Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Entry and Start System) › from 2014.05
RM2090E _58 Vehicle Interior _060696 DOOR LOCK _0297668 WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Entry and Start System) J

DOOR LOCK  WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Entry and Start System)  Only Wireless Control Function is Inoperative  


DESCRIPTION

w/o Tire Pressure Warning System

The door control receiver receives signals from the transmitter and sends these signals to the main body ECU (network gateway ECU). The main body ECU (network gateway ECU) then controls all doors by sending lock/unlock signals to each door.


w/ Tire Pressure Warning System

The door control receiver receives signals from the door control transmitter and sends these signals to the main body ECU (network gateway ECU) via the tire pressure warning ECU and receiver. The main body ECU (network gateway ECU) then controls all doors by sending lock/unlock signals to each door.


WIRING DIAGRAM

B374184E02
5.458,2.042 7.156,2.677 1.698,0.635 10 false Main Body ECU (Network Gateway ECU) 0.281,2.448 1.781,2.75 1.5,0.302 10 false Door Control Receiver 0.281,2.281 0.604,2.458 0.323,0.177 10 false H27 5.458,1.865 5.781,2.042 0.323,0.177 10 false D6 0.052,0.042 2.99,0.438 2.938,0.396 12 false w/o Tire Pressure Warning System: 1.063,1.979 1.448,2.156 0.385,0.177 10 false GND 1.479,1.885 1.625,2.063 0.146,0.177 10 false 1 1.063,1.51 1.448,1.688 0.385,0.177 10 false PRG 1.479,1.438 1.625,1.615 0.146,0.177 10 false 3 5.875,1.521 6.26,1.698 0.385,0.177 10 false PRG 5.646,1.438 5.844,1.615 0.198,0.177 10 false 6 5.875,1.042 6.26,1.219 0.385,0.177 10 false RDA 1.063,1.042 1.448,1.219 0.385,0.177 10 false RDA 1.479,0.948 1.625,1.125 0.146,0.177 10 false 2 1.188,0.583 1.458,0.76 0.271,0.177 10 false +B 1.479,0.5 1.625,0.677 0.146,0.177 10 false 5 5.646,0.948 5.844,1.125 0.198,0.177 10 false 7 4.688,0.594 5.5,0.896 0.813,0.302 10 false from Battery 2.167,0.74 2.677,0.906 0.51,0.167 10 false ECU-B

B374185E02
5.458,2.99 7.156,3.625 1.698,0.635 10 false Main Body ECU (Network Gateway ECU) 0.281,3.417 1.781,3.719 1.5,0.302 10 false Door Control Receiver 0.281,3.25 0.604,3.427 0.323,0.177 10 false H27 2.406,3.104 3.885,3.76 1.479,0.656 10 false Tire Pressure Warning ECU and Receiver 2.406,2.927 2.729,3.104 0.323,0.177 10 false H28 4.677,0.563 5.49,0.865 0.813,0.302 10 false from Battery 1.938,0.729 2.448,0.896 0.51,0.167 10 false ECU-B 5.458,2.813 5.781,2.99 0.323,0.177 10 false D6 0.073,0.073 2.698,0.469 2.625,0.396 12 false w/ Tire Pressure Warning System: 1.063,2.938 1.448,3.115 0.385,0.177 10 false GND 1.479,2.833 1.625,3.01 0.146,0.177 10 false 1 1.063,2.094 1.448,2.271 0.385,0.177 10 false PRG 2.344,1.979 2.49,2.156 0.146,0.177 10 false 9 3.667,1.479 3.813,1.656 0.146,0.177 10 false 7 3.656,1.01 3.802,1.188 0.146,0.177 10 false 1 3.667,2.427 3.813,2.604 0.146,0.177 10 false 5 3.667,2 3.813,2.177 0.146,0.177 10 false 4 1.479,1.99 1.625,2.167 0.146,0.177 10 false 3 2.531,2.531 2.906,2.708 0.375,0.177 10 false GND 3.177,2.531 3.625,2.708 0.448,0.177 10 false BPRG 3.365,1.573 3.583,1.75 0.219,0.177 10 false +B 3.375,1.104 3.594,1.281 0.219,0.177 10 false IG 3.177,2.073 3.625,2.25 0.448,0.177 10 false BRDA 2.531,2.073 2.979,2.25 0.448,0.177 10 false RPRG 2.531,1.51 2.979,1.688 0.448,0.177 10 false RRDA 5.823,2.521 6.208,2.698 0.385,0.177 10 false PRG 5.604,2.427 5.802,2.604 0.198,0.177 10 false 6 5.823,2.083 6.208,2.26 0.385,0.177 10 false RDA 1.063,1.51 1.448,1.688 0.385,0.177 10 false RDA 1.479,1.417 1.625,1.594 0.146,0.177 10 false 2 1.188,0.573 1.458,0.75 0.271,0.177 10 false +B 1.479,0.469 1.625,0.646 0.146,0.177 10 false 5 5.604,1.99 5.802,2.167 0.198,0.177 10 false 7 2.292,1.417 2.49,1.594 0.198,0.177 10 false 10 2.271,2.417 2.469,2.594 0.198,0.177 10 false 12 5,1.573 5.813,1.875 0.813,0.302 10 false from Battery 4.979,1.104 6.438,1.406 1.458,0.302 10 false from IG1 NO. 1 Relay 3.979,1.26 4.594,1.427 0.615,0.167 10 false ECU IG1 4.031,1.729 4.542,1.896 0.51,0.167 10 false MPX-B

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

When replacing or inspecting the door control receiver and wire harness, do not change the position or length of the wire harness. If the wire harness is too close to the door control receiver, wireless function performance may be affected.

·

* When replacing the tire pressure warning ECU and receiver, read the transmitter IDs stored in the old ECU using the GTS and write them down before removal.

·

* It is necessary to perform initialization after registration of the transmitter IDs into the tire pressure warning ECU and receiver if the tire pressure warning ECU and receiver has been replaced.




*: w/ Tire Pressure Warning System


PROCEDURE

1.CONFIRM VEHICLE SPECIFICATION
a.

Confirm the vehicle specification.


Result
Result Proceed to
w/ Tire Pressure Warning System A
w/o Tire Pressure Warning System B


A

2.CHECK FOR DTC (TIRE PRESSURE WARNING SYSTEM)

B

3.CHECK POWER DOOR LOCK OPERATION
2.CHECK FOR DTC (TIRE PRESSURE WARNING SYSTEM)

OK

3.CHECK POWER DOOR LOCK OPERATION

NG

3.CHECK POWER DOOR LOCK OPERATION
a.

When the door control switch on the power window regulator master switch assembly is operated, check that the locked doors unlock (See page Vehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK).


OK:

Locked doors unlock.



OK

4.CHECK KEY REMINDER WARNING SYSTEM

NG

4.CHECK KEY REMINDER WARNING SYSTEM
a.

Check that the key reminder warning buzzer operates normally (See page Vehicle Interior>DOOR LOCK>KEY REMINDER WARNING SYSTEM(w/o Entry and Start System)>OPERATION CHECK).

OK:

Key reminder warning buzzer operates normally.




OK

5.SWITCH TO SELF DIAGNOSTIC MODE

NG

5.SWITCH TO SELF DIAGNOSTIC MODE
a.

Switch to self-diagnostic mode by operating the ignition key cylinder.

i.

Insert the key into the ignition key cylinder and remove it.


ii.

Within 5 seconds after the key is removed, insert it into the ignition key cylinder and then turn the ignition switch to ON then off once. (End in off)


iii.

Within 30 seconds after turning the ignition switch off, perform the following 9 times: Turn the ignition switch to ON then off. (End in off)

NOTICE:

If the system fails to enter self-diagnostic mode, the system will return to normal mode.


HINT:

Turning the ignition switch to ON after the procedure above has been completed will end the self-diagnostic mode.




b.
B220865E09
0.125,0.031 1.521,0.375 1.396,0.344 10 Interior Light Output: 0.625,1.396 0.854,1.615 0.229,0.219 10 ON 0.573,1.708 0.875,2 0.302,0.292 10 OFF 1.531,2.167 1.76,2.385 0.229,0.219 10 T1 2.146,2.167 2.406,2.406 0.26,0.24 10 T2 1.979,2.604 3.073,2.771 1.094,0.167 10 T1: 0.25 seconds 1.979,2.917 3.073,3.104 1.094,0.188 10 T2: 0.5 seconds 1.802,2.167 2.042,2.385 0.24,0.219 10 T1

Check that the system has switched to self-diagnostic mode by checking the interior light output pattern.


c.
B220865E08
0.125,0.031 2.396,0.375 2.271,0.344 10 Wireless Door Lock Buzzer Output: 0.635,1.406 0.865,1.552 0.229,0.146 10 ON 0.583,1.698 0.885,1.844 0.302,0.146 10 OFF 1.531,2.167 1.729,2.344 0.198,0.177 10 T1 2.146,2.167 2.344,2.344 0.198,0.177 10 T2 1.969,2.583 3.146,2.75 1.177,0.167 10 T1: 0.125 seconds 1.969,2.896 3.063,3.073 1.094,0.177 10 T2: 0.5 seconds 1.802,2.167 2,2.344 0.198,0.177 10 T1

Check that the system has switched to self-diagnostic mode by checking the wireless door lock buzzer output pattern (w/ Wireless Door Lock Buzzer Control Function).


OK:

Flash pattern is same as illustration on left.



NEXT

6.CHECK BY SELF DIAGNOSTIC MODE
6.CHECK BY SELF DIAGNOSTIC MODE
a.

Check the diagnostic outputs when the door control transmitter module set sub-assembly switch is held down. The diagnostic outputs can be checked by the interior light and wireless door lock buzzer patterns.

B466957E01
0.167,0.135 3.615,0.333 3.448,0.198 10 false Interior Light and Wireless Door Lock Buzzer*1 Output: 0.25,1.083 1.365,1.333 1.115,0.25 10 false Normal Wave 4.167,0.5 6.333,0.75 2.167,0.25 10 false Unmatching Recognition Code: 0.25,1.417 4,1.667 3.75,0.25 10 false (LOCK / UNLOCK / LUGGAGE OPEN / PANIC*2 Switch): 0.469,1.969 0.833,2.219 0.365,0.25 10 false ON 0.469,2.333 0.833,2.531 0.365,0.198 10 false OFF 4.219,1.146 4.583,1.396 0.365,0.25 10 false ON 4.219,1.552 4.583,1.75 0.365,0.198 10 false OFF 4.156,3.375 4.521,3.573 0.365,0.198 10 false OFF 5,2 6.75,2.25 1.75,0.25 10 false Wave is being received 1.219,2.833 1.583,3.083 0.365,0.25 10 false T1 1.719,2.833 2.083,3.031 0.365,0.198 10 false T2 4.167,2.917 6.333,3.167 2.167,0.25 10 false No Diagnostic Output: 0.417,3.083 4.167,3.333 3.75,0.25 10 false T1: 0.25 seconds (Interior Light) 0.667,3.417 4.417,3.667 3.75,0.25 10 false 0.125 seconds (Wireless Door Lock Buzzer)*1 0.417,3.75 4.167,4 3.75,0.25 10 false T2: 0.5 seconds (Interior Light) 0.667,4.083 4.417,4.333 3.75,0.25 10 false 0.25 seconds (Wireless Door Lock Buzzer)*1 0.333,4.417 4.083,4.667 3.75,0.25 10 false *1: w/ Wireless Door Lock Buzzer Answer-back Function 4.75,4.417 7.01,4.667 2.26,0.25 10 false *2: w/ Panic Alarm Control Function

Result
Result Proceed to
Normal wave (light flash pattern and buzzer pattern) is output. A
Unmatching recognition code is output. B
No diagnosis outputs C



A

REPLACE MAIN BODY ECU (NETWORK GATEWAY ECU)

B

7.REGISTER RECOGNITION CODE

C

8.CHECK RESPONSE OF DOOR CONTROL RECEIVER (RESPONSE)
7.REGISTER RECOGNITION CODE
a.

Check that the system can be switched to rewrite mode or add mode, and that a recognition code can be registered.

OK:

Recognition code can be registered.




OK

END

NG

REPLACE DOOR CONTROL TRANSMITTER MODULE SET SUB-ASSEMBLY

8.CHECK RESPONSE OF DOOR CONTROL RECEIVER (RESPONSE)
a.

Prepare the door control transmitter from another vehicle.


b.

Press and hold down the door control transmitter switch.


c.

Check that an unmatching recognition code is output.


OK:

Unmatching recognition code is output.



OK

9.INSPECT TRANSMITTER BATTERY (VOLTAGE)

NG

12.CHECK WAVE ENVIRONMENT
9.INSPECT TRANSMITTER BATTERY (VOLTAGE)
B178438E07
1.383,0.308 1.574,0.473 0.191,0.166 10 *1 1.384,0.413 1.26,0.413 1.26,0.413 0.986,1.403 false

a.

Remove the battery from the door control transmitter module that does not operate. Attach a lead wire (0.6 mm (0.0236 in.)) or less in diameter including wire sheath) with tape or equivalent to the negative terminal (See page Vehicle Interior>DOOR LOCK>TRANSMITTER BATTERY(w/o Entry and Start System)>REPLACEMENT).

NOTICE:

Do not wrap the lead wire around the terminal, wedge it between terminals, or solder it. The terminal may be deformed or damaged, and the battery will not be able to be installed correctly.


Text in Illustration
*1 Lead Wire


b.

Carefully pull the lead wire out from the position shown in the illustration and install the previously removed transmitter battery.

NOTICE:

When replacing the transmitter battery, before starting work, remove any static electricity that has built up by touching, for example, the vehicle to prevent the door control transmitter module set from being damaged.



c.
B320719E01
1.732,0.755 1.899,0.401 1.899,0.401 1.975,0.401 false 1.989,0.293 2.168,0.460 0.179,0.167 10 *a

Measure the voltage according to the value(s) in the table below.

HINT:

When measuring the battery voltage, press one of the transmitter switches.


Standard Voltage:
Tester Connection Switch Condition Specified Condition
Battery positive (+) - Battery negative (-) Ignition switch off, all doors closed and lock or unlock switch pushed 2.5 to 3.2 V


Text in Illustration
*a GND



OK

REPLACE DOOR CONTROL TRANSMITTER MODULE SET SUB-ASSEMBLY

NG

10.REPLACE TRANSMITTER BATTERY
10.REPLACE TRANSMITTER BATTERY

NEXT

11.CHECK BY SELF DIAGNOSTIC MODE
11.CHECK BY SELF DIAGNOSTIC MODE
a.

Inspect the diagnostic outputs when the door control transmitter module set sub-assembly switch is held down. The diagnostic outputs can be checked by the flash patterns of the interior lights and the buzzer patterns of the wireless door lock buzzer.

B466957E01
0.167,0.135 3.615,0.333 3.448,0.198 10 false Interior Light and Wireless Door Lock Buzzer*1 Output: 0.25,1.083 1.365,1.333 1.115,0.25 10 false Normal Wave 4.167,0.5 6.333,0.75 2.167,0.25 10 false Unmatching Recognition Code: 0.25,1.417 4,1.667 3.75,0.25 10 false (LOCK / UNLOCK / LUGGAGE OPEN / PANIC*2 Switch): 0.469,1.969 0.833,2.219 0.365,0.25 10 false ON 0.469,2.333 0.833,2.531 0.365,0.198 10 false OFF 4.219,1.146 4.583,1.396 0.365,0.25 10 false ON 4.219,1.552 4.583,1.75 0.365,0.198 10 false OFF 4.156,3.375 4.521,3.573 0.365,0.198 10 false OFF 5,2 6.75,2.25 1.75,0.25 10 false Wave is being received 1.219,2.833 1.583,3.083 0.365,0.25 10 false T1 1.719,2.833 2.083,3.031 0.365,0.198 10 false T2 4.167,2.917 6.333,3.167 2.167,0.25 10 false No Diagnostic Output: 0.417,3.083 4.167,3.333 3.75,0.25 10 false T1: 0.25 seconds (Interior Light) 0.667,3.417 4.417,3.667 3.75,0.25 10 false 0.125 seconds (Wireless Door Lock Buzzer)*1 0.417,3.75 4.167,4 3.75,0.25 10 false T2: 0.5 seconds (Interior Light) 0.667,4.083 4.417,4.333 3.75,0.25 10 false 0.25 seconds (Wireless Door Lock Buzzer)*1 0.333,4.417 4.083,4.667 3.75,0.25 10 false *1: w/ Wireless Door Lock Buzzer Answer-back Function 4.75,4.417 7.01,4.667 2.26,0.25 10 false *2: w/ Panic Alarm Control Function

Result
Result Proceed to
Normal wave (light flash pattern and buzzer pattern) is output. A
Unmatching recognition code is output B
No diagnosis outputs



A

END (TRANSMITTER BATTERY IS DEFECTIVE)

B

REPLACE DOOR CONTROL TRANSMITTER MODULE SET SUB-ASSEMBLY

12.CHECK WAVE ENVIRONMENT
a.

Bring the transmitter near the door control receiver, and perform a wireless operation check.

OK:

Wireless functions operate normally.


HINT:
·

When the transmitter is brought near the door control receiver, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.

·

If the inspection result is that the problem only occurs in certain locations or times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.





OK

13.INSPECT DOOR CONTROL RECEIVER (POWER SOURCE, GROUND)

NG

AFFECTED BY WAVE INTERFERENCE

13.INSPECT DOOR CONTROL RECEIVER (POWER SOURCE, GROUND)
a.

Disconnect the H27 door control receiver connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.


U190178E01
0.205,0.157 0.391,0.318 0.186,0.161 10 *a 1.522,0.236 1.817,0.392 0.295,0.156 10 H27 2.137,1.489 2.268,1.907 false 2.186,1.919 2.407,2.075 0.221,0.156 10 +B 1.295,1.489 1.164,1.907 false 0.944,1.919 1.283,2.075 0.340,0.156 10 GND

Standard Voltage:
Tester Connection Condition Specified Condition
H27-5 (+B) - Body ground Always 11 to 14 V


Standard Resistance:
Tester Connection Condition Specified Condition
H27-1 (GND) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Door Control Receiver)


OK

14.INSPECT DOOR CONTROL RECEIVER (OUTPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.INSPECT DOOR CONTROL RECEIVER (OUTPUT)
a.

Reconnect the H27 door control receiver connector.


b.

Measure the voltage according to the value(s) in the table below.


U190180E01
0.218,0.128 0.404,0.289 0.186,0.161 10 *a 0.493,0.95 0.788,1.107 0.295,0.156 10 H27 1.778,1.234 1.92,1.65 false 1.788,1.668 2.129,1.825 0.341,0.156 10 RDA

Standard Voltage:
w/o Tire Pressure Warning System
Tester Connection Switch Condition Specified Condition
H27-2 (RDA) - Body ground Ignition switch off, all doors closed and door control transmitter switch off 11 to 14 V
Ignition switch off, all doors closed and door control transmitter switch on pulse generation


Text in Illustration
*a Component with harness connected
(Door Control Receiver)

Result
Result Proceed to
OK (w/o Tire Pressure Warning System) A
OK (w/ Tire Pressure Warning System) B
NG C


A

15.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (NETWORK GATEWAY ECU) - DOOR CONTROL RECEIVER)

B

19.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (NETWORK GATEWAY ECU) - TIRE PRESSURE WARNING ECU AND RECEIVER)

C

REPLACE DOOR CONTROL RECEIVER

15.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (NETWORK GATEWAY ECU) - DOOR CONTROL RECEIVER)
a.

Disconnect the D6 main body ECU (network gateway ECU) connector.


b.

Disconnect the H27 door control receiver connector.


c.

Measure the resistance according to the value(s) in the table below.


Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
D6-7 (RDA) - H27-2 (RDA) Always Below 1 Ω
D6-6 (PRG) - H27-3 (PRG) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
D6-7 (RDA) or H27-2 (RDA) - Body ground Always 10 kΩ or higher
D6-6 (PRG) or H27-3 (PRG) - Body ground Always 10 kΩ or higher



OK

16.REPLACE DOOR CONTROL RECEIVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.REPLACE DOOR CONTROL RECEIVER
a.

Replace the door control receiver with a new one (See page Vehicle Interior>DOOR LOCK>DOOR CONTROL RECEIVER>REMOVAL).



NEXT

17.REGISTER RECOGNITION CODE
17.REGISTER RECOGNITION CODE

NEXT

18.CHECK DOOR CONTROL RECEIVER (OPERATION)
18.CHECK DOOR CONTROL RECEIVER (OPERATION)
a.

Check that the doors can be locked and unlocked by using the transmitter LOCK and UNLOCK switches.


OK:

Doors can be locked and unlocked with transmitter.



OK

END (DOOR CONTROL RECEIVER IS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (NETWORK GATEWAY ECU)

19.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (NETWORK GATEWAY ECU) - TIRE PRESSURE WARNING ECU AND RECEIVER)
a.

Disconnect the D6 main body ECU (network gateway ECU) connector.


b.

Disconnect the H28 tire pressure warning ECU and receiver connector.


c.

Measure the resistance according to the value(s) in the table below.


Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
D6-7 (RDA) - H28-4 (BRDA) Always Below 1 Ω
D6-6 (PRG) - H28-5 (BPRG) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
D6-7 (RDA) or H28-4 (BRDA) - Body ground Always 10 kΩ or higher
D6-6 (PRG) or H28-5 (BPRG) - Body ground Always 10 kΩ or higher



OK

20.CHECK HARNESS AND CONNECTOR (TIRE PRESSURE WARNING ECU AND RECEIVER - DOOR CONTROL RECEIVER)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

20.CHECK HARNESS AND CONNECTOR (TIRE PRESSURE WARNING ECU AND RECEIVER - DOOR CONTROL RECEIVER)
a.

Disconnect the H28 tire pressure warning ECU and receiver connector.


b.

Disconnect the H27 door control receiver connector.


c.

Measure the resistance according to the value(s) in the table below.


Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
H28-10 (RRDA) - H27-2 (RDA) Always Below 1 Ω
H28-9 (RPRG) - H27-3 (PRG) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
H28-10 (RRDA) or H27-2 (RDA) - Body ground Always 10 kΩ or higher
H28-9 (RPRG) or H27-3 (PRG) - Body ground Always 10 kΩ or higher



OK

21.INSPECT TIRE PRESSURE WARNING ECU AND RECEIVER (POWER SOURCE, GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

21.INSPECT TIRE PRESSURE WARNING ECU AND RECEIVER (POWER SOURCE, GROUND)
a.

Disconnect the H28 tire pressure warning ECU and receiver connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.


U190295E02
1.302,1.625 1.167,1.969 1.167,1.969 1.031,1.969 true 2.208,1.625 2.344,1.969 2.344,1.969 2.49,1.969 true 1.292,1.281 1.146,0.938 1.146,0.938 0.885,0.938 true 1.625,0.208 1.917,0.365 0.292,0.156 10 false H28 0.115,0.052 0.302,0.208 0.188,0.156 10 false *a 2.552,1.885 2.927,2.063 0.375,0.177 10 false GND 0.667,0.854 0.875,1.031 0.208,0.177 10 false IG 0.75,1.896 0.979,2.073 0.229,0.177 10 false +B

Standard Voltage:
Tester Connection Condition Specified Condition
H28-1 (IG) - Body ground Ignition switch ON 11 to 14 V
H28-7 (+B) - Body ground Always 11 to 14 V


Standard Resistance:
Tester Connection Condition Specified Condition
H28-12 (GND) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Tire Pressure Warning ECU and Receiver)


OK

22.REPLACE DOOR CONTROL RECEIVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

22.REPLACE DOOR CONTROL RECEIVER
a.

Replace the door control receiver with a new one (See page Vehicle Interior>DOOR LOCK>DOOR CONTROL RECEIVER>REMOVAL).



NEXT

23.REGISTER RECOGNITION CODE
23.REGISTER RECOGNITION CODE

NEXT

24.CHECK DOOR CONTROL RECEIVER (OPERATION)
24.CHECK DOOR CONTROL RECEIVER (OPERATION)
a.

Check that the doors can be locked and unlocked by using the transmitter LOCK and UNLOCK switches.


OK:

Doors can be locked and unlocked with transmitter.



OK

END (DOOR CONTROL RECEIVER IS DEFECTIVE)

NG

25.REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER
25.REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER
a.

Replace the tire pressure warning ECU and receiver with a new one (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING RECEIVER>REMOVAL).



NEXT

26.CHECK DOOR CONTROL RECEIVER (OPERATION)
26.CHECK DOOR CONTROL RECEIVER (OPERATION)
a.

Check that the doors can be locked and unlocked by using the transmitter LOCK and UNLOCK switches.


OK:

Doors can be locked and unlocked with transmitter.



OK

END (TIRE PRESSURE WARNING ECU AND RECEIVER IS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (NETWORK GATEWAY ECU)