Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function)
RM2090E _58 Vehicle Interior _060697 THEFT DETERRENT / KEYLESS ENTRY _0297681 ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  B2282  Vehicle Speed Signal Malfunction  B2283  Vehicle Speed Sensor Malfunction  


DESCRIPTION

DTC B2282 is stored when a mismatch between the vehicle speed signal from the direct line sent by the brake actuator assembly (skid control ECU) and the vehicle speed signal sent via CAN communication is detected.

DTC B2283 is stored when a malfunction in the vehicle speed sensor is detected.

HINT:

When the battery cable is disconnected and reconnected, the power source returns to the mode it was in before the battery cable was disconnected.


DTC No. DTC Detection Condition Trouble Area DTC Output Confirmation Operation
B2282 Mismatch between the vehicle speed signal from the direct line sent by the brake actuator assembly (skid control ECU) and the vehicle speed signal sent via CAN communication (1-trip detection logic*1).
·

AM2 NO. 2 fuse

·

Vehicle stability control system

·

Certification ECU (smart key ECU assembly)

·

Headlight leveling ECU assembly

·

Radio receiver assembly

·

Wire harness or connector


Drive the vehicle for 20 seconds at a vehicle speed of 25 km/h (16 mph) or more, and then drive the vehicle at a vehicle speed that is less than 5 km/h (3 mph) for 20 seconds.
B2283 Either condition is met (vehicle speed sensor malfunction is detected) (1-trip detection logic*1):
·

Vehicle speed signal malfunction detection 1: Large decrease in speed is detected.

·

Vehicle speed signal malfunction detection 2: Malfunction detected using engine speed-linked detection.


·

AM2 NO. 2 fuse

·

Vehicle stability control system

·

Certification ECU (smart key ECU assembly)

·

Headlight leveling ECU assembly

·

Radio receiver assembly

·

Wire harness or connector


Run the engine at an engine speed of 2000 rpm or more for 330 seconds.

*1: Only output while a malfunction is present and the engine switch is on (IG)


Vehicle Condition and Fail-safe Function when Malfunction Detected
DTC No. Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
B2282
·

When the signal from the direct line or CAN communication is malfunctioning and indicates no vehicle speed, there is no effect on vehicle behavior.

·

When the signal from the direct line or CAN communication is malfunctioning and indicates that the vehicle is moving, the power source mode cannot be turned from on (IG) to off.


-
B2283
·

If the engine switch is pressed while the vehicle is being driven, the engine switch turns off (the engine stops).

·

When the electrical key transmitter sub-assembly is inside the vehicle, the engine does not start even though an engine start operation is performed.


Steering lock motor operation is prohibited.

Related Data List and Active Test Items
DTC No. Data List Item Active Test Item
B2282
B2283
Power Source Control
·

Vehicle Speed Signal

·

Engine Condition

·

Power Supply Condition


Engine
·

Engine Speed


ABS/VSC/TRC
·

Vehicle Speed


-

WIRING DIAGRAM

B526469E03
2.448,0.375 3.688,0.813 1.24,0.438 10 false from MAIN Fuse 3.969,0.552 5.208,0.99 1.24,0.438 10 false AM2 NO. 2 1.708,1.219 2.948,1.656 1.24,0.438 10 false SPD 2.094,1.115 3.333,1.552 1.24,0.438 10 false 2 0.76,1.604 2,2.042 1.24,0.438 10 false A5 0.76,1.781 2.365,2.406 1.604,0.625 10 false Brake Actuator Assembly (Skid Control ECU) 5,0.385 5.469,0.615 0.469,0.229 10 false D48 5.365,0.406 5.833,0.635 0.469,0.229 10 false +B 5.094,0.177 6.333,0.615 1.24,0.438 10 false 2 5.031,1.01 6.271,1.448 1.24,0.438 10 false 27 5,1.219 5.469,1.448 0.469,0.229 10 false D41 5,1.677 5.469,1.906 0.469,0.229 10 false D48 5.031,1.479 6.271,1.917 1.24,0.438 10 false 11 5.365,1.208 5.833,1.438 0.469,0.229 10 false SPD 5.354,1.688 5.823,1.917 0.469,0.229 10 false GND 5.115,2.104 6.656,2.781 1.542,0.677 10 false Certification ECU (Smart Key ECU Assembly) 5.104,2.833 6.344,3.271 1.24,0.438 10 false 17 5.375,2.969 5.844,3.198 0.469,0.229 10 false SPD 4.938,3.229 5.406,3.458 0.469,0.229 10 false D12 4.927,3.385 6.969,4.031 2.042,0.646 10 false Radio Receiver Assembly 2.115,2.833 3.354,3.271 1.24,0.438 10 false 16 1.594,2.979 2.229,3.281 0.635,0.302 10 false SPDR 0.771,3.354 2.01,3.792 1.24,0.438 10 false A16 0.771,3.5 2.229,4.177 1.458,0.677 10 false Headlight Leveling ECU Assembly 5.063,4.406 7,4.667 1.938,0.26 10 false : CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off to troubleshoot:

Connect the GTS to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the GTS and vehicle begins.

·

The entry and start system uses multiplex communication. First perform the inspections in "How to Proceed with Troubleshooting" to confirm that there are no communication malfunctions before proceeding with troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

Before replacing the certification ECU (smart key ECU assembly), refer to the entry and start system (for Entry Function) (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>PRECAUTION).

·

After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.

·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.READ VALUE USING GTS (VEHICLE SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


e.

According to the display on the GTS, read the Data List.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Vehicle Speed Vehicle speed/Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph) Almost same as actual vehicle speed (Speedometer tester) -

OK:

The Data List value is approximately the same as the actual vehicle speed.




OK

2.READ VALUE USING GTS (VEHICLE SPEED SIGNAL)

NG

GO TO VEHICLE STABILITY CONTROL SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

2.READ VALUE USING GTS (VEHICLE SPEED SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Power Source Control / Data List.


e.

According to the display on the GTS, read the Data List.

Power Source Control
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Vehicle Speed Signal Vehicle moving or stationary / Stop or Run Run: Vehicle moving at 5 km/h (3 mph) or more
Stop: Vehicle stopped
-

OK:

Stop (vehicle stopped) or Run (vehicle moving) appears on the screen according to the vehicle speed.




OK

GO TO VEHICLE STABILITY CONTROL SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

NG

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE)
3.CHECK HARNESS AND CONNECTOR (POWER SOURCE)

OK

4.CHECK HARNESS AND CONNECTOR (GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR IN CIRCUIT CONNECTED TO POWER SOURCE

4.CHECK HARNESS AND CONNECTOR (GROUND)

OK

5.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU))
a.

Disconnect the D41 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the A5 brake actuator assembly (skid control ECU) connector.


c.

Disconnect the A16 headlight leveling ECU assembly connector.


d.

Disconnect the D12 radio receiver assembly connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D41-27 (SPD) - A5-2 (SPD) Always Below 1 Ω
D41-27 (SPD) - Body ground and other terminals Always 10 kΩ or higher




OK

6.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
U190214E02
2.708,1.208 2.542,1.677 true 4.688,1.219 4.833,1.729 true 0.104,0.042 0.292,0.229 0.188,0.188 10 false *a 4.479,2.823 4.813,3 0.333,0.177 10 false GND 2.354,1.698 2.698,1.854 0.344,0.156 10 false GND 4.729,1.792 5.094,1.948 0.365,0.156 10 false SPD 4.771,0.365 5.063,0.521 0.292,0.156 10 false D41 2.177,0.365 2.469,0.521 0.292,0.156 10 false D48

Text in Illustration
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
- -

a.

Reconnect the A5 brake actuator assembly (skid control ECU) connector.


b.

Reconnect the D41 certification ECU (smart key ECU assembly) connector.


c.

Reconnect the A16 headlight leveling ECU assembly connector.


d.

Reconnect the D12 radio receiver assembly connector.


e.

Using an oscilloscope, check the vehicle speed input signal waveform from the brake actuator assembly (skid control ECU) at the terminal of the certification ECU (smart key ECU assembly).

i.

Check the signal waveform according to the conditions in the table below.

Item Content
Tester Connection D41-27 (SPD) - D48-11 (GND)
Tool Setting 5 V/DIV., 10 ms./DIV.
Condition Engine switch on (IG), vehicle being driven at approx. 5 km/h (3 mph)

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. The wavelength becomes shorter as the vehicle speed increases.





OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

7.INSPECT HEADLIGHT LEVELING ECU ASSEMBLY (SHORT CIRCUIT IN HEADLIGHT LEVELING ECU ASSEMBLY)
7.INSPECT HEADLIGHT LEVELING ECU ASSEMBLY (SHORT CIRCUIT IN HEADLIGHT LEVELING ECU ASSEMBLY)
U190214E02
2.708,1.208 2.542,1.677 true 4.688,1.219 4.833,1.729 true 0.104,0.042 0.292,0.229 0.188,0.188 10 false *a 4.479,2.823 4.813,3 0.333,0.177 10 false GND 2.354,1.698 2.698,1.854 0.344,0.156 10 false GND 4.729,1.792 5.094,1.948 0.365,0.156 10 false SPD 4.771,0.365 5.063,0.521 0.292,0.156 10 false D41 2.177,0.365 2.469,0.521 0.292,0.156 10 false D48

Text in Illustration
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
- -

a.

Disconnect the A16 headlight leveling ECU assembly connector.


b.

Using an oscilloscope, check the vehicle speed input signal waveform from the brake actuator assembly (skid control ECU) at the terminal of the certification ECU (smart key ECU assembly).

i.

Check the signal waveform according to the conditions in the table below.

Item Content
Tester Connection D41-27 (SPD) - D48-11 (GND)
Tool Setting 5 V/DIV., 10 ms./DIV.
Condition Engine switch on (IG), vehicle being driven at approx. 5 km/h (3 mph)

OK:

The waveform is similar to that shown in the illustration.


HINT:

If the result is as specified, there may be a short circuit in the headlight leveling ECU assembly.





OK

REPLACE HEADLIGHT LEVELING ECU ASSEMBLY

NG

8.INSPECT RADIO RECEIVER ASSEMBLY (SHORT CIRCUIT IN RADIO RECEIVER ASSEMBLY)
8.INSPECT RADIO RECEIVER ASSEMBLY (SHORT CIRCUIT IN RADIO RECEIVER ASSEMBLY)
U190214E02
2.708,1.208 2.542,1.677 true 4.688,1.219 4.833,1.729 true 0.104,0.042 0.292,0.229 0.188,0.188 10 false *a 4.479,2.823 4.813,3 0.333,0.177 10 false GND 2.354,1.698 2.698,1.854 0.344,0.156 10 false GND 4.729,1.792 5.094,1.948 0.365,0.156 10 false SPD 4.771,0.365 5.063,0.521 0.292,0.156 10 false D41 2.177,0.365 2.469,0.521 0.292,0.156 10 false D48

Text in Illustration
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
- -

a.

Disconnect the D12 radio receiver assembly connector.


b.

Using an oscilloscope, check the vehicle speed input signal waveform from the brake actuator assembly (skid control ECU) at the terminal of the certification ECU (smart key ECU assembly).

i.

Check the signal waveform according to the conditions in the table below.

Item Content
Tester Connection D41-27 (SPD) - D48-11 (GND)
Tool Setting 5 V/DIV., 10 ms./DIV.
Condition Engine switch on (IG), vehicle being driven at approx. 5 km/h (3 mph)

OK:

The waveform is similar to that shown in the illustration.


HINT:

If the result is as specified, there may be a short circuit in the radio receiver assembly.





OK

REPLACE RADIO RECEIVER ASSEMBLY

NG

9.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (SHORT CIRCUIT IN CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
9.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (SHORT CIRCUIT IN CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Disconnect the A5 brake actuator assembly (skid control ECU) connector.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
D12-17 (SPD) - Body ground Engine switch off 10 kΩ or higher


HINT:

If the result is as specified, there may be a short circuit in the brake actuator assembly (skid control ECU).




OK

REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)