Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System)
RM2090E _58 Vehicle Interior _060697 THEFT DETERRENT / KEYLESS ENTRY _0297684 ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System) J

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System)  Security Indicator Light Does not Blink  


DESCRIPTION

When the engine immobiliser system is set, the security indicator light blinks continuously, but does not illuminate if the engine immobiliser system is not set.


WIRING DIAGRAM

B311631E02
0.51,3.073 2.094,3.417 1.583,0.344 10 false Main Body ECU (Network Gateway ECU) 1.833,1.708 4.51,1.896 2.677,0.188 10 false Instrument Panel Junction Block Assembly 4.802,1.74 6.635,1.938 1.833,0.198 10 false Combination Meter Assembly 4.813,1.563 5.031,1.719 0.219,0.156 10 false D7 1.833,1.531 2.063,1.677 0.229,0.146 10 false 3B 4.094,1.042 4.302,1.188 0.208,0.146 10 false 22 1.896,0.927 2.073,1.094 0.177,0.167 10 false 27 6.094,1.031 6.292,1.188 0.198,0.156 10 false 40 5.01,1.031 5.198,1.188 0.188,0.156 10 false 18 5.75,1.146 6.063,1.292 0.313,0.146 10 false ES2 5.26,1.146 5.573,1.292 0.313,0.146 10 false ILL+ 1.865,1.146 2.104,1.292 0.24,0.146 10 false MB 1.875,0.51 2.115,0.656 0.24,0.146 10 false MB 1.927,0.302 2.052,0.448 0.125,0.146 10 false 8 1.573,0.51 1.76,0.656 0.188,0.146 10 false IG 2.375,0.667 2.99,0.813 0.615,0.146 10 false ECU IG1 1.521,1.167 1.76,1.313 0.24,0.146 10 false ILL 1.406,2.677 1.771,2.823 0.365,0.146 10 false KSW 1.896,2.458 2.094,2.625 0.198,0.167 10 false 22 1.885,2.656 2.125,2.802 0.24,0.146 10 false D5 3.292,0.51 4.031,0.885 0.74,0.375 10 false to IG1 No. 1 Relay 3.125,2.563 3.396,2.708 0.271,0.146 10 false UN- 3.781,2.573 4.104,2.719 0.323,0.146 10 false UN+ 4.156,2.552 4.292,2.698 0.135,0.146 10 false 1 2.927,2.563 3.063,2.708 0.135,0.146 10 false 2 2.854,3.156 4.344,3.531 1.49,0.375 10 false Un-lock Warning Switch Assembly 2.865,2.969 3.135,3.125 0.271,0.156 10 false D53 4.667,2.802 4.958,2.969 0.292,0.167 10 false HAZ 5.542,2.667 6.448,2.865 0.906,0.198 10 false to MAIN Fuse

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

If the combination meter assembly and main body ECU (network gateway ECU) is replaced, refer to Service Bulletin.



PROCEDURE

2.PERFORM ACTIVE TEST USING GTS (SECURITY INDICATOR)
a.

Check that the security indicator light illuminates when operating it with the Active Test (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System)>DATA LIST / ACTIVE TEST).

Main Body
Tester Display Test Part Control Range Diagnostic Note
Security Indicator Security indicator light ON/OFF -

OK:

Security indicator light can be turned on and off using the GTS.




OK

3.READ VALUE USING GTS (IG SW, KEY UNLOCK WARNING SW)

NG

6.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK - COMBINATION METER ASSEMBLY)
3.READ VALUE USING GTS (IG SW, KEY UNLOCK WARNING SW)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
IG SW Ignition switch ON signal / OFF or ON OFF: Ignition switch ACC or off
ON: Ignition switch ON
-
Key Unlock Warning SW Un-lock warning switch signal / OFF or ON OFF: No key in ignition key cylinder
ON: Key inserted in ignition key cylinder
-


OK:

On the GTS screen, the display changes between ON and OFF according to the chart above.


Result
Result Proceed to
OK A
NG (IG SW) B
NG (Key Unlock Warning SW) C


A

REPLACE MAIN BODY ECU (NETWORK GATEWAY ECU)

B

GO TO LIGHTING SYSTEM (IG Signal Circuit)

C

4.INSPECT UN-LOCK WARNING SWITCH ASSEMBLY
4.INSPECT UN-LOCK WARNING SWITCH ASSEMBLY
a.

Remove the un-lock warning switch assembly (See page Vehicle Interior>DOOR LOCK>UNLOCK WARNING SWITCH>REMOVAL).


b.

Inspect the un-lock warning switch assembly (See page Vehicle Interior>DOOR LOCK>UNLOCK WARNING SWITCH>INSPECTION).



OK

5.CHECK HARNESS AND CONNECTOR (UN-LOCK WARNING SWITCH ASSEMBLY - MAIN BODY ECU)

NG

REPLACE UN-LOCK WARNING SWITCH ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (UN-LOCK WARNING SWITCH ASSEMBLY - MAIN BODY ECU)
U146904E01
0.191,0.118 0.377,0.279 0.186,0.161 10 *a 1.574,0.28 1.870,0.436 0.295,0.156 10 D53 1.072,1.425 1.51,1.425 false 1.949,1.425 2.386,1.425 false 2.438,1.337 2.785,1.493 0.347,0.156 10 UN- 0.686,1.337 1.033,1.493 0.347,0.156 10 UN+

a.

Disconnect the D5 main body ECU (network gateway ECU) connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D53-1 (UN+) - Body ground Always 11 to 14 V


Standard Resistance:
Tester Connection Condition Specified Condition
D53-2 (UN-) - D5-22 (KSW) Always Below 1 Ω
D53-2 (UN-) - Body ground Always 10 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Un-lock Warning Switch Assembly)



OK

REPLACE MAIN BODY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK - COMBINATION METER ASSEMBLY)
a.

Disconnect the 3B instrument panel junction block assembly connector.


b.

Disconnect the D7 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3B-22 - D7-18 Always Below 1 Ω
D7-40 - Body ground Always Below 1 Ω
3B-22 - Body ground Always 10 kΩ or higher




OK

7.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


b.

Remove the main body ECU (network gateway ECU) from the instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.


U190237E01
0.114,0.061 0.300,0.222 0.186,0.161 10 *a 2.219,0.427 2.462,0.583 0.243,0.156 10 MB 5.651,0.22 5.869,0.376 0.218,0.156 10 3B 3.469,0.94 3.528,1.175 false 3.447,1.19 3.689,1.346 0.243,0.156 10 ILL

Text in Illustration
*a Component without harness connected
(Instrument Panel Junction Block Assembly )
- -

Standard Resistance:
Tester Connection Condition Specified Condition
MB-27 (ILL) - 3B-22 Always Below 1 Ω



OK

8.REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

8.REPLACE COMBINATION METER ASSEMBLY
a.

Replace the combination meter assembly with a new one (See page Vehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL).


b.

When the immobiliser is set, check that the security indicator light blinks.


OK:

Security indicator light blinks.



OK

END (COMBINATION METER ASSEMBLY WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (NETWORK GATEWAY ECU)