Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Entry Function) › from 2014.05
RM2090E _58 Vehicle Interior _060697 THEFT DETERRENT / KEYLESS ENTRY _0297680 ENTRY AND START SYSTEM(for Entry Function) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Entry Function)  All Door Entry Lock/Unlock Functions and Wireless Functions do not Operate  


DESCRIPTION

When the entry door lock and unlock functions and the wireless door lock and unlock functions do not operate, radio wave interference, or a malfunction in the key or signal circuit between the door control receiver and certification ECU (smart key ECU assembly) is suspected. The signal circuit is shared by the entry function and wireless door lock function.

WIRING DIAGRAM

B312716E02
5.438,0.813 5.635,0.99 0.198,0.177 10 false +B 5.156,0.615 5.26,0.76 0.104,0.146 10 false 2 5.083,2.104 5.365,2.26 0.281,0.156 10 false D40 5.083,1.667 5.365,1.823 0.281,0.156 10 false D40 5.083,1.229 5.354,1.375 0.271,0.146 10 false D40 5.083,2.542 5.354,2.688 0.271,0.146 10 false D48 5.083,0.792 5.365,0.938 0.281,0.146 10 false D48 5.167,1.042 5.344,1.229 0.177,0.188 10 false 5 5.125,2.365 5.302,2.552 0.177,0.188 10 false 11 5.115,1.927 5.292,2.115 0.177,0.188 10 false 19 5.115,1.479 5.292,1.667 0.177,0.188 10 false 17 0.417,3.083 1.781,3.271 1.365,0.188 10 false Door Control Receiver 5.438,1.229 5.75,1.396 0.313,0.167 10 false RCO 5.438,1.667 5.76,1.833 0.323,0.167 10 false RDA 1.365,1.25 1.542,1.396 0.177,0.146 10 false +5 1.188,1.677 1.552,1.844 0.365,0.167 10 false DATA 1.219,2.115 1.583,2.281 0.365,0.167 10 false RSSI 5.438,2.104 5.75,2.25 0.313,0.146 10 false RSSI 1.25,2.531 1.615,2.677 0.365,0.146 10 false GND 1.667,1.156 1.792,1.302 0.125,0.146 10 false 4 1.656,1.594 1.781,1.75 0.125,0.156 10 false 5 1.667,2.021 1.781,2.188 0.115,0.167 10 false 2 1.667,2.458 1.781,2.625 0.115,0.167 10 false 1 5.167,3 6.698,3.344 1.531,0.344 10 false Certification ECU (Smart Key ECU Assembly) 3.74,0.938 4.406,1.115 0.667,0.177 10 false AM2 NO.2 1.823,0.802 2.906,0.979 1.083,0.177 10 false from MAIN Fuse 0.417,2.917 0.698,3.063 0.281,0.146 10 false H26 5.427,2.552 5.75,2.698 0.323,0.146 10 false GND

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the vehicle engine switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the vehicle type under manual mode and enter the following menus: Body Electrical / Entry While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Entry Function) uses a LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the entry and start system (for Entry Function) after confirming that the communication system is functioning properly.

·

Before replacing the certification ECU (smart key ECU assembly), refer to the entry and start system (for Entry Function) (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>PRECAUTION).

·

Check that there are no electrical key transmitter sub-assemblies in the vehicle.

·

Before performing the inspection, check that DTC B1242 (wireless door lock control) is not output (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>DTC CHECK / CLEAR).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

When checking the entry lock operation multiple times, the lock operation may be limited to 2 consecutive operations depending on the settings. In order to perform the entry lock operation 3 or more times, an unlock operation must be performed once (any type of unlock operation is sufficient). However, only consecutive entry lock operations are limited. Using the wireless lock or other types of lock operations, it is possible to perform consecutive lock operations without this limitation.

·

After repair, confirm DTC does not reoccur by performing the "DTC Output Confirmation Operation".

·

Door control receiver has a constant voltage (5 V) supply circuit connected to terminal "+5".



PROCEDURE

1.CHECK BATTERY VOLTAGE
a.

Measure the voltage of the vehicle battery.

Standard voltage:

11 to 14 V


HINT:

It may be possible to tell whether the vehicle battery is discharged by operating the horn.

If the voltage is below 11 V, recharge or replace the vehicle battery before proceeding.




NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Open the driver door using the mechanical key built into the electrical key transmitter sub-assembly.


b.


OK

3.CHECK POWER DOOR LOCK CONTROL SYSTEM

NG

3.CHECK POWER DOOR LOCK CONTROL SYSTEM
a.

When the door control switch on the power window regulator master switch assembly on the driver door is operated, check that the doors unlock and lock according to the switch operation (See page Vehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK).

OK:

Door locks operate normally.




OK

4.CHECK ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY

NG

4.CHECK ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY
a.

Check if there are any other registered electrical key transmitter sub-assemblies.

Result
Result Proceed to
There are no other registered electrical key transmitter sub-assemblies A
There is another registered electrical key transmitter sub-assemblies B



A

5.ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY REGISTRATION (NEW ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY)

B

6.CHECK ENTRY DOOR LOCK OPERATION
5.ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY REGISTRATION (NEW ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY)
a.

Register a new electrical key transmitter sub-assembly (Refer to the Service Bulletin).



NEXT

6.CHECK ENTRY DOOR LOCK OPERATION
6.CHECK ENTRY DOOR LOCK OPERATION
a.

Using another registered electrical key transmitter sub-assembly, check if an entry lock/unlock operation can be performed twice in succession.

OK:

Entry lock/unlock operate normally.




OK

7.CHECK TRANSMITTER BATTERY

NG

9.CHECK WAVE ENVIRONMENT
7.CHECK TRANSMITTER BATTERY
a.

Check the transmitter battery level of the electrical key transmitter sub-assembly that was checked first.

i.

Press and hold the lock switch of the transmitter for 5 seconds and check the number of times that the transmitter LED illuminates.

Result
Result Proceed to
Transmitter LED does not illuminate when switch is pressed and held A
Transmitter LED illuminates 3 times or more when switch is pressed and held B
Transmitter LED illuminates once or twice but not a third time C

HINT:
·

The electrical key transmitter sub-assembly sends voltage information to the certification ECU (smart key ECU assembly) when it is being used. The certification ECU (smart key ECU assembly) displays "Yes" for the "Key Low Battery" item of the Data List when this voltage information indicates 2.4 V or less (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>DATA LIST / ACTIVE TEST)

·

Even if the transmitter battery is depleted, it is still possible to start the engine by holding the electrical key transmitter sub-assembly against the engine switch, depressing the brake pedal and pressing the engine switch.






A

8.INSPECT TRANSMITTER BATTERY (VOLTAGE)

B

REPLACE ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY

C

8.INSPECT TRANSMITTER BATTERY (VOLTAGE)
a.

Remove the transmitter battery from the electrical key transmitter sub-assembly that does not operate (See page Vehicle Interior>DOOR LOCK>TRANSMITTER BATTERY(w/ Entry and Start System)>REPLACEMENT).


b.
B500238E01
0.698,3.667 1.031,3.667 true 0.708,2.167 1.042,2.167 true 0.865,0.854 1.198,0.854 true 0.125,0.208 0.635,0.656 0.51,0.448 10 false *A 0.125,1.49 0.635,1.938 0.51,0.448 10 false *B 0.125,3.073 0.635,3.521 0.51,0.448 10 false *C 0.677,0.781 1.188,1.229 0.51,0.448 10 false *1 0.49,2.094 1,2.542 0.51,0.448 10 false *1 0.5,3.594 1.01,4.042 0.51,0.448 10 false *1

Attach a lead wire (0.60 mm (0.0236 in.) in diameter or less including wire sheath) with tape or equivalent to the negative terminal.

Text in Illustration
*1 Lead Wire
*A Type A
*B Type B
*C Type C

NOTICE:

Do not wrap the lead wire around a terminal, wedge it between terminals, or solder it. The terminal may be deformed or damaged, and the transmitter battery will not be able to be installed correctly.



c.

Carefully pull the lead wire out from the position shown in the illustration and install the previously removed transmitter battery.


d.
B500239E01
1.438,0.531 1.917,0.531 false 1.417,2.031 1.896,2.031 false 1.479,3.396 1.958,3.396 false 0.156,0.156 0.677,0.625 0.521,0.469 10 false *A 0.156,1.688 0.677,2.156 0.521,0.469 10 false *B 0.156,3.094 0.677,3.563 0.521,0.469 10 false *C 1.948,1.927 2.469,2.396 0.521,0.469 10 false *a 1.958,0.427 2.438,0.885 0.479,0.458 10 false *a 2,3.302 2.521,3.771 0.521,0.469 10 false *a

Measure the voltage of the transmitter battery.

Text in Illustration
*A Type A
*B Type B
*C Type C
*a GND

HINT:
·

When measuring the transmitter battery voltage, bring the electrical key transmitter sub-assembly within the lock entry operating range while operating the lock sensor of a door handle to perform the measurement.

·

Perform the measurement when the key is at room temperature.

·

The key sends voltage information to the certification ECU (smart key ECU assembly) when it is transmitting. When this voltage is 2.4 V or less the Data List item "Key Low Battery" displays "Yes". (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>DATA LIST / ACTIVE TEST)



Standard Voltage:
Tester Connection Switch Condition Specified Condition
Transmitter battery positive (+) - Transmitter battery negative (-) Engine switch off, all doors closed and lock sensor touched 2.5 to 3.2 V




OK

REPLACE ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY

NG

9.CHECK WAVE ENVIRONMENT
a.

Bring the electrical key transmitter sub-assembly near the door control receiver and perform a wireless and entry function operation check.

HINT:
·

When the electrical key transmitter sub-assembly is brought near the door control receiver, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.

·

If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.

·

There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.

·

If a tool for checking electric waves, such as a signal strength meter, is available, move around the area while observing both the LF band (used by the vehicle antenna to form the detection area) and RF band (used by the electrical key transmitter sub-assembly for transmission) to check for locations where there is wave interference.



OK:

Wireless and entry functions operate normally.




OK

AFFECTED BY WAVE INTERFERENCE

NG

10.READ VALUE USING GTS (ACC SW, IG SW)
10.READ VALUE USING GTS (ACC SW, IG SW)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

According to the display on the GTS, read the Data List.

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
ACC SW Engine switch on (ACC) / OFF or ON OFF: Engine switch off
ON: Engine switch on (ACC)
-
IG SW Engine switch on (IG) / OFF or ON OFF: Engine switch off
ON: Engine switch on (IG)
-



OK

11.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - BATTERY AND BODY GROUND)

NG

11.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - BATTERY AND BODY GROUND)
a.
U190215E01
0.157,0.099 0.438,0.272 0.281,0.173 10 *a 0.718,1.822 1.070,1.976 0.353,0.154 10 GND 2.839,1.15 3.058,1.323 0.219,0.173 10 +B 1.152,1.294 0.943,1.795 false 2.338,0.976 2.811,1.192 false 1.581,0.173 1.876,0.329 0.295,0.156 10 D48

Disconnect the D48 certification ECU (smart key ECU assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D48-11 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D48-2 (+B) - Body ground Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly))


d.

Reconnect the D48 certification ECU (smart key ECU assembly) connector.



OK

12.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - DOOR CONTROL RECEIVER)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - DOOR CONTROL RECEIVER)
a.

Disconnect the D40 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the H26 door control receiver connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
D40-5 (RCO) - H26-4 (+5) Always Below 1 Ω
D40-17 (RDA) - H26-5 (DATA) Always Below 1 Ω
D40-19 (RSSI) - H26-2 (RSSI) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
D40-5 (RCO) or H26-4 (+5) - Body ground Always 10 kΩ or higher
D40-17 (RDA) or H26-5 (DATA) - Body ground Always 10 kΩ or higher
D40-19 (RSSI) or H26-2 (RSSI) - Body ground Always 10 kΩ or higher




OK

13.INSPECT DOOR CONTROL RECEIVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.INSPECT DOOR CONTROL RECEIVER
a.

Reconnect the H26 door control receiver connector.


b.
U190216E02
2.031,1.125 2.365,1.677 false 0.24,0.104 0.417,0.281 0.177,0.177 10 false *a 1.583,0.344 1.875,0.521 0.292,0.177 10 false H26 2.25,1.708 2.594,1.875 0.344,0.167 10 false GND

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H26-1 (GND) - Body ground Always Below 1 Ω


Text in Illustration
*a Component with harness connected
(Door Control Receiver)



OK

14.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE DOOR CONTROL RECEIVER

14.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Reconnect the D40 certification ECU (smart key ECU assembly) connector.


b.
U190218E02
1.573,1.115 1.333,1.677 true 2.021,1.115 2.365,1.677 true 0.24,0.104 0.448,0.302 0.208,0.198 10 false *a 1.583,0.333 1.854,0.51 0.271,0.177 10 false H26 1.208,1.708 1.427,1.875 0.219,0.167 10 false +5 2.25,1.708 2.604,1.865 0.354,0.156 10 false GND

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H26-4 (+5) - H26-1 (GND) Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly switch not pressed


Below 1 V
Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly switch pressed


4.5 to 5.5 V


Text in Illustration
*a Component with harness connected
(Door Control Receiver)



OK

15.INSPECT DOOR CONTROL RECEIVER

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

15.INSPECT DOOR CONTROL RECEIVER
a.
U190217E02
1.865,1.135 1.604,1.781 true 1.385,1.125 0.99,1.781 true 2.031,1.115 2.365,1.781 true 0.24,0.104 0.448,0.302 0.208,0.198 10 false *a 1.573,0.354 1.854,0.521 0.281,0.167 10 false H26 1.438,1.802 1.813,1.958 0.375,0.156 10 true RSSI 0.74,1.802 1.135,1.958 0.396,0.156 10 false DATA 2.24,1.802 2.583,1.969 0.344,0.167 10 false GND

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H26-2 (RSSI) - H26-1 (GND) Procedure:
1.

All doors closed

2.

All doors locked

3.

Electrical key transmitter sub-assembly switch not pressed


11 to 14 V
Procedure:
1.

All doors closed

2.

All doors locked

3.

Electrical key transmitter sub-assembly switch pressed


Below 2 V
H26-5 (DATA) - H26-1 (GND) Procedure:
1.

All doors closed

2.

All doors locked

3.

Electrical key transmitter sub-assembly switch not pressed


11 to 14 V
1.

All doors closed

2.

All doors locked

3.

Electrical key transmitter sub-assembly switch pressed


11 to 14 V → Below 2 V → 11 to 14 V pulse generation output at regular interval


Text in Illustration
*a Component with harness connected
(Door Control Receiver)



OK

16.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE DOOR CONTROL RECEIVER

16.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Replace the certification ECU (smart key ECU assembly) with a new one.

NOTICE:

When the certification ECU (smart key ECU assembly) is replaced, it is also necessary to replace all registered electrical key transmitter sub-assemblies.




NEXT

17.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
17.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
a.

Check that the wireless door lock functions operate normally (See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Entry and Start System)>OPERATION CHECK).

OK:

Wireless door lock functions operate normally.




OK

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (NETWORK GATEWAY ECU)