Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM
RM2090E _57 Power Source / Network _060695 NETWORKING _0297665 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Check CAN Bus Lines for Short Circuit (RHD Models)  


DESCRIPTION

There may be a short circuit between the V bus main lines and/or CAN branch lines when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 57 Ω.

Symptom Trouble Area
Resistance between terminals 6 (CANH) and 14 (CANL) of DLC3 is below 57 Ω.
·

Short in CAN main bus line

·

Short in CAN branch line

·

Main body ECU (network gateway ECU)

·

Combination meter assembly

·

Certification ECU (smart key ECU assembly)*1

·

ECM

·

TCM*2

·

Skid control ECU

·

Steering angle sensor (spiral cable sub-assembly)

·

Power steering ECU assembly

·

Air conditioning control assembly*3

·

Air bag ECU assembly

·

CAN No. 1 junction connector

·

CAN No. 2 junction connector



*1: w/ Entry and Start System

*2: for Automatic Transmission System

*3: for Automatic Air Conditioning System

WIRING DIAGRAM

C261304E04
1.656,0.271 2,0.448 0.344,0.177 10 false ECM 0.333,1.885 2.323,2.063 1.99,0.177 10 false NO. 1 JUNCTION CONNECTOR 5.01,0.146 6.823,0.323 1.813,0.177 10 false : CAN Main Bus Line (CANH) 5.01,0.531 6.792,0.719 1.781,0.188 10 false : CAN Main Bus Line (CANL) 5.01,0.906 6.958,1.083 1.948,0.177 10 false : CAN Branch Bus Line (CANH) 5.01,1.302 6.938,1.49 1.927,0.188 10 false : CAN Branch Bus Line (CANL) 0.333,1.708 0.635,1.865 0.302,0.156 10 false A17 0.292,4.844 2.281,5.01 1.99,0.167 10 false NO. 2 JUNCTION CONNECTOR 0.292,4.667 0.563,4.833 0.271,0.167 10 false D43 1.656,0.083 1.958,0.25 0.302,0.167 10 false A33 2.74,0.906 2.917,1.073 0.177,0.167 10 false 18 3.813,0.896 4.01,1.063 0.198,0.167 10 false 19 3.833,1.521 3.948,1.677 0.115,0.156 10 false 7 2.74,1.521 2.927,1.677 0.188,0.156 10 false 18 5.5,5.448 5.698,5.615 0.198,0.167 10 false D7 4.802,4.542 5.021,4.698 0.219,0.156 10 false BR 4.75,5.281 5.146,5.458 0.396,0.177 10 false BR-W 3.844,1.177 3.969,1.344 0.125,0.167 10 false O 2.646,1.177 2.906,1.333 0.26,0.156 10 false B-P 2.542,0.677 2.938,0.833 0.396,0.156 10 false CANL 0.813,3.177 1.177,3.333 0.365,0.156 10 false CANL 3.813,0.677 4.229,0.833 0.417,0.156 10 false CANH 0.781,2.583 1.177,2.75 0.396,0.167 10 false CANH 0.781,6 1.177,6.167 0.396,0.167 10 false CANL 0.771,5.438 1.167,5.594 0.396,0.156 10 false CANH 5.573,2.365 5.958,2.521 0.385,0.156 10 false CANL 5.583,1.781 5.979,1.938 0.396,0.156 10 false CANH 5.563,5.188 5.948,5.344 0.385,0.156 10 false CANL 5.563,4.625 5.979,4.771 0.417,0.146 10 false CANH 5.573,7.25 5.958,7.417 0.385,0.167 10 false CANL 5.563,6.667 5.969,6.823 0.406,0.156 10 false CANH 3.813,3.448 3.927,3.615 0.115,0.167 10 false 6 2.781,3.438 2.958,3.604 0.177,0.167 10 false 17 3.823,4.333 3.948,4.5 0.125,0.167 10 false 9 2.771,4.344 2.958,4.5 0.188,0.156 10 false 20 3.833,3.615 4.135,3.792 0.302,0.177 10 false W-B 2.646,3.635 2.927,3.802 0.281,0.167 10 false R-Y 3.844,4.125 3.99,4.292 0.146,0.167 10 false O 2.646,4.125 2.906,4.281 0.26,0.156 10 false B-P 1.792,2.51 1.906,2.677 0.115,0.167 10 false B 1.76,3.229 1.906,3.396 0.146,0.167 10 false W 4.417,4.615 4.542,4.781 0.125,0.167 10 false 2 4.385,5.198 4.552,5.344 0.167,0.146 10 false 13 5.365,4.615 5.479,4.781 0.115,0.167 10 false 6 5.365,5.208 5.469,5.375 0.104,0.167 10 false 7 1.271,2.583 1.396,2.74 0.125,0.156 10 false 1 1.281,3.188 1.396,3.365 0.115,0.177 10 false 7 2.26,2.573 2.375,2.74 0.115,0.167 10 false 8 2.219,3.167 2.385,3.344 0.167,0.177 10 false 19 0.094,3.427 0.375,3.594 0.281,0.167 10 false A15 0.094,3.594 1.385,3.938 1.292,0.344 10 false POWER STEERING ECU ASSEMBLY 5.49,5.625 6.979,5.979 1.49,0.354 10 false COMBINATION METER ASSEMBLY 5.51,2.646 5.792,2.823 0.281,0.177 10 false A18 4.75,1.729 5.063,1.885 0.313,0.156 10 false B-W 4.875,2.469 4.99,2.646 0.115,0.177 10 false L 4.365,1.792 4.5,1.948 0.135,0.156 10 false 5 4.354,2.385 4.552,2.563 0.198,0.177 10 false 16 5.302,1.781 5.479,1.938 0.177,0.156 10 false 29 5.302,2.375 5.469,2.531 0.167,0.156 10 false 28 5.51,2.813 5.958,2.979 0.448,0.167 10 false TCM*1 5.125,7.5 5.396,7.667 0.271,0.167 10 false D41 4.833,6.583 4.969,6.75 0.135,0.167 10 false G 4.844,7.323 4.979,7.51 0.135,0.188 10 false R 4.354,6.667 4.469,6.844 0.115,0.177 10 false 4 4.344,7.25 4.521,7.427 0.177,0.177 10 false 15 5.292,6.667 5.469,6.833 0.177,0.167 10 false 14 5.313,7.26 5.469,7.427 0.156,0.167 10 false 15 1.792,5.354 1.906,5.521 0.115,0.167 10 false P 1.76,6.083 1.958,6.25 0.198,0.167 10 false LG 1.281,5.427 1.458,5.573 0.177,0.146 10 false 14 1.281,6.01 1.458,6.167 0.177,0.156 10 false 13 2.281,5.427 2.396,5.615 0.115,0.188 10 false 3 2.229,6.021 2.396,6.198 0.167,0.177 10 false 14 0.063,6.271 0.271,6.427 0.208,0.156 10 false D5 0.052,6.438 1.958,6.792 1.906,0.354 10 false MAIN BODY ECU (NETWORK GATEWAY ECU) 5.125,7.688 7.052,8.052 1.927,0.365 10 false CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)*2 0.125,7.729 2.531,7.906 2.406,0.177 10 false *1: for Automatic Transmission System 0.125,8.042 2.021,8.24 1.896,0.198 10 false *2: w/ Entry and Start System 3.198,0.104 3.563,0.281 0.365,0.177 10 false 120Ω

C261305E04
0.375,0.354 2.344,0.531 1.969,0.177 10 false NO. 2 JUNCTION CONNECTOR 0.365,0.177 0.646,0.354 0.281,0.177 10 false D43 5.5,1.146 5.99,1.427 0.49,0.281 10 false DLC3 5.5,0.969 5.927,1.313 0.427,0.344 10 false D10 5.177,0.302 5.563,0.635 0.385,0.333 10 false 6 4.375,0.302 4.74,0.615 0.365,0.313 10 false 5 4.823,0.24 5.271,0.594 0.448,0.354 10 false B-Y 5.51,0.406 5.979,0.719 0.469,0.313 10 false CANH 5.51,0.646 5.969,0.979 0.458,0.333 10 false CANL 5.563,1.813 5.979,1.969 0.417,0.156 10 false CANH 5.604,2.385 5.979,2.563 0.375,0.177 10 false CANL 5.563,3.865 5.99,4.021 0.427,0.156 10 false CANH 5.573,4.438 5.969,4.594 0.396,0.156 10 false CANL 0.781,3.229 1.188,3.385 0.406,0.156 10 false CANH 0.792,3.813 1.167,3.979 0.375,0.167 10 false CANL 3.833,5.875 4.25,6.052 0.417,0.177 10 false CANH 2.542,5.875 2.917,6.042 0.375,0.167 10 false CANL 0.781,1.188 1.188,1.344 0.406,0.156 10 false CANH 0.792,1.75 1.167,1.927 0.375,0.177 10 false CANL 4.865,0.833 5.229,1.156 0.365,0.323 10 false LG 3.823,4.75 3.958,4.917 0.135,0.167 10 false 1 2.76,4.729 2.948,4.896 0.188,0.167 10 false 12 3.854,5.667 4.042,5.823 0.188,0.156 10 false 26 2.729,5.667 2.917,5.823 0.188,0.156 10 false 14 3.844,4.906 4.146,5.083 0.302,0.177 10 false W-B 2.656,4.906 2.917,5.073 0.26,0.167 10 false R-Y 3.844,5.448 4.063,5.625 0.219,0.177 10 false BR 2.656,5.448 2.917,5.615 0.26,0.167 10 false B-R 4.344,0.76 4.74,1.083 0.396,0.323 10 false 16 5.281,0.771 5.635,1.083 0.354,0.313 10 false 14 4.438,5.906 4.635,6.073 0.198,0.167 10 false A5 1.74,3.167 1.979,3.323 0.24,0.156 10 false P-L 1.708,3.885 2.01,4.052 0.302,0.167 10 false R-W 1.271,3.219 1.458,3.385 0.188,0.167 10 false 13 1.281,3.823 1.458,3.99 0.177,0.167 10 false 22 2.271,3.24 2.385,3.406 0.115,0.167 10 false 8 2.219,3.813 2.385,3.979 0.167,0.167 10 false 19 0.083,4.094 0.365,4.25 0.281,0.156 10 false D27 0.083,4.26 1.802,4.448 1.719,0.188 10 false AIR BAG ECU ASSEMBLY 1.698,1.125 2.01,1.281 0.313,0.156 10 false G-W 1.792,1.844 1.917,2.031 0.125,0.188 10 false G 1.271,1.198 1.583,1.5 0.313,0.302 10 false 3 1.281,1.771 1.604,2.083 0.323,0.313 10 false 2 2.281,1.177 2.396,1.344 0.115,0.167 10 false 6 2.208,1.771 2.396,1.938 0.188,0.167 10 false 17 0.083,2.031 0.375,2.198 0.292,0.167 10 false D56 0.094,2.219 2.292,2.563 2.198,0.344 10 false STEERING ANGLE SENSOR (SPIRAL CABLE SUB-ASSEMBLY) 4.427,6.073 6.323,6.417 1.896,0.344 10 false SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) 0.073,5.24 1.375,5.594 1.302,0.354 10 false *3: for Automatic Air Conditioning System 5.5,2.656 5.781,2.813 0.281,0.156 10 false D29 4.865,1.74 4.969,1.917 0.104,0.177 10 false P 4.875,2.469 4.979,2.635 0.104,0.167 10 false L 4.385,1.813 4.51,1.979 0.125,0.167 10 false 7 4.354,2.396 4.521,2.563 0.167,0.167 10 false 18 5.354,1.813 5.469,1.99 0.115,0.177 10 false 4 5.344,2.396 5.458,2.583 0.115,0.188 10 false 5 5.5,2.823 6.448,3.177 0.948,0.354 10 false PSP (OPTION CONNECTOR) 5.26,4.719 5.531,4.875 0.271,0.156 10 false D19 4.792,3.792 5.25,4.115 0.458,0.323 10 false L-W 4.813,4.51 5.208,4.823 0.396,0.313 10 false L-Y 4.354,3.854 4.542,4.021 0.188,0.167 10 false 10 4.365,4.438 4.542,4.625 0.177,0.188 10 false 21 5.313,3.865 5.49,4.021 0.177,0.156 10 false 13 5.302,4.448 5.479,4.604 0.177,0.156 10 false 12 5.26,4.875 6.875,5.219 1.615,0.344 10 false AIR CONDITIONING CONTROL ASSEMBLY*3 3.208,6.479 3.563,6.646 0.354,0.167 10 false 120Ω 0.677,6.875 2.479,7.063 1.802,0.188 10 false : CAN Main Bus Line (CANH) 0.688,7.208 2.469,7.396 1.781,0.188 10 false : CAN Main Bus Line (CANL) 3.74,6.865 5.698,7.052 1.958,0.188 10 false : CAN Branch Bus Line (CANH) 3.74,7.198 5.656,7.396 1.917,0.198 10 false : CAN Branch Bus Line (CANL)

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the ignition switch to ON, wait at least 60 seconds,

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR SHORT IN CAN BUS LINES (ECM)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
U147053E02
1.198,1.51 1.49,2.042 true 0.958,1.51 0.667,2.042 true 1.563,0.313 1.875,0.479 0.313,0.167 10 false A33 0.094,0.042 0.292,0.219 0.198,0.177 10 false *a 1.573,1.969 2,2.125 0.427,0.156 10 false CANH 0.26,1.969 0.625,2.115 0.365,0.146 10 false CANL

Disconnect the A33 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A33-19 (CANH) - A33-18 (CANL) Cable disconnected from negative (-) battery terminal 114 to 126 Ω


Text in Illustration
*a Front view of wire harness connector
(to ECM)



OK

NG

2.CHECK FOR SHORT IN CAN BUS LINES (SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY))
2.CHECK FOR SHORT IN CAN BUS LINES (SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY))
a.

Reconnect the A33 ECM connector.


b.
U147125E04
1.292,0.802 0.99,1.115 true 1.188,1.615 0.906,1.344 true 0.188,1.083 0.406,1.25 0.219,0.167 10 false A5 1.323,0.656 1.729,0.813 0.406,0.156 10 false CANL 1.219,1.563 1.646,1.708 0.427,0.146 10 false CANH 0.177,0.052 0.333,0.229 0.156,0.177 10 false *a

Disconnect the A5 skid control ECU (brake actuator assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A5-26 (CANH) - A5-14 (CANL) Cable disconnected from negative (-) battery terminal 114 to 126 Ω


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))



OK

NG

3.CHECK FOR SHORT IN CAN BUS LINES (CAN NO. 2 J/C)
3.CHECK FOR SHORT IN CAN BUS LINES (CAN NO. 2 J/C)
a.

Reconnect the A5 skid control ECU (brake actuator assembly) connector.


b.
U147050E04
1.667,1.906 1.177,3.021 true 2.448,1.896 2.958,2.281 true 2.26,1.906 2.813,2.531 true 0.75,0.635 1.323,1.521 true 0.583,0.813 1.156,1.542 true 0.427,1.031 0.958,1.542 true 0.281,1.333 0.771,1.51 true 0.906,0.448 1.49,1.521 true 1.094,0.25 1.656,1.531 true 1.896,1.917 2.448,2.833 true 2.073,1.917 2.667,2.708 true 2.531,0.583 2.094,1.521 true 2.375,0.396 1.927,1.531 true 2.74,0.76 2.281,1.521 true 2.948,0.958 2.479,1.531 true 0.75,1.906 0.323,2.146 true 0.948,1.906 0.49,2.354 true 1.125,1.917 0.625,2.521 true 1.302,1.917 0.792,2.667 true 1.5,1.917 0.99,2.802 true 1.552,0.531 1.844,0.688 0.292,0.156 10 false D43 0.104,0.052 0.271,0.24 0.167,0.188 10 false *a 0.073,1.26 0.24,1.438 0.167,0.177 10 false *b 0.104,2.073 0.292,2.26 0.188,0.188 10 false *b 0.219,0.938 0.385,1.115 0.167,0.177 10 false *c 0.365,0.719 0.531,0.896 0.167,0.177 10 false *d 0.552,0.521 0.719,0.698 0.167,0.177 10 false *e 0.698,0.323 0.865,0.5 0.167,0.177 10 false *f 0.896,0.146 1.063,0.323 0.167,0.177 10 false *g 0.313,2.333 0.5,2.521 0.188,0.188 10 false *c 0.438,2.49 0.625,2.677 0.188,0.188 10 false *d 0.646,2.646 0.833,2.833 0.188,0.188 10 false *e 0.813,2.781 1,2.969 0.188,0.188 10 false *f 1.042,3.021 1.229,3.208 0.188,0.188 10 false *g 2.375,0.219 2.542,0.396 0.167,0.177 10 false *h 2.542,0.385 2.708,0.563 0.167,0.177 10 false *i 2.729,0.583 2.896,0.76 0.167,0.177 10 false *j 2.958,0.792 3.125,0.969 0.167,0.177 10 false *k 3,2.271 3.167,2.448 0.167,0.177 10 false *k 2.844,2.5 3.01,2.677 0.167,0.177 10 false *j 2.698,2.708 2.865,2.885 0.167,0.177 10 false *i 2.479,2.885 2.646,3.063 0.167,0.177 10 false *h

Disconnect the wire harness connector from the D43 CAN No. 2 junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
D43-1 - D43-12 Cable disconnected from negative (-) battery terminal 114 to 126 Ω Skid control ECU (brake actuator assembly)
D43-2 - D43-13 Cable disconnected from negative (-) battery terminal 200 Ω or higher Combination meter assembly
D43-3 - D43-14 Cable disconnected from negative (-) battery terminal 200 Ω or higher Main body ECU (network gateway ECU)
D43-4 - D43-15 Cable disconnected from negative (-) battery terminal 200 Ω or higher Certification ECU (smart key ECU assembly)
D43-5 - D43-16 Cable disconnected from negative (-) battery terminal 1 MΩ or higher DLC3
D43-6 - D43-17 Cable disconnected from negative (-) battery terminal 200 Ω or higher Steering angle sensor (spiral cable sub-assembly)
D43-7 - D43-18 Cable disconnected from negative (-) battery terminal 1 MΩ or higher PSP (option connector)
D43-8 - D43-19 Cable disconnected from negative (-) battery terminal 200 Ω or higher Air bag ECU assembly
D43-9 - D43-20 Cable disconnected from negative (-) battery terminal 114 to 126 Ω CAN No. 1 junction connector
D43-10 - D43-21 Cable disconnected from negative (-) battery terminal 200 Ω or higher Air conditioning control assembly


Text in Illustration
*a Front view of wire harness connector
(to CAN No. 2 Junction Connector)
*b to Skid Control ECU (Brake Actuator Assembly)
*c to Combination Meter Assembly
*d to Main Body ECU (Network Gateway ECU)
*e to Certification ECU (Smart Key ECU Assembly)
*f to DLC3
*g to Steering Angle Sensor (Spiral Cable Sub-assembly)
*h to PSP (Option Connector)
*i to Air Bag ECU Assembly
*j to CAN No. 1 Junction Connector
*k to Air Conditioning Control Assembly

Result:
Result Proceed to
OK A
NG (CAN No. 1 junction connector main line) B
NG (Skid control ECU (brake actuator assembly) main line) C
NG (ECU or sensor branch line) D
NG (DLC3 branch line or PSP (option connector) branch line) E




A

REPLACE CAN NO. 2 JUNCTION CONNECTOR

B

4.CHECK FOR SHORT IN CAN BUS LINES (CAN NO. 1 J/C)

C

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 2 J/C - SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY))

D

5.CHECK FOR SHORT IN CONNECTED COMPONENT (ECU, SENSOR)

E

REPAIR OR REPLACE CAN BRANCH LINE CONNECTED TO DLC3 OR PSP (OPTION CONNECTOR)

4.CHECK FOR SHORT IN CAN BUS LINES (CAN NO. 1 J/C)
a.
U147051E02
1,0.375 1.49,1.542 true 1.5,1.906 1.01,3.052 true 2.604,0.625 2.115,1.531 true 2.094,1.896 2.583,2.802 true 2.427,0.354 1.927,1.521 true 1.906,1.906 2.406,3.052 true 1.188,0.125 1.677,1.552 true 1.698,1.896 1.208,3.302 true 0.802,0.271 0.969,0.469 0.167,0.198 10 false *b 0.802,2.99 0.979,3.177 0.177,0.188 10 false *b 2.646,0.531 2.813,0.729 0.167,0.198 10 false *e 2.615,2.771 2.781,2.979 0.167,0.208 10 false *e 2.469,0.25 2.625,0.448 0.156,0.198 10 false *d 2.448,3.01 2.615,3.208 0.167,0.198 10 false *d 1.021,0.031 1.177,0.229 0.156,0.198 10 false *c 1.021,3.198 1.177,3.396 0.156,0.198 10 false *c 1.563,0.563 1.854,0.719 0.292,0.156 10 false A17 0.104,0.073 0.292,0.25 0.188,0.177 10 false *a

Disconnect the wire harness connector from the A17 CAN No. 1 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
A17-5 - A17-16 Cable disconnected from negative (-) battery terminal 200 Ω or higher TCM
A17-6 - A17-17 Cable disconnected from negative (-) battery terminal 1 MΩ or higher CAN No. 2 junction connector
A17-7 - A17-18 Cable disconnected from negative (-) battery terminal 114 to 126 Ω ECM
A17-8 - A17-19 Cable disconnected from negative (-) battery terminal 200 Ω or higher Power steering ECU assembly


Text in Illustration
*a Front view of wire harness connector
(to CAN No. 1 Junction Connector)
*b to TCM
*c to CAN No. 2 Junction Connector
*d to ECM
*e to Power Steering ECU Assembly


Result:
Result Proceed to
OK A
NG (CAN No. 2 junction connector main line) B
NG (ECM main line) C
NG (ECU or sensor branch line) D



A

REPLACE CAN NO. 1 JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 2 J/C - CAN NO. 1 J/C)

C

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 1 J/C - ECM)

D

5.CHECK FOR SHORT IN CONNECTED COMPONENT (ECU, SENSOR)
5.CHECK FOR SHORT IN CONNECTED COMPONENT (ECU, SENSOR)
a.

Reconnect all the wire harness connectors (the A17 CAN No. 1 junction connector and D43 CAN No. 2 junction connector).


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU (or sensor) to which the short circuited branch line is connected (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU).


c.
U147249E04
2.271,0.365 1.979,0.896 true 1.896,1.49 1.604,2.031 true 1.49,0.354 1.781,0.51 0.292,0.156 10 false D10 0.083,0.063 0.25,0.229 0.167,0.167 10 false *1 2.323,0.26 2.74,0.417 0.417,0.156 10 false CANH 1.188,1.948 1.583,2.104 0.396,0.156 10 false CANL

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D10-6 (CANH) - D10-14 (CANL) Cable disconnected from negative (-) battery terminal 57 to 63 Ω


Text in Illustration
*1 DLC3


HINT:
·

If the resistance becomes normal (between 57 and 63 Ω) when the connector is disconnected from the ECU (or sensor), there may be a short in the ECU (or sensor).

·

If the resistance does not become normal (between 57 and 63 Ω) when the connector is disconnected from the ECU (or sensor), repair or replace the short circuited branch line or connector.




OK

REPLACE CORRESPONDING ECU OR SENSOR

NG

REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR BUS LINE OR CONNECTOR