Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2012.03–2019.03
RM2090E _54 Brake _060684 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0297617 VEHICLE STABILITY CONTROL SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  TRC OFF Indicator Light Remains ON  


DESCRIPTION

The skid control ECU (brake actuator assembly) is connected to the combination meter assembly via CAN communication.

Pressing the VSC OFF switch turns off TRC, and pressing and holding this switch turns off TRC and VSC. If TRC is turned off, the TRC OFF indicator light will come on.

WIRING DIAGRAM

C264064E07
5.49,4.01 7.146,4.531 1.656,0.521 10 false Skid Control ECU (Brake Actuator Assembly) 5.49,3.833 5.76,4.042 0.271,0.208 10 false A5 0.167,4 1.438,4.344 1.271,0.344 10 false Combination Meter Assembly 0.177,3.833 0.479,4.073 0.302,0.24 10 false D7 5.917,0.813 6.51,1.073 0.594,0.26 10 false CANL 5.917,1.448 6.51,1.781 0.594,0.333 10 false CANH 5.646,0.667 5.927,0.885 0.281,0.219 10 false 14 5.646,1.281 5.969,1.542 0.323,0.26 10 false 26 0.833,0.802 1.542,1.094 0.708,0.292 10 false CANL 0.833,1.438 1.438,1.698 0.604,0.26 10 false CANH 1.323,0.656 1.542,0.885 0.219,0.229 10 false 7 1.333,1.292 1.625,1.552 0.292,0.26 10 false 6 5.917,2.792 6.531,3.104 0.615,0.313 10 false CSW1 5.646,2.688 5.948,2.99 0.302,0.302 10 false 12 3.063,3.469 5.146,3.927 2.083,0.458 10 false Pattern Select Switch Assembly 3.49,2.938 4.635,3.26 1.146,0.323 10 false VSC OFF Switch 3.063,3.302 3.427,3.5 0.365,0.198 10 false D35 4.792,2.667 5,2.927 0.208,0.26 10 false 5 3.146,2.677 3.406,2.927 0.26,0.25 10 false 8 2.781,4.344 4.75,4.719 1.969,0.375 10 false :CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform VSC sensor neutral memorization (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if a CAN communication system DTC is output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).

Result:
Result Proceed to
DTC is not output. A
DTC is output. B




A

2.CHECK IF BRAKE ACTUATOR ASSEMBLY CONNECTOR IS SECURELY CONNECTED

B

2.CHECK IF BRAKE ACTUATOR ASSEMBLY CONNECTOR IS SECURELY CONNECTED
a.

Check if the skid control ECU (brake actuator assembly) connector is securely connected.

OK:

The connector is securely connected.




OK

3.CHECK BATTERY

NG

CONNECT CONNECTOR TO ECU CORRECTLY

3.CHECK BATTERY
a.

Check the battery voltage.

Standard Voltage:

11 to 14 V




OK

4.READ VALUE USING GTS (VSC OFF SWITCH)

NG

4.READ VALUE USING GTS (VSC OFF SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Select the Data List using the GTS (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST).

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
TRC(TRAC)/VSC Off Mode TRC/VSC OFF mode / Normal, TRC(TRAC) OFF or VSC OFF Normal: Normal mode
TRC(TRAC) OFF: TRC OFF mode
VSC OFF: VSC OFF mode
-


d.

Using the GTS, check that the switch condition displayed on the GTS changes according to VSC OFF switch operation.

OK:

The GTS display changes according to VSC OFF switch operation.




OK

5.INSPECT COMBINATION METER ASSEMBLY

NG

6.INSPECT VSC OFF SWITCH
5.INSPECT COMBINATION METER ASSEMBLY
a.

Perform an Active Test of the combination meter assembly (meter CPU) using the GTS (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).


b.

Check the combination meter assembly.

OK:

The TRC OFF indicator light turns on or off in accordance with the Active Test operation.


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE).




OK

NG

REPLACE COMBINATION METER ASSEMBLY

6.INSPECT VSC OFF SWITCH

OK

7.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - VSC OFF SWITCH)

NG

REPLACE PATTERN SELECT SWITCH ASSEMBLY

7.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - VSC OFF SWITCH)
a.

Disconnect the skid control ECU (brake actuator assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A5-12 (CSW1) - D35-5 Always Below 1 Ω
A5-12 (CSW1) - Body ground Always 10 kΩ or higher
D35-8 - Body ground Always Below 1 Ω


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE).




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR