When the entry door lock and unlock functions and the wireless door lock and unlock functions do not operate, radio wave interference, or a malfunction in the key or signal circuit between the door control receiver and certification ECU (smart key ECU assembly) is suspected. The signal circuit is shared by the entry function and wireless door lock function.
When using the GTS with the engine switch off to troubleshoot:
Connect the GTS to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the GTS and vehicle begins.
The entry and start system (for Entry Function) uses a LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the entry and start system (for Entry Function) after confirming that the communication system is functioning properly.
Before replacing the certification ECU (smart key ECU assembly), refer to the entry and start system (for Entry Function) (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>PRECAUTION).
Check that there are no electrical key transmitter sub-assemblies in the vehicle.
Before performing the inspection, check that DTC B1242 (wireless door lock control) is not output (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>DTC CHECK / CLEAR).
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
When checking the entry lock operation multiple times, the lock operation may be limited to 2 consecutive operations depending on the settings. In order to perform the entry lock operation 3 or more times, an unlock operation must be performed once (any type of unlock operation is sufficient). However, only consecutive entry lock operations are limited. Using the wireless lock or other types of lock operations, it is possible to perform consecutive lock operations without this limitation.
After repair, confirm DTC does not reoccur by performing the "DTC Output Confirmation Operation".
Door control receiver has a constant voltage (12 V) supply circuit connected to terminal "+5".
Measure the voltage of the vehicle battery.
11 to 14 V
It may be possible to tell whether the vehicle battery is discharged by operating the horn.
If the voltage is below 11 V, recharge or replace the vehicle battery before proceeding.
NEXT
Open the driver door using the mechanical key built into the electrical key transmitter sub-assembly.
Connect the GTS and check for DTCs (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>DTC CHECK / CLEAR).
DTC is not output.
OK
NG
When the door control switch on the power window regulator master switch assembly on the driver door is operated, check that the doors unlock and lock according to the switch operation (See page Vehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK).
Door locks operate normally.
OK
NG
(See pageVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING)
Check if there are any other registered electrical key transmitter sub-assemblies.
| Result | Proceed to |
|---|---|
| There are no other registered electrical key transmitter sub-assemblies | A |
| There is another registered electrical key transmitter sub-assemblies | B |
A
B
Register a new electrical key transmitter sub-assembly (Refer to the Service Bulletin).
NEXT
Using another registered electrical key transmitter sub-assembly, check if an entry lock/unlock operation can be performed twice in succession.
Entry lock/unlock operate normally.
OK
NG
Check the transmitter battery level of the electrical key transmitter sub-assembly that was checked first.
Press and hold the lock switch of the transmitter for 5 seconds and check the number of times that the transmitter LED illuminates.
| Result | Proceed to |
|---|---|
| Transmitter LED does not illuminate when switch is pressed and held | A |
| Transmitter LED illuminates 3 times or more when switch is pressed and held | B |
| Transmitter LED illuminates once or twice but not a third time | C |
The electrical key transmitter sub-assembly sends voltage information to the certification ECU (smart key ECU assembly) when it is being used. The certification ECU (smart key ECU assembly) displays "Yes" for the "Key Low Battery" item of the Data List when this voltage information indicates 2.4 V or less (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>DATA LIST / ACTIVE TEST)
Even if the transmitter battery is depleted, it is still possible to start the engine by holding the electrical key transmitter sub-assembly against the engine switch, depressing the brake pedal and pressing the engine switch.
A
B
C
Remove the transmitter battery from the electrical key transmitter sub-assembly that does not operate (See page Vehicle Interior>DOOR LOCK>TRANSMITTER BATTERY(w/ Entry and Start System)>REPLACEMENT).
Attach a lead wire (0.60 mm (0.0236 in.) in diameter or less including wire sheath) with tape or equivalent to the negative terminal.
| *1 | Lead Wire |
Do not wrap the lead wire around a terminal, wedge it between terminals, or solder it. The terminal may be deformed or damaged, and the transmitter battery will not be able to be installed correctly.
Carefully pull the lead wire out from the position shown in the illustration and install the previously removed transmitter battery.
Measure the voltage of the transmitter battery.
| *a | GND |
When measuring the transmitter battery voltage, bring the electrical key transmitter sub-assembly within the lock entry operating range while operating the lock sensor of a door handle to perform the measurement.
Perform the measurement when the key is at room temperature.
The key sends voltage information to the certification ECU (smart key ECU assembly) when it is transmitting. When this voltage is 2.4 V or less the Data List item "Key Low Battery" displays "Yes". (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>DATA LIST / ACTIVE TEST)
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| Transmitter battery positive (+) - Transmitter battery negative (-) | Engine switch off, all doors closed and lock sensor touched | 2.5 to 3.2 V |
OK
NG
Bring the electrical key transmitter sub-assembly near the door control receiver and perform a wireless and entry function operation check.
When the electrical key transmitter sub-assembly is brought near the door control receiver, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.
If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.
There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.
If a tool for checking electric waves, such as a signal strength meter, is available, move around the area while observing both the LF band (used by the vehicle antenna to form the detection area) and RF band (used by the electrical key transmitter sub-assembly for transmission) to check for locations where there is wave interference.
Wireless and entry functions operate normally.
OK
NG
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Main Body / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| ACC SW | Engine switch on (ACC) / OFF or ON | OFF: Engine switch off
ON: Engine switch on (ACC) |
- |
| IG SW | Engine switch on (IG) / OFF or ON | OFF: Engine switch off
ON: Engine switch on (IG) |
- |
OK
NG
Disconnect the D48 certification ECU (smart key ECU assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D48-11 (GND) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D48-2 (+B) - Body ground | Always | 11 to 14 V |
| *a | Front view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly)) |
Reconnect the D48 certification ECU (smart key ECU assembly) connector.
OK
NG
Disconnect the D40 certification ECU (smart key ECU assembly) connector.
Disconnect the H26 door control receiver connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D40-5 (RCO) - H26-4 (+5) | Always | Below 1 Ω |
| D40-17 (RDA) - H26-5 (DATA) | Always | Below 1 Ω |
| D40-19 (RSSI) - H26-2 (RSSI) | Always | Below 1 Ω |
| D40-5 (RCO) - Body ground | Always | 10 kΩ or higher |
| D40-17 (RDA) - Body ground | Always | 10 kΩ or higher |
| D40-5 (RSSI) - Body ground | Always | 10 kΩ or higher |
OK
NG
Reconnect the H26 door control receiver connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H26-1 (GND) - Body ground | Always | Below 1 Ω |
| *a | Component with harness connected
(Door Control Receiver) |
OK
NG
Reconnect the D40 certification ECU (smart key ECU assembly) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H26-4 (+5) - H26-1 (GND) | Procedure:
1.
Engine switch off 2.
Electrical key transmitter sub-assembly switch not pressed |
Below 1 V |
| Procedure:
1.
Engine switch off 2.
Electrical key transmitter sub-assembly switch pressed |
4.5 to 5.5 V |
| *a | Component with harness connected
(Door Control Receiver) |
OK
NG
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H26-2 (RSSI) - H26-1 (GND) | Procedure:
1.
All doors closed 2.
All doors locked 3.
Electrical key transmitter sub-assembly switch not pressed |
11 to 14 V |
| Procedure:
1.
All doors closed 2.
All doors locked 3.
Electrical key transmitter sub-assembly switch pressed |
Below 2 V | |
| H26-5 (DATA) - H26-1 (GND) | Procedure:
1.
All doors closed 2.
All doors locked 3.
Electrical key transmitter sub-assembly switch not pressed |
11 to 14 V |
1.
All doors closed 2.
All doors locked 3.
Electrical key transmitter sub-assembly switch pressed |
11 to 14 V → Below 2 V → 11 to 14 V pulse generation output at regular interval |
| *a | Component with harness connected
(Door Control Receiver) |
OK
NG
Temporarily replace the certification ECU (smart key ECU assembly) with a new one.
When the certification ECU (smart key ECU assembly) is replaced, it is also necessary to replace all registered electrical key transmitter sub-assemblies.
NEXT
Check that the wireless door lock functions operate normally (See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Entry and Start System)>OPERATION CHECK).
Wireless door lock functions operate normally.
OK
NG