Home › Power Source / Network › FA20 (BATTERY / CHARGING) › CHARGING SYSTEM (for 130 A Type)
RM2090E _57 Power Source / Network _060693 FA20 BATTERY / CHARGING _0297661 CHARGING SYSTEM(for 130 A Type) C

FA20 BATTERY / CHARGING  CHARGING SYSTEM(for 130 A Type)  P1530  Short in Battery Current Sensor Circuit  P1531  Open in Battery Current Sensor Circuit  P1532  Battery Current Sensor Circuit  


DESCRIPTION

A194388E15
0.094,0.198 1.531,0.51 1.438,0.313 10 false Sensor Output Voltage 0.229,0.865 0.333,1.031 0.104,0.167 10 false 5 0.229,1.208 0.333,1.375 0.104,0.167 10 false 4 0.229,1.583 0.333,1.75 0.104,0.167 10 false 3 0.229,1.927 0.333,2.094 0.104,0.167 10 false 2 0.229,2.281 0.333,2.448 0.104,0.167 10 false 1 0.229,2.656 0.333,2.823 0.104,0.167 10 false 0 0.104,1.042 0.323,1.188 0.219,0.146 10 false 4.5 0.104,1.396 0.323,1.542 0.219,0.146 10 false 3.5 0.104,1.75 0.323,1.896 0.219,0.146 10 false 2.5 0.104,2.135 0.323,2.281 0.219,0.146 10 false 1.5 0.104,2.479 0.323,2.625 0.219,0.146 10 false 0.5 0.104,0.521 0.313,0.729 0.208,0.208 10 false (V) 0.427,2.771 0.74,2.927 0.313,0.156 10 false -100 2.833,2.771 3.094,2.927 0.26,0.156 10 false 100 1.094,2.771 1.313,2.927 0.219,0.156 10 false -50 2.323,2.771 2.5,2.927 0.177,0.156 10 false 50 1.781,2.771 1.896,2.948 0.115,0.177 10 false 0 3.146,2.771 3.375,2.958 0.229,0.188 10 false (A) 1.542,3.031 2.052,3.323 0.51,0.292 10 false Current

The battery current sensor assembly installed on the negative (-) battery terminal detects the amount of current supplied from the generator.

The battery current sensor assembly changes current to voltage (at the negative (-) battery terminal) and sends it to the ECM. The ECM controls the voltage of the generator based on the signals from the battery current sensor assembly.

DTC No. DTC Detection Condition Trouble Area
P1530
·

Engine speed is 500 r/min or more, battery voltage is 10.9 V or more, and 1 second or more have elapsed after starting.

·

Battery current sensor output is less than 0.347 V, and duration of the malfunction is 0.5 seconds or more (1-trip detection logic).


·

Battery current sensor assembly

·

Open or short to GND in battery current sensor circuit

·

ECM


P1531
·

Engine speed is 500 r/min or more, battery voltage is 10.9 V or more, and 1 second or more have elapsed after starting.

·

Battery current sensor output is more than 4.653 V, and duration of the malfunction is 0.5 seconds or more (1-trip detection logic).


·

Battery current sensor assembly

·

Short to +B or VC in battery current sensor circuit

·

ECM


P1532
·

Ignition switch ON

·

Current sensor fixing diagnosis: The difference between the maximum and minimum current value when changing charging states is less than 0.07 V, and the charging state changes 10 times or more in succession when malfunctioning (1-trip detection logic).

·

Charging side properties diagnosis: After the alternator target DUTY has changed from 60% or more to less than 40%, with the alternator target DUTY is less than 40%, the battery voltage is less than 13.2 V and the battery current sensor voltage is 2.6 V or more and less than 5 V, and the duration of the malfunction is 30 seconds or more (1-trip detection logic).

·

Discharge side properties diagnosis: After the alternator target DUTY has changed from less than 40% to 60% or more, with the alternator target DUTY at 60% or more, the battery voltage is more than 13.7 V and the battery current sensor voltage is 0 V or more and less than 2.4 V and the duration of malfunction is 30 seconds or more (1-trip detection logic).


·

Battery current sensor assembly

·

Short in battery current sensor circuit

·

ECM



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO P1530, P1531, P1532)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / DTC.


e.

Read the DTC.

Result
Result Proceed to
DTC P1530, P1531 and P1532 are output A
DTC P1530, P1531, P1532 and other DTCs are output B

HINT:

If any DTCs other than P1530, P1531 and P1532 are output, troubleshoot those DTCs first.




A

2.READ VALUE USING GTS (BATTERY CURRENT)

B

2.READ VALUE USING GTS (BATTERY CURRENT)
a.

Turn all of the electrical systems (headlights, blower motor, rear defogger, etc.) off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine / Data List / Battery Current.

Result
Result Proceed to
Battery current is fixed at 0 A, or fluctuates by +/- 1 A or less between -100 and 100 A A
Battery current fluctuates between -20 and 0 A B



A

3.INSPECT BATTERY CURRENT SENSOR ASSEMBLY

B

3.INSPECT BATTERY CURRENT SENSOR ASSEMBLY
a.
A266305E06
1.646,1.281 1.938,1.823 true 2.146,1.26 2.438,1.802 true 1.271,1.271 0.979,1.813 true 0.094,0.094 0.26,0.24 0.167,0.146 10 false *a 1.979,1.792 2.313,1.948 0.333,0.156 10 false GND 2.49,1.781 2.781,1.938 0.292,0.156 10 false VIN 0.781,1.781 1.073,1.938 0.292,0.156 10 false IB

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the A11 battery current sensor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (VIN) - 3 (GND) Always 3 to 10 kΩ
1 (VIN) - 4 (IB) Always Below 0.5 kΩ
3 (GND) - 4 (IB) Always 3 to 10 kΩ


Text in Illustration
*a Component without harness connected
(Battery Current Sensor Assembly)


d.

Reconnect the cable to the negative (-) battery terminal.



OK

4.CHECK HARNESS AND CONNECTOR (BATTERY CURRENT SENSOR ASSEMBLY - ECM)

NG

REPLACE BATTERY CURRENT SENSOR ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (BATTERY CURRENT SENSOR ASSEMBLY - ECM)
a.

Disconnect the A33 and A35 ECM connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A33-11 (IB) - A11-4 (IB) Always Below 1 Ω
A35-22 (VCP2) - A11-1 (VIN) Always Below 1 Ω
A35-30 (EPA2) - A11-3 (GND) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A33-11 (IB) or A11-4 (IB) - Body ground Always 10 kΩ or higher
A35-22 (VCP2) or A11-1 (VIN) - Body ground Always 10 kΩ or higher
A35-30 (EPA2) or A11-3 (GND) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR