Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › from 2016.06
RM2090E _58 Vehicle Interior _060699 METER / GAUGE / DISPLAY _0297701 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Malfunction in Water Temperature Warning Light  


DESCRIPTION

In this circuit, the combination meter assembly receives engine coolant temperature signals from the ECM via CAN communication. The combination meter assembly displays an engine coolant temperature warning based on the data received from the ECM.

WIRING DIAGRAM

E357051E04
2.74,1.729 4.344,1.938 1.604,0.208 10 false CAN Communication Line 1.927,2.823 2.281,3.021 0.354,0.198 10 false ECM 4.781,2.771 4.99,2.948 0.208,0.177 10 false D7 1.354,2.823 1.708,3.021 0.354,0.198 10 false A33 4.781,2.938 6.26,3.292 1.479,0.354 10 false Combination Meter Assembly

PROCEDURE

1.CHECK FOR DTC (METER / GAUGE SYSTEM)
a.

Check if meter / gauge system DTCs are output (Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR).

OK:

DTCs are not output.




OK

2.CHECK FOR DTC (SFI SYSTEM)

NG

2.CHECK FOR DTC (SFI SYSTEM)
a.

Check if SFI system DTCs are output (Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).

OK:

DTCs are not output.




OK

3.CHECK TELLTALE LIGHT (WATER TEMPERATURE WARNING (COLD))

NG

3.CHECK TELLTALE LIGHT (WATER TEMPERATURE WARNING (COLD))
a.
A280086E10
0.771,1.469 1.021,1.656 0.25,0.188 10 false *1 2.583,1.479 2.854,1.677 0.271,0.198 10 false *2 2.229,0.583 2.542,0.813 0.313,0.229 10 false THW 2.24,0.958 2.448,1.146 0.208,0.188 10 false E1

Disconnect the engine coolant temperature sensor connector.


b.

Turn the ignition switch to ON.


c.

Check the operating condition of the water temperature warning light.


Text In Illustration
*1 Engine Coolant Temperature Sensor
*2 ECM

Result:
Result Proceed to
Water temperature warning light (blue) is on. A
Water temperature warning light (blue) is not on. B



A

4.CHECK TELLTALE LIGHT (WATER TEMPERATURE WARNING (HOT))

B

REPLACE COMBINATION METER ASSEMBLY

4.CHECK TELLTALE LIGHT (WATER TEMPERATURE WARNING (HOT))
a.

Disconnect the engine coolant temperature sensor connector.


b.
U190097E02
1.563,2.677 1.135,2.927 true 1.875,2.688 2.292,2.938 true 0.74,1.375 1.01,1.604 0.271,0.229 10 false *1 0.271,1.896 0.542,2.125 0.271,0.229 10 false *a 0.896,2.885 1.24,3.115 0.344,0.229 10 false E2 2.24,0.844 2.583,1.073 0.344,0.229 10 false E1 2.354,2.844 2.813,3.073 0.458,0.229 10 false THW 2.229,0.479 2.688,0.708 0.458,0.229 10 false THW 2.594,1.365 2.865,1.594 0.271,0.229 10 false *2 0.823,2.479 1.177,2.75 0.354,0.271 10 false C40

Connect terminals 1 and 2 of the engine coolant temperature sensor connector on the wire harness side.


c.

Turn the ignition switch to ON.


d.

Check the operating condition of the water temperature warning light.


Result:
Result Proceed to
Water temperature warning light (red) is on. A
Water temperature warning light (red) is not on. B


Text In Illustration
*1 Engine Coolant Temperature Sensor
*2 ECM
*3 Front view of wire harness connector
(to Engine Coolant Temperature Sensor)


A

5.INSPECT ENGINE COOLANT TEMPERATURE SENSOR

B

REPLACE COMBINATION METER ASSEMBLY

5.INSPECT ENGINE COOLANT TEMPERATURE SENSOR

OK

NG