Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function) › from 2014.05
RM2090E _58 Vehicle Interior _060697 THEFT DETERRENT / KEYLESS ENTRY _0297681 ENTRY AND START SYSTEM(for Start Function) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  Power Source Mode does not Change to ON (IG and ACC)  


DESCRIPTION

If any of the following operations are performed, the certification ECU (smart key ECU assembly) receives a signal, and changes the power source mode.

·

With the electrical key transmitter sub-assembly in the cabin, the engine switch is pressed.

·

When the transmitter battery in the electrical key transmitter sub-assembly is depleted, touch the electrical key transmitter sub-assembly to the surface of the engine switch while depressing the brake pedal*1 or clutch pedal*2.

·

When the entry cancel function is set by customize operation, touch the electrical key transmitter sub-assembly to the surface of the engine switch while depressing the brake pedal*1 or clutch pedal*2.

*1: for Automatic Transmission

*2: for Manual Transmission



HINT:

When the battery cable is disconnected and reconnected, the power source returns to the mode it was in before the battery cable was disconnected.


Related Data List and Active Test Items
Problem Symptom Data List Item Active Test Item
Power source mode does not change to on (IG) or on (ACC)
Power Source Control
·

Start Switch1

·

Start Switch2

·

Latch Circuit

·

IG1 Relay Monitor(Outside)

·

IG1 Relay Monitor(Inside)

·

IG2 Relay Monitor(Outside)

·

IG2 Relay Monitor(Inside)

·

ACC Relay Monitor

·

Power Supply Condition


Engine
·

Ignition Status


-

WIRING DIAGRAM

B314087E02
4.333,4.271 4.365,4.302 0.031,0.031 2.583,7.448 2.917,7.677 0.333,0.229 10 false GND 2.302,7.25 2.479,7.396 0.177,0.146 10 false 11 2.229,7.438 2.552,7.583 0.323,0.146 10 false D48 2.323,2.042 2.5,2.198 0.177,0.156 10 false 9 3.521,0.677 3.667,0.854 0.146,0.177 10 false 2 2.229,2.208 2.521,2.365 0.292,0.156 10 false D48 3.438,0.844 3.719,1 0.281,0.156 10 false D48 3.167,0.854 3.396,1.01 0.229,0.156 10 false +B 4.646,0.417 5.344,0.604 0.698,0.188 10 false AM2 NO.2 5.656,0.26 6.698,0.438 1.042,0.177 10 false from MAIN Fuse 2.167,7.969 3.677,8.333 1.51,0.365 10 false Certification ECU (Smart Key ECU Assembly) 2.594,2.229 3,2.375 0.406,0.146 10 false IG2D 1.125,2.479 1.5,2.635 0.375,0.156 10 false IG2 0.833,2.125 1,2.333 0.167,0.208 10 false 1 0.813,1.719 0.979,1.927 0.167,0.208 10 false 3 1.594,2.125 1.781,2.333 0.188,0.208 10 false 2 1.583,1.729 1.75,1.938 0.167,0.208 10 false 5 2.302,3.583 2.479,3.729 0.177,0.146 10 false 24 2.302,3.156 2.5,3.323 0.198,0.167 10 false 30 2.292,2.719 2.479,2.885 0.188,0.167 10 false 28 1.104,3.771 1.49,3.927 0.385,0.156 10 false AGND 1.094,3.344 1.49,3.51 0.396,0.167 10 false SSW2 1.083,2.938 1.479,3.115 0.396,0.177 10 false SSW1 2.594,3.344 3,3.5 0.406,0.156 10 false SSW2 2.583,2.885 2.99,3.063 0.406,0.177 10 false SSW1 2.573,3.75 2.979,3.906 0.406,0.156 10 false AGND 2.25,3.76 2.563,3.917 0.313,0.156 10 false D41 2.25,3.344 2.563,3.51 0.313,0.167 10 false D41 2.25,2.906 2.563,3.052 0.313,0.146 10 false D41 0.594,4.281 1.49,4.469 0.896,0.188 10 false Engine Switch 0.604,4.125 0.906,4.281 0.302,0.156 10 false D25 1.594,3.688 1.771,3.844 0.177,0.156 10 false 6 1.573,3.26 1.75,3.438 0.177,0.177 10 false 1 1.583,2.802 1.76,2.948 0.177,0.146 10 false 5 2.271,0.656 2.479,0.802 0.208,0.146 10 false 10 2.219,0.844 2.542,1 0.323,0.156 10 false D48 2.573,0.833 3.094,1 0.521,0.167 10 false CLUT*2 0.333,1.25 2.208,1.448 1.875,0.198 10 false Clutch Start Switch Assembly 1.615,0.76 1.75,0.917 0.135,0.156 10 false 2 0.854,0.76 1,0.917 0.146,0.156 10 false 1 0.333,1.083 0.635,1.271 0.302,0.188 10 false A20 0.281,7.177 0.698,7.344 0.417,0.167 10 false STOP 1.01,7.031 1.948,7.208 0.938,0.177 10 false from ALT Fuse 2.292,4.594 2.469,4.74 0.177,0.146 10 false 18 2.229,4.771 2.552,4.927 0.323,0.156 10 false D48 2.594,4.771 3.083,4.99 0.49,0.219 10 false STP1* 0.854,5.635 1.604,5.813 0.75,0.177 10 false Noise Filter 0.875,5.469 1.177,5.625 0.302,0.156 10 false A13 0.5,6.667 2.271,6.854 1.771,0.188 10 false Stop Light Switch Assembly 1.635,6.125 1.781,6.302 0.146,0.177 10 false 1 0.854,6.125 0.958,6.271 0.104,0.146 10 false 2 0.521,6.5 0.792,6.656 0.271,0.156 10 false A22 3.5,1.583 3.667,1.781 0.167,0.198 10 false 6 3.042,1.76 3.365,1.906 0.323,0.146 10 false IG1D 3.417,1.75 3.698,1.917 0.281,0.167 10 false D41 3.969,1.563 4.177,1.729 0.208,0.167 10 false 15 3.969,1.75 4.177,1.917 0.208,0.167 10 false 3A 4,1.167 4.146,1.313 0.146,0.146 10 false 1 3.958,1.323 4.167,1.49 0.208,0.167 10 false 3E 5.74,1.5 6.313,1.667 0.573,0.167 10 false ECU IG1 6.469,4.198 6.583,4.375 0.115,0.177 10 false 3 6.427,4.406 6.656,4.604 0.229,0.198 10 false 3A 6.438,6.792 6.667,6.938 0.229,0.146 10 false 12 6.427,6.958 6.635,7.115 0.208,0.156 10 false 3A 6.438,6.24 6.604,6.385 0.167,0.146 10 false 10 6.417,6.427 6.646,6.583 0.229,0.156 10 false 3A 6.427,5.24 6.656,5.438 0.229,0.198 10 false 28 6.427,5.417 6.656,5.594 0.229,0.177 10 false 3B 6.417,3.208 6.646,3.417 0.229,0.208 10 false 32 6.427,3.396 6.656,3.604 0.229,0.208 10 false 3A 6.438,2.177 6.667,2.344 0.229,0.167 10 false 34 6.427,2.365 6.656,2.521 0.229,0.156 10 false 3C 6.438,1.177 6.667,1.354 0.229,0.177 10 false 35 6.427,1.354 6.656,1.521 0.229,0.167 10 false 3C 4.979,7.188 5.396,7.354 0.417,0.167 10 false ACC2 4.969,6.073 5.396,6.281 0.427,0.208 10 false ACC1 4.844,5.042 5.542,5.281 0.698,0.24 10 false IG1 NO.4 4.833,4.021 5.448,4.219 0.615,0.198 10 false IG1 NO.3 4.854,3 5.469,3.198 0.615,0.198 10 false IG1 NO.2 4.854,1.979 5.469,2.146 0.615,0.167 10 false IG1 NO.1 5.885,2.51 6.167,2.708 0.281,0.198 10 false DRL 5.771,4.542 6.354,4.896 0.583,0.354 10 false SEAT HTR RH 5.781,6.573 6.302,6.885 0.521,0.313 10 false P/POINT NO.1 5.771,5.552 6.406,5.76 0.635,0.208 10 false ECU ACC 5.771,3.552 6.333,3.75 0.563,0.198 10 false HEATER 3.521,5.656 3.688,5.844 0.167,0.188 10 false 4 2.969,5.844 3.365,6.021 0.396,0.177 10 false ACCD 3.417,5.823 3.729,6 0.313,0.177 10 false D41 3.979,5.656 4.167,5.844 0.188,0.188 10 false 20 3.979,5.833 4.24,6.01 0.26,0.177 10 false 3A 3.958,7.594 6.604,7.792 2.646,0.198 10 false Instrument Panel Junction Block Assembly 0.083,8.5 1.813,8.677 1.729,0.177 10 false *2: for Manual Transmission 0.083,8.167 2.021,8.354 1.938,0.188 10 false *1: for Automatic Transmission 0.781,4.667 0.917,4.833 0.135,0.167 10 false 3 1.708,4.667 1.833,4.833 0.125,0.167 10 false 4 0.771,5.115 0.906,5.26 0.135,0.146 10 false 1 1.708,5.115 1.833,5.26 0.125,0.146 10 false 2

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the vehicle engine switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the vehicle type under manual mode and enter the following menus: Body Electrical / Entry While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system uses multiplex communication. First perform the inspections in "How to Proceed with Troubleshooting" to confirm that there are no communication malfunctions before proceeding with troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

Before replacing the certification ECU (smart key ECU assembly), refer to the entry and start system (for Entry Function) (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>PRECAUTION).

·

Make sure that no DTCs are output. If any DTCs are output, proceed to the Diagnostic Trouble Code Chart (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>DTC CHECK / CLEAR).

·

If the entry and start system is disabled through the customize function, enable the system before performing troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>CUSTOMIZE PARAMETERS).

·

After completing repairs, confirm that the problem does not reoccur.

·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM (OPERATION)
a.

Check that the wireless door lock function operates normally (See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Entry and Start System)>OPERATION CHECK).


OK:

Wireless door lock functions operate normally.



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE)

NG

GO TO ENTRY AND START SYSTEM (ALL DOOR ENTRY LOCK/UNLOCK FUNCTIONS AND WIRELESS FUNCTIONS DO NOT OPERATE)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE)

OK

3.CHECK HARNESS AND CONNECTOR (GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR IN CIRCUIT CONNECTED TO POWER SOURCE

3.CHECK HARNESS AND CONNECTOR (GROUND)

OK

4.CHECK ENTRY AND START SYSTEM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK ENTRY AND START SYSTEM
a.

Remove the battery of the electrical key transmitter sub-assembly (See page Vehicle Interior>DOOR LOCK>TRANSMITTER BATTERY(w/ Entry and Start System)>REPLACEMENT).


b.
B500237E01
2.313,1.375 2.542,1.375 false 0.354,1.01 0.583,1.01 false 0.563,1.354 0.792,1.354 false 2.094,1.021 2.323,1.021 false 1.146,2.396 1.375,2.396 false 1.323,2.823 1.552,2.823 false 0.323,3.979 0.552,3.979 false 0.74,4.26 0.969,4.26 false 2.01,3.885 2.24,3.885 false 2.375,4.188 2.604,4.188 false 0.125,0.146 0.5,0.458 0.375,0.313 10 false *A 0.115,1.833 0.615,2.198 0.5,0.365 10 false *B 0.125,3.135 0.594,3.49 0.469,0.354 10 false *C 0.958,2.323 1.333,2.635 0.375,0.313 10 false *1 0.156,0.948 0.531,1.26 0.375,0.313 10 false *1 0.385,1.281 0.76,1.594 0.375,0.313 10 false *2 2.135,1.302 2.51,1.615 0.375,0.313 10 false *3 1.917,0.948 2.292,1.26 0.375,0.313 10 false *1 0.125,3.917 0.5,4.229 0.375,0.313 10 false *1 1.833,3.802 2.208,4.115 0.375,0.313 10 false *1 0.552,4.177 0.927,4.49 0.375,0.313 10 false *2 1.135,2.75 1.51,3.063 0.375,0.313 10 false *4 2.188,4.125 2.563,4.438 0.375,0.313 10 false *3

With the brake pedal*1 or clutch pedal*2 depressed, hold the electrical key transmitter sub-assembly near the engine switch as shown in the illustration.

*1: for Automatic Transmission

*2: for Manual Transmission



c.

When touch the logo of the electrical key transmitter sub-assembly to the engine switch, check whether the power source mode changes.

OK:

Power source mode changes.


HINT:

If the power source mode changes, the cabin verification is malfunctioning.


Result
Result Proceed to
NG (Power source mode does not change) A
OK (Power source mode changes) B

Text in Illustration
*1 Engine Switch
*2 Electrical Key Transmitter Sub-assembly (w/o Panic Switch)
*3 Electrical Key Transmitter Sub-assembly (w/ Panic Switch)
*4 Electrical Key Transmitter Sub-assembly
*A Type A
*B Type B
*C Type C



A

5.READ VALUE USING GTS (STOP LIGHT SWITCH1, NEUTRAL SW/CLUTCH SW)

B

13.READ VALUE USING GTS (START SWITCH 1, 2)
5.READ VALUE USING GTS (STOP LIGHT SWITCH1, NEUTRAL SW/CLUTCH SW)
a.

for Automatic Transmission

i.

Connect the GTS to the DLC3.


ii.

Turn the engine switch on (IG).


iii.

Turn the GTS on.


iv.

Enter the following menus: Body Electrical / Power Source Control / Data List.


v.

According to the display on the GTS tester, read the Data List.

Power Source Control
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Stop Light Switch1 State of brake pedal / OFF or ON OFF: Brake pedal released
ON: Brake pedal depressed
·

Use this item to determine whether the stop light switch is malfunctioning.

·

The engine cannot be started when this item is "OFF".

·

When this item is malfunctioning, the engine can be started by pressing and holding the engine switch for a certain period of time.



OK:

ON (brake pedal depressed) and OFF (brake pedal released) appear on the screen according to the stop light switch condition.




b.

for Manual Transmission

i.

Connect the GTS to the DLC3.


ii.

Turn the engine switch on (IG).


iii.

Turn the GTS on.


iv.

Enter the following menus: Body Electrical / Power Source Control / Data List.


v.

According to the display on the GTS, read the Data List.

Power Source Control
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Neutral SW / Clutch SW State of clutch pedal / OFF or ON OFF: Clutch pedal released
ON: Clutch pedal depressed
·

Use this item to help determine if the clutch switch is malfunctioning.

·

The engine cannot be started when this item is "OFF".



OK:

ON (clutch pedal depressed) and OFF (clutch pedal released) appear on the screen according to the stop light switch condition.


Result
Result Proceed to
OK A
NG (for Automatic Transmission) B
NG (for Manual Transmission) C




A

6.READ VALUE USING GTS (POWER SUPPLY CONDITION)

B

8.INSPECT STOP LIGHT SWITCH ASSEMBLY

C

10.INSPECT CLUTCH START SWITCH ASSEMBLY
6.READ VALUE USING GTS (POWER SUPPLY CONDITION)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Power Source Control / Data List.


e.

According to the display on the GTS, read the Data List.

Power Source Control
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Power Supply Condition Power Supply Condition / All OFF, IG1 ON or ACC ON, IG2 ON, ST ON, All OFF: Engine switch off (ACC and IG)
ACC ON: Engine switch on (ACC))
IG1 ON: Engine switch on (IG) (IG1 relay on)
IG2 ON: Engine switch on (IG) (IG2 relay on)
ST ON: Sending engine start request signal
Since IG1 ON and IG2 ON turn on at approximately the same time, IG1 ON may not be displayed (IG1 ON turns on for a very short time).

OK:

Display changes according to the changes in the power source mode when the engine switch is pushed.




OK

7.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

12.CHECK FOR DTC
7.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Power Source Control / Data List.


e.

According to the display on the GTS, read the Data List.

Power Source Control
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Power Supply Condition Power Supply Condition / All OFF, IG ON or ACC ON, IG2 ON, ST ON, All OFF: Engine switch off (ACC and IG)
ACC ON: Engine switch on (ACC))
IG1 ON: Engine switch on (IG) (IG1 relay on)
IG2 ON: Engine switch on (IG) (IG2 relay on)
ST ON: Sending engine start request signal
Since IG1 ON and IG2 ON turn on at approximately the same time, IG1 ON may not be displayed (IG1 ON turns on for a very short time).


f.

Measure the voltage according to the value(s) in the table below.

U190189E01
0.19,0.15 0.376,0.311 0.186,0.161 10 *a 4.805,0.934 5.100,1.090 0.295,0.156 10 D41 2.187,0.932 2.482,1.088 0.295,0.156 10 D48 4.544,1.629 4.802,2.287 false 4.388,1.629 4.13,2.287 false 1.978,1.736 1.762,2.287 false 4.642,2.312 5.056,2.468 0.414,0.156 10 ACCD 3.927,2.312 4.290,2.468 0.363,0.156 10 IG1D 1.531,2.313 1.893,2.469 0.363,0.156 10 IG2D

Text in Illustration
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
- -

Standard Voltage:
Tester Connection Switch Condition Specified Condition
D41-6 (IG1D) - Body ground Engine switch off 1 V or less
Engine switch on (ACC) 1 V or less
Engine switch on (IG) 9 V or higher
D48-9 (IG2D) - Body ground Engine switch off 1 V or less
Engine switch on (ACC) 1 V or less
Engine switch on (IG) 9 V or higher
D41-4 (ACCD) - Body ground Engine switch off 1 V or less
Engine switch on (ACC) 8.5 V or higher
Engine switch on (IG) 8.5 V or higher




OK

CHECK RELAY CONTACT SIDE CIRCUIT

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

8.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Remove the stop light switch assembly (See page Vehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>REMOVAL).


b.

Inspect the stop light switch assembly (See page Vehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSPECTION).



OK

9.CHECK HARNESS AND CONNECTOR (NOISE FILTER - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

9.CHECK HARNESS AND CONNECTOR (NOISE FILTER - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))

OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.INSPECT CLUTCH START SWITCH ASSEMBLY
a.

Remove the clutch start switch assembly.



b.

Inspect the clutch start switch assembly.



Result
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C


A

11.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - CLUTCH START SWITCH ASSEMBLY)

B

REPLACE CLUTCH START SWITCH ASSEMBLY

C

REPLACE CLUTCH START SWITCH ASSEMBLY

11.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - CLUTCH START SWITCH ASSEMBLY)
a.

Disconnect the D48 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the A20 clutch start switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
D48-10 (CLUT) - A20-2 Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
D48-10 (CLUT) - Body ground Always 10 kΩ or higher



d.

Reconnect the A20 clutch start switch assembly connector.


U190192E01
0.078,0.027 0.263,0.189 0.186,0.161 10 *a 0.537,1.329 0.833,1.485 0.295,0.156 10 D48 1.415,1.473 1.333,1.87 false 1.106,1.895 1.505,2.051 0.399,0.156 10 CLUT

e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D48-10 (CLUT) - Body ground Clutch pedal released → clutch pedal depressed Below 1 V → 9 V or higher


Text in Illustration
*a Rear view of wire harness connector
(to certification ECU (smart key ECU assembly))



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK FOR DTC
a.

Check the DTCs (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is not output A
DTC B2784 is output B
DTC B2785 is output C



A

REPLACE ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY

B

C

13.READ VALUE USING GTS (START SWITCH 1, 2)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Power Source Control / Data List.


e.

According to the display on the GTS, read the Data List.

Power Source Control
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Start Switch 1 Condition of engine switch contact 1 / OFF or ON OFF: Engine switch not pushed
ON: Engine switch pushed
·

If the engine switch is pressed for a short time, the display may not change.

·

Use this item to determine whether the engine switch input signal is malfunctioning.


Start Switch 2 Condition of engine switch contact 2 / OFF or ON OFF: Engine switch not pushed
ON : Engine switch pushed
·

Backup for engine switch 1. However, when the engine switch is pressed and held, the control functions only when both engine switch 1 and 2 are normal.

·

Behaves the same way as engine switch 1.



OK:

The ECU data monitor changes in response to the operation of the engine switch.


Result
Result Proceed to
NG A
OK B



A

14.INSPECT ENGINE SWITCH

B

GO TO ENTRY AND START SYSTEM (FOR ENTRY FUNCTION) (ROOM OSCILLATOR DOES NOT RECOGNIZE KEY)

14.INSPECT ENGINE SWITCH
a.

Remove the engine switch (See page Engine / Hybrid System>FA20 STARTING>ENGINE SWITCH>REMOVAL).


b.


OK

15.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ENGINE SWITCH)

NG

15.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ENGINE SWITCH)
a.

Disconnect the D41 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the D25 engine switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
D41-28 (SSW1) - D25-5 (SSW1) Always Below 1 Ω
D41-30 (SSW2) - D25-1 (SSW2) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
D41-28 (SSW1) or D25-5 (SSW1) - Body ground Always 10 kΩ or higher
D41-30 (SSW2) or D25-1 (SSW2) - Body ground Always 10 kΩ or higher




OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR