replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE).




NEXT

12.RECONFIRM DTC
12.RECONFIRM DTC

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 45 km/h (28 mph) or more for at least 120 seconds.


e.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTCs C1332, C1333, C1466 and/or C1467 are output. A
DTCs C1332, C1333, C1466 and C1467 are not output. B


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE).




A

B

END