Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Entry Function) › from 2014.05
RM2090E _58 Vehicle Interior _060697 THEFT DETERRENT / KEYLESS ENTRY _0297680 ENTRY AND START SYSTEM(for Entry Function) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Entry Function)  Room Oscillator does not Recognize Key  


DESCRIPTION

If code verification cannot be performed in the vehicle interior, there may be problems with the communication between the vehicle (indoor electrical key oscillator (front floor) or (rear floor)) and electrical key transmitter sub-assembly, or the certification ECU (smart key ECU assembly) may be malfunctioning. When the electrical key transmitter sub-assembly is brought into the vehicle, verification of the key ID code transmitted from the electrical key transmitter sub-assembly and the key ID code stored in the certification ECU (smart key ECU assembly) is performed. If verification cannot be performed or the codes do not match, the engine switch cannot be turned on (IG) and the engine cannot be started.

When a door is unlocked and the electrical key transmitter sub-assembly is brought into the vehicle, the certification ECU (smart key ECU assembly) activates the indoor electrical key oscillator which transmits radio waves to detect the electrical key transmitter sub-assembly. If the electrical key transmitter sub-assembly recognizes that it is in the detection area, it responds with the key ID code. This information is received by the door control receiver and then sent to the certification ECU (smart key ECU assembly).

WIRING DIAGRAM

B268095E07
4.958,3.104 6.51,3.469 1.552,0.365 10 false Certification ECU (Smart Key ECU Assembly) 0.521,3.031 2.802,3.385 2.281,0.354 10 false No. 2 Indoor Electrical Key Oscillator (Rear Floor) 0.667,1.344 2.573,1.698 1.906,0.354 10 false Indoor Electrical Key Oscillator (Front Floor) 5.281,2.75 5.688,2.927 0.406,0.177 10 false CG6B 5.281,2.125 5.656,2.292 0.375,0.167 10 false CLG6 4.948,1.938 5.115,2.083 0.167,0.146 10 false 11 4.885,2.104 5.188,2.26 0.302,0.156 10 false D40 4.896,2.729 5.188,2.896 0.292,0.167 10 false D40 4.917,1.031 5.188,1.177 0.271,0.146 10 false D41 4.906,0.417 5.198,0.583 0.292,0.167 10 false D41 4.948,2.542 5.135,2.688 0.188,0.146 10 false 10 5.281,1.031 5.677,1.208 0.396,0.177 10 false CG5B 5.281,0.406 5.688,0.583 0.406,0.177 10 false CLG5 2,2.729 2.396,2.906 0.396,0.177 10 false CLGB 1.948,2.125 2.396,2.302 0.448,0.177 10 false ANTE6 2.51,2.615 2.615,2.76 0.104,0.146 10 false 3 2.5,2.01 2.604,2.156 0.104,0.146 10 false 1 2.01,1.031 2.406,1.198 0.396,0.167 10 false CLGB 1.948,0.406 2.396,0.563 0.448,0.156 10 false ANTE5 2.51,0.948 2.615,1.094 0.104,0.146 10 false 3 2.49,0.323 2.594,0.469 0.104,0.146 10 false 1 4.99,0.844 5.094,0.99 0.104,0.146 10 false 2 4.979,0.219 5.083,0.365 0.104,0.146 10 false 3 0.677,1.177 0.948,1.344 0.271,0.167 10 false D26 0.542,2.865 0.813,3.01 0.271,0.146 10 false H15

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the vehicle engine switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the vehicle type under manual mode and enter the following menus: Body Electrical / Entry While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Entry Function) uses a LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the entry and start system (for Entry Function) after confirming that the communication system is functioning properly.

·

Before replacing the certification ECU (smart key ECU assembly), refer to the entry and start system (for Entry Function) (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>PRECAUTION).

·

Indoor electrical key oscillator has an antenna coil between each two CLG terminals.



HINT:

Check that the entry cancel function, which is one of the customizing settings of the entry and start system, is not set (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>CUSTOMIZE PARAMETERS).


PROCEDURE

1.CHECK ENTRY AND START SYSTEM (FOR ENTRY FUNCTION)
a.

Check that the entry lock and unlock functions operate for each door (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).


OK:

Entry lock and unlock functions operate normally.



OK

2.CHECK ENTRY AND START SYSTEM (FOR START FUNCTION)

NG

2.CHECK ENTRY AND START SYSTEM (FOR START FUNCTION)
a.

Remove the battery of the electrical key transmitter sub-assembly (See page Vehicle Interior>DOOR LOCK>TRANSMITTER BATTERY(w/ Entry and Start System)>REPLACEMENT).


b.
B500237E01
2.313,1.375 2.542,1.375 false 0.354,1.01 0.583,1.01 false 0.563,1.354 0.792,1.354 false 2.094,1.021 2.323,1.021 false 1.146,2.396 1.375,2.396 false 1.323,2.823 1.552,2.823 false 0.323,3.979 0.552,3.979 false 0.74,4.26 0.969,4.26 false 2.01,3.885 2.24,3.885 false 2.375,4.188 2.604,4.188 false 0.125,0.146 0.5,0.458 0.375,0.313 10 false *A 0.115,1.833 0.615,2.198 0.5,0.365 10 false *B 0.125,3.135 0.594,3.49 0.469,0.354 10 false *C 0.958,2.323 1.333,2.635 0.375,0.313 10 false *1 0.156,0.948 0.531,1.26 0.375,0.313 10 false *1 0.385,1.281 0.76,1.594 0.375,0.313 10 false *2 2.135,1.302 2.51,1.615 0.375,0.313 10 false *3 1.917,0.948 2.292,1.26 0.375,0.313 10 false *1 0.125,3.917 0.5,4.229 0.375,0.313 10 false *1 1.833,3.802 2.208,4.115 0.375,0.313 10 false *1 0.552,4.177 0.927,4.49 0.375,0.313 10 false *2 1.135,2.75 1.51,3.063 0.375,0.313 10 false *4 2.188,4.125 2.563,4.438 0.375,0.313 10 false *3

With the brake pedal*1 or clutch pedal*2 depressed, hold the electrical key transmitter sub-assembly near the engine switch as shown in the illustration.

*1: for Automatic Transmission

*2: for Manual Transmission



c.

When operating the engine switch, check whether the engine starts.

HINT:
·

When the electrical key transmitter sub-assembly cannot be verified even though it is inside the detection area, the engine start check can be performed by removing the transmitter battery from the electrical key transmitter sub-assembly and holding the electrical key transmitter sub-assembly near the engine switch.

·

If the engine cannot be started when performing this inspection, the certification ECU (smart key ECU assembly), steering lock actuator assembly (steering lock ECU) or ID code box*1 may be malfunctioning.



*1: w/ ID Code Box


OK:

Engine starts.


Text in Illustration
*1 Engine Switch
*2 Electrical Key Transmitter Sub-assembly (w/o Panic Switch)
*3 Electrical Key Transmitter Sub-assembly (w/ Panic Switch)
*4 Electrical Key Transmitter Sub-assembly
*A Type A
*B Type B
*C Type C



OK

3.CHECK WAVE ENVIRONMENT

NG

3.CHECK WAVE ENVIRONMENT
a.

Install the battery to the electrical key transmitter sub-assembly (See page Vehicle Interior>DOOR LOCK>TRANSMITTER BATTERY(w/ Entry and Start System)>REPLACEMENT).


b.

Bring the electrical key transmitter sub-assembly near the indoor electrical key oscillator (front floor), and check that the engine can be started.

NOTICE:

If the key is brought within 0.2 m (0.656 ft.) of the indoor electrical key oscillator (front floor), communication is not possible.



c.

Bring the electrical key transmitter sub-assembly near the No. 2 indoor electrical key oscillator (rear floor), and check that the engine can be started*.

*: If the customize setting for Ignition Available Area is not set to All, the engine will not start. Before performing this inspection, check that All has been selected (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>CUSTOMIZE PARAMETERS).


NOTICE:

If the key is brought within 0.2 m (0.656 ft.) of the No. 2 indoor electrical key oscillator (rear floor), communication is not possible.


HINT:
·

As the effect of wave interference decreases by moving the electrical key transmitter sub-assembly close to the door control receiver, it may be possible to check whether wave interference is the cause of the problem.

·

If the problem only occurs in specific places or at specific times, wave interference may be the cause of the problem. Also, the vehicle may be have the effects of wave interference with the parts installed by the dealer. As a result, when parts have been installed by the dealer, it may be necessary to remove those parts before inspecting the vehicle.

·

There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.

·

If a tool for checking electric waves, such as a signal strength meter, is available, move around the area while observing both the LF band (used by the vehicle antenna to form the detection area) and RF band (used by the electrical key transmitter sub-assembly for transmission) to check for locations where there is wave interference.



OK:

The engine starts.




OK

AFFECTED BY WAVE INTERFERENCE

NG

4.CHECK KEY DIAGNOSTIC MODE
4.CHECK KEY DIAGNOSTIC MODE
a.

Check the following antennas in the key diagnostic mode (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).

i.
B374552E02
0.604,0.99 2.052,0.167 2.052,0.167 1.563,0.979 true 2.104,0.104 2.302,0.292 0.198,0.188 10 false *a 2.677,1.229 2.875,1.406 0.198,0.177 10 false *1

Check the indoor electrical key oscillator (front floor).

Text in Illustration
*1 Electrical Key Transmitter Sub-assembly
*a Inspection point

When the electrical key transmitter sub-assembly is at the inspection point, check that the wireless door lock buzzer sounds.


ii.
B374553E02
0.594,0.792 2.229,0.208 2.229,0.208 1.698,0.781 true 2.302,0.125 2.49,0.323 0.188,0.198 10 false *a 2.74,1.021 2.927,1.188 0.188,0.167 10 false *1

Check the No. 2 indoor electrical key oscillator (rear floor).

Text in Illustration
*1 Electrical Key Transmitter Sub-assembly
*a Inspection point

When the electrical key transmitter sub-assembly is at the inspection point, check that the wireless door lock buzzer sounds.

HINT:
·

If the buzzer sounds, it can be determined that the vehicle interior transmitters are operating normally.

·

It is possible to check which indoor electrical key oscillator (front floor or rear floor) is operating by the sounding of the buzzer.

·

If the buzzer does not sound for any indoor electrical key oscillators, the certification ECU (smart key ECU assembly) circuit may have a malfunction.



Result
Result Proceed to
Front side operation fails A
rear floor operation fails B
Front and rear operation checks are normal C




A

5.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)) - INDOOR ELECTRICAL KEY OSCILLATOR)

B

9.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)) - NO. 2 INDOOR ELECTRICAL KEY OSCILLATOR)

C

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

5.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)) - INDOOR ELECTRICAL KEY OSCILLATOR)
a.

Disconnect the D41 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the D26 indoor electrical key oscillator (front floor) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
D41-3 (CLG5) - D26-1 (ANTE5) Always Below 1 Ω
D41-2 (CG5B) - D26-3 (CLGB) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
D41-3 (CLG5) or D26-1 (ANTE5) - Body ground Always 10 kΩ or higher
D41-2 (CG5B) or D26-3 (CLGB) - Body ground Always 10 kΩ or higher




OK

6.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO INDOOR ELECTRICAL KEY OSCILLATOR (FRONT FLOOR))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO INDOOR ELECTRICAL KEY OSCILLATOR (FRONT FLOOR))
a.

Reconnect the D41 certification ECU (smart key ECU assembly) connector.


U190212E01
1.458,0.896 1.302,1.26 1.302,1.26 1.177,1.26 true 1.948,0.896 2.188,1.25 2.188,1.25 2.323,1.25 true 1.844,3.156 2.177,3.406 0.333,0.25 10 false *d 0.906,3.146 1.292,3.427 0.385,0.281 10 false *c 0.167,0.094 0.594,0.438 0.427,0.344 10 false *a 0.167,1.365 0.552,1.677 0.385,0.313 10 false *b 0.656,0.635 1.083,0.969 0.427,0.333 10 false D26 2.396,1.177 2.979,1.479 0.583,0.302 10 false CLGB 0.688,1.188 1.458,1.573 0.771,0.385 10 false ANTE5 0.24,2.271 0.74,2.604 0.5,0.333 10 false GND

Text in Illustration
*a Front view of wire harness connector
(to Indoor Electrical Key Oscillator (front floor))
*b Waveform
*c Door is open and then closed for 30 seconds
*d From approximately 30 seconds after door is closed

b.

Using an oscilloscope, check the waveform.

OK:
Tester Connection Condition Tool Setting Specified Condition
D26-1 (ANTE5) - D26-3 (CLGB) Procedure:
1.

Engine switch off

2.

Door is open

3.

Door is closed

4.

30 seconds elapse

5.

Electrical key transmitter sub-assembly not inside vehicle


2 V/DIV., 500 ms/DIV. Pulse generation
(See waveform)




OK

7.REPLACE INDOOR ELECTRICAL KEY OSCILLATOR (FRONT FLOOR)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

7.REPLACE INDOOR ELECTRICAL KEY OSCILLATOR (FRONT FLOOR)
a.

Temporarily replace the indoor electrical key oscillator (front floor) with a new or normally functioning one (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ELECTRICAL KEY OSCILLATOR(for Front Floor)>REMOVAL).



NEXT

8.CHECK KEY DIAGNOSTIC MODE
8.CHECK KEY DIAGNOSTIC MODE
a.

b.
B374552E02
0.604,0.99 2.052,0.167 2.052,0.167 1.563,0.979 true 2.104,0.104 2.302,0.292 0.198,0.188 10 false *a 2.677,1.229 2.875,1.406 0.198,0.177 10 false *1

Check the indoor electrical key oscillator (front floor).

Text in Illustration
*1 Electrical Key Transmitter Sub-assembly
*a Inspection point

When the electrical key transmitter sub-assembly is at the inspection point, check that the wireless door lock buzzer sounds.

OK:

Wireless door lock buzzer sounds.




OK

END (INDOOR ELECTRICAL KEY OSCILLATOR WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

9.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)) - NO. 2 INDOOR ELECTRICAL KEY OSCILLATOR)
a.

Disconnect the D40 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the H15 No. 2 indoor electrical key oscillator (rear floor) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
D40-11 (CLG6) - H15-1 (ANTE6) Always Below 1 Ω
D40-10 (CG6B) - H15-3 (CLGB) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
D40-11 (CLG6) or H15-1 (ANTE6) - Body ground Always 10 kΩ or higher
D40-10 (CG6B) or H15-3 (CLGB) - Body ground Always 10 kΩ or higher




OK

10.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 2 INDOOR ELECTRICAL KEY OSCILLATOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 2 INDOOR ELECTRICAL KEY OSCILLATOR)
a.

Reconnect the D40 certification ECU (smart key ECU assembly) connector.


U190213E01
1.833,3.133 2.019,3.294 0.186,0.161 10 *d 0.928,3.142 1.114,3.303 0.186,0.161 10 *c 0.167,0.089 0.353,0.250 0.186,0.161 10 *a 0.164,1.361 0.350,1.522 0.186,0.161 10 *b 0.638,0.608 0.933,0.765 0.295,0.156 10 H15 1.483,0.901 1.346,1.253 false 1.952,0.894 2.093,1.253 false 1.929,1.274 2.337,1.430 0.407,0.156 10 CLGB 1.044,1.274 1.550,1.430 0.506,0.156 10 ANTE6 0.183,2.246 0.532,2.402 0.349,0.156 10 GND

Text in Illustration
*a Front view of wire harness connector
(to No. 2 Indoor Electrical Key Oscillator (rear floor))
*b Waveform
*c Door is open and then closed for 30 seconds
*d From approximately 30 seconds after door is closed

b.

Using an oscilloscope, check the waveform.

OK:
Tester Connection Condition Tool Setting Specified Condition
H15-1 (ANTE6) - H15-3 (CLGB) Procedure:
1.

Engine switch off

2.

Door is open

3.

Door is closed

4.

30 seconds elapse

5.

Electrical key transmitter sub-assembly not inside vehicle


2 V/DIV., 500 ms/DIV. Pulse generation
(See waveform)




OK

11.REPLACE NO. 2 INDOOR ELECTRICAL KEY OSCILLATOR (REAR FLOOR)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

11.REPLACE NO. 2 INDOOR ELECTRICAL KEY OSCILLATOR (REAR FLOOR)

Temporarily replace the No. 2 indoor electrical key oscillator (rear floor) with a new or normally functioning one (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ELECTRICAL KEY OSCILLATOR(for Rear Floor)>REMOVAL).


NEXT

12.CHECK KEY DIAGNOSTIC MODE
12.CHECK KEY DIAGNOSTIC MODE
a.

Check the following antenna in the key diagnostic mode (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).

i.
B374553E02
0.594,0.792 2.229,0.208 2.229,0.208 1.698,0.781 true 2.302,0.125 2.49,0.323 0.188,0.198 10 false *a 2.74,1.021 2.927,1.188 0.188,0.167 10 false *1

Check the No. 2 indoor electrical key oscillator (rear floor).

Text in Illustration
*1 Electrical Key Transmitter Sub-assembly
*a Inspection point

When the electrical key transmitter sub-assembly is at the inspection point, check that the wireless door lock buzzer sounds.

OK:

Wireless door lock buzzer sounds.





OK

END (NO. 2 INDOOR ELECTRICAL KEY OSCILLATOR WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)