Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Entry Function) › 2012.03–2014.05
RM2090E _58 Vehicle Interior _060697 THEFT DETERRENT / KEYLESS ENTRY _0297680 ENTRY AND START SYSTEM(for Entry Function) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Entry Function)  Luggage Compartment Door Entry Unlock Function does not Operate when Key is Outside Luggage Compartment  


DESCRIPTION

If the luggage compartment door entry unlock function does not operate, the request code may not be being transmitted from the luggage compartment door. If the entry functions for other doors operate properly, communication between the electrical key transmitter sub-assembly and door control receiver is normal. In this case, there may be a problem with request code transmission (communication between the certification ECU (smart key ECU assembly) and electrical key antenna (outside luggage)), a luggage compartment door outer switch malfunction or wave interference.

WIRING DIAGRAM

B312721E02
4.104,0.323 4.25,0.49 0.146,0.167 10 false 2 3.677,0.323 4.052,0.479 0.375,0.156 10 false ANT2 4.104,0.719 4.229,0.865 0.125,0.146 10 false 1 5.271,0.438 5.688,0.604 0.417,0.167 10 false CG8B 5.281,0.833 5.698,1.042 0.417,0.208 10 false CLG8 4.906,0.438 5.188,0.594 0.281,0.156 10 false D40 4.948,1.719 5.125,1.875 0.177,0.156 10 false 27 4.885,1.917 5.167,2.063 0.281,0.146 10 false D40 4.906,0.813 5.208,0.969 0.302,0.156 10 false D40 4.99,0.25 5.125,0.396 0.135,0.146 10 false 1 4.99,0.625 5.146,0.771 0.156,0.146 10 false 2 5.24,1.896 5.656,2.073 0.417,0.177 10 false TSW5 3.677,0.719 4.031,0.865 0.354,0.146 10 false ANT1 1.333,1.365 3.896,1.563 2.563,0.198 10 false Electrical Key Antenna (Outside Luggage) 1.333,1.198 1.521,1.344 0.188,0.146 10 false H3 2.167,2.417 3.781,2.771 1.615,0.354 10 false Back Door Opener Switch Assembly 2.167,2.25 2.344,2.406 0.177,0.156 10 false J2 2.354,4.458 2.49,4.604 0.135,0.146 10 false 3 2.063,4.49 2.302,4.656 0.24,0.167 10 false D+ 2.354,4.083 2.49,4.24 0.135,0.156 10 false 1 2.135,4.073 2.24,4.219 0.104,0.146 10 false B 0.927,4.073 1.052,4.219 0.125,0.146 10 false E 0.76,4.073 0.896,4.24 0.135,0.167 10 false 2 0.594,4.906 0.833,5.052 0.24,0.146 10 false J3 0.594,5.063 2.542,5.26 1.948,0.198 10 false Luggage Door Closer Assembly 5.271,4.146 5.594,4.323 0.323,0.177 10 false TR+ 4.958,3.99 5.115,4.135 0.156,0.146 10 false 4 3.698,3.99 3.802,4.135 0.104,0.146 10 false 6 3.667,4.406 3.844,4.552 0.177,0.146 10 false 26 4.927,4.385 5.104,4.531 0.177,0.146 10 false 12 3.531,5.021 5.146,5.375 1.615,0.354 10 false Instrument Panel Junction Block Assembly 4.833,6 6.417,6.365 1.583,0.365 10 false Main Body ECU (Network Gateway ECU) 4.833,2.667 6.354,3.031 1.521,0.365 10 false Certification ECU (Smart Key ECU Assembly) 0.844,6.333 2.583,6.51 1.74,0.177 10 false : CAN Communication Line 4.906,4.156 5.156,4.323 0.25,0.167 10 false MB 3.656,4.156 3.896,4.333 0.24,0.177 10 false 3B 3.667,4.583 3.906,4.771 0.24,0.188 10 false 3D 4.906,4.552 5.167,4.719 0.26,0.167 10 false MB 2.146,1.802 2.281,1.958 0.135,0.156 10 false 1 3.219,1.802 3.344,1.948 0.125,0.146 10 false 2

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off to troubleshoot:

Connect the GTS to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the GTS and vehicle begins.

·

The entry and start system (for Entry Function) uses the CAN communication system and LIN communication system. First inspect the communication systems by following How to Proceed with Troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

·

Check that there are no electrical key transmitter sub-assemblies in the vehicle.

·

Before performing the inspection, check that DTC B1242 (wireless door lock control) is not output (See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Entry and Start System)>DTC CHECK / CLEAR).

·

Before replacing the certification ECU (smart key ECU assembly), refer to the entry and start system (for Entry Function) precaution (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>PRECAUTION).

·

After repair, confirm that no DTCs are output by performing the "DTC Output Confirmation Operation".



PROCEDURE

1.READ VALUE USING GTS (TRUNK OPEN MODE)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Entry&Start / Data List.


e.

Read the Data List according to the display on the GTS.

Entry&Start
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Trunk Open Mode Back door opener switch assembly / ON or OFF Customization status displayed -

Result:
Result Proceed to
Entry luggage compartment door open mode is ON A
Entry luggage compartment door open mode is OFF B




A

2.READ VALUE USING GTS (TR/B-DOOR UNLOCK SW)

B

2.READ VALUE USING GTS (TR/B-DOOR UNLOCK SW)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Entry&Start / Data List.


e.

Read the Data List according to the display on the GTS.

Entry&Start
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Tr/B-Door Unlock SW Back door opener switch assembly / ON or OFF ON: Back door opener switch assembly pushed
OFF: Back door opener switch assembly not pushed
-

OK:

On the GTS screen, the display changes between ON and OFF according to the chart above.




OK

3.PERFORM ACTIVE TEST USING GTS

NG

8.INSPECT BACK DOOR OPENER SWITCH ASSEMBLY
3.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Active Test.


e.

Read the Data List according to the display on the GTS.

Main Body
Tester Display Test Part Control Range Diagnostic Note
Trunk and Back-door Open Operate luggage door closer assembly motor ON/OFF -

OK:

Luggage door closer assembly motor operates.




OK

4.CHECK WAVE ENVIRONMENT

NG

10.INSPECT LUGGAGE DOOR CLOSER ASSEMBLY
4.CHECK WAVE ENVIRONMENT
a.
B311619E01
1.764,1.212 1.936,1.381 0.173,0.169 10 *a

Bring the electrical key transmitter sub-assembly near the electrical key antenna (outside luggage), and perform an entry luggage compartment open function check.

Text in Illustration
*a Approximately 0.3 m (0.984 ft.)

NOTICE:

If the electrical key transmitter sub-assembly is brought within 0.2 m (0.656 ft.) of the rear bumper, communication is not possible.


HINT:
·

When pressing the luggage compartment door opener outer switch, hold the electrical key transmitter sub-assembly approximately 1 m (3.28 ft.) above the ground and approximately 0.3 m (0.984 ft.) away from the vehicle as shown in the illustration.

·

When the electrical key transmitter sub-assembly is brought near the electrical key antenna (outside luggage), the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.

·

If the operation check is normal, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.



OK:

Entry functions operate normally.




OK

AFFECTED BY WAVE INTERFERENCE

NG

5.CHECK KEY DIAGNOSTIC MODE
5.CHECK KEY DIAGNOSTIC MODE
a.

B311619E01
1.764,1.212 1.936,1.381 0.173,0.169 10 *a

Text in Illustration
*a 0.7 to 1.0 m (2.30 to 3.28 ft.)

b.

When the electrical key transmitter sub-assembly is held at the same height as the rear bumper upper surface, align it with the center of the rear of the vehicle and check that the wireless door lock buzzer sounds.

HINT:
·

Hold the electrical key transmitter sub-assembly at the same height as the rear bumper upper surface and align it with the center of the rear of the vehicle (0.7 to 1.0 m (2.30 to 3.28 ft.)). Make sure that the direction of the electrical key transmitter sub-assembly is as shown in the illustration.

·

If the buzzer sounds, it can be determined that the luggage compartment exterior transmitter is operating normally.



OK:

Wireless door lock buzzer sounds.




OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

6.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - ELECTRICAL KEY ANTENNA)
6.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - ELECTRICAL KEY ANTENNA)
a.

Disconnect the D40 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the H3 electrical key antenna (outside luggage) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D40-1 (CG8B) - H3-2 (ANT2) Always Below 1 Ω
D40-2 (CLG8) - H3-1 (ANT1) Always Below 1 Ω
D40-1 (CG8B) - Body ground Always 10 kΩ or higher
D40-2 (CLG8) - Body ground Always 10 kΩ or higher




OK

7.INSPECT ELECTRICAL KEY ANTENNA (OUTSIDE LUGGAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT ELECTRICAL KEY ANTENNA (OUTSIDE LUGGAGE)
a.
B226391E30
2.298,0.98 2.722,1.155 0.424,0.174 10 ANT2 0.685,0.979 1.100,1.153 0.415,0.174 10 ANT1 0.154,0.043 0.545,0.217 0.391,0.174 10 *a 2.271,1.064 1.841,1.064 false 1.584,1.064 1.153,1.064 false

Remove the electrical key antenna (outside luggage) (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ELECTRICAL KEY OSCILLATOR(for Outside Luggage Compartment)>REMOVAL)


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (ANT1) - 2 (ANT2) Always Below 1 Ω


Text in Illustration
*a Component without harness connected:
(Electrical Key Antenna (Outside Luggage))



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

8.INSPECT BACK DOOR OPENER SWITCH ASSEMBLY
a.

Remove the back door opener switch assembly (See page Vehicle Exterior>DOOR / HATCH>LUGGAGE COMPARTMENT DOOR OPENER OUTER SWITCH>REMOVAL).


b.

Inspect the back door opener switch assembly (See page Vehicle Exterior>DOOR / HATCH>LUGGAGE COMPARTMENT DOOR OPENER OUTER SWITCH>INSPECTION).



OK

9.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - BACK DOOR OPENER SWITCH ASSEMBLY)

NG

9.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - BACK DOOR OPENER SWITCH ASSEMBLY)
a.

Disconnect the D40 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the J2 back door opener switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D40-27 (TSW5) - J2-2 Always Below 1 Ω
J2-1 - Body ground Always Below 1 Ω
D40-27 (TSW5) - Body ground Always 10 kΩ or higher




OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.INSPECT LUGGAGE DOOR CLOSER ASSEMBLY
a.

Remove the luggage door closer assembly (See page Vehicle Interior>DOOR LOCK>LUGGAGE COMPARTMENT DOOR LOCK>REMOVAL).


b.

Inspect the luggage door closer assembly (See page Vehicle Interior>DOOR LOCK>LUGGAGE COMPARTMENT DOOR LOCK>INSPECTION).



OK

11.CHECK HARNESS AND CONNECTOR (LUGGAGE DOOR CLOSER - INSTRUMENT PANEL JUNCTION BLOCK)

NG

REPLACE LUGGAGE DOOR CLOSER ASSEMBLY

11.CHECK HARNESS AND CONNECTOR (LUGGAGE DOOR CLOSER - INSTRUMENT PANEL JUNCTION BLOCK)
a.

Disconnect the 3B and 3D instrument panel junction block assembly connectors.


b.

Disconnect the J3 luggage door closer assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3B-6 - J3-1 Always Below 1 Ω
3D-26 - J3-3 Always Below 1 Ω
J3-2 - Body ground Always Below 1 Ω
3B-6 - Body ground Always 10 kΩ or higher
3D-26 - Body ground Always 10 kΩ or higher




OK

12.REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Temporarily replace the instrument panel junction block assembly with a new one (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).



NEXT

13.CHECK OPERATION
13.CHECK OPERATION
a.

Check that the luggage compartment door entry unlock functions operate normally (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).


OK:

Luggage compartment door entry unlock functions operate normally.



OK

END (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (NETWORK GATEWAY ECU)