Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM
RM2090E _54 Brake _060684 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0297617 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1231  Steering Angle Sensor  


DESCRIPTION

The steering sensor signal is sent to the skid control ECU (brake actuator assembly) via the CAN communication system. When there is a malfunction in the CAN communication system, it will be detected by the steering sensor zero point malfunction diagnostic function.

DTC Code DTC Detection Condition Trouble Area
C1231 When the +BS terminal voltage is between 9.6 and 16.5 V, the steering sensor malfunction signal is received.
·

Steering sensor

·

Steering sensor circuit

·

Steering sensor power supply



WIRING DIAGRAM

C261382E03
0.875,3.99 3.698,4.229 2.823,0.24 10 false :CAN Communication Line 0.458,2.854 1.219,3.094 0.76,0.24 10 false D56 0.438,3.021 2.396,3.365 1.958,0.344 10 false Steering Sensor 0.969,2.292 1.75,2.5 0.781,0.208 10 false ESS 1.052,1.573 1.771,1.781 0.719,0.208 10 false IG 3.969,1.573 5.396,1.844 1.427,0.271 10 false from IG1 Circuit 2.292,1.74 3.094,2.031 0.802,0.292 10 false ECU IG1 5.927,2.594 6.406,2.76 0.479,0.167 10 false A5 5.906,2.76 7.073,3.458 1.167,0.698 10 false Skid Control ECU (Brake Actuator Assembly) 1.354,2.188 1.542,2.365 0.188,0.177 10 false 1 1.354,1.458 1.542,1.635 0.188,0.177 10 false 4

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the steering sensor, perform VSC sensor neutral memorization (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:
·

When DTC U0073 and/or U0126 is output together with DTC C1231, inspect and repair the trouble areas indicated by DTC U0073 and/or U0126 first (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>U0073).

·

When the speed sensor or the yaw rate sensor has trouble, DTCs for the steering sensor may be output even when the steering sensor is normal. When DTCs for the speed sensor or yaw rate sensor assembly are output together with this steering sensor DTC, inspect and repair the speed sensor and yaw rate sensor assembly first, and then inspect and repair the steering sensor.



PROCEDURE

1.CHECK DTC

b.

Turn the ignition switch off.


c.

Turn the ignition switch to ON again and check that no CAN communication system DTC is output.


d.

Drive the vehicle at a speed of 35 km/h (22 mph), turn the steering wheel to the right and left, and check that no speed sensor and yaw rate sensor DTCs are output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
No CAN communication system, speed sensor or yaw rate sensor DTC is output. A
CAN communication system DTC is output. B
Speed sensor or yaw rate sensor DTC is output. C

HINT:
·

If there is a malfunction in the speed sensor or yaw rate sensor, an abnormal value may be output although the steering sensor is normal.

·

If speed sensor and yaw rate sensor assembly DTCs are output together with this steering sensor DTC, inspect and repair the speed and yaw rate sensors first, and then inspect and repair the steering sensor.





A

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)

B

GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

C

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)
a.

Turn the ignition switch off.


b.

Disconnect the steering sensor connector.


c.
U147138E02
1.917,2.313 1.917,3.01 true 0.427,1.896 0.76,2.177 0.333,0.281 10 false D56 0.156,0.125 0.417,0.417 0.26,0.292 10 false *a 1.823,3.031 2.052,3.188 0.229,0.156 10 false IG

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D56-4 (IG) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Steering Sensor)



OK

3.CHECK HARNESS AND CONNECTOR (GROUND TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

3.CHECK HARNESS AND CONNECTOR (GROUND TERMINAL)
a.

Turn the ignition switch off.


b.

Disconnect the steering sensor connector.


c.
U147139E02
1.333,2.313 1.333,3.01 true 0.125,0.115 0.354,0.333 0.229,0.219 10 false *a 0.417,1.906 0.781,2.146 0.365,0.24 10 false D56 1.177,3.031 1.563,3.229 0.385,0.198 10 false ESS

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D56-1 (ESS) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Steering Sensor)



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GROUND CIRCUIT)