Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2012.03–2016.06
RM2090E _58 Vehicle Interior _060699 METER / GAUGE / DISPLAY _0297701 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Tachometer Malfunction  


DESCRIPTION

The combination meter assembly controls the tachometer in accordance with the engine speed signals from the ECM through the CAN communication system.

WIRING DIAGRAM

E357051E03
2.74,1.729 4.344,1.938 1.604,0.208 10 false CAN Communication Line 1.271,2.906 1.625,3.104 0.354,0.198 10 false ECM 4.781,2.771 4.99,2.948 0.208,0.177 10 false D7 1.281,2.75 1.635,2.948 0.354,0.198 10 false A33 4.781,2.938 6.26,3.292 1.479,0.354 10 false COMBINATION METER ASSEMBLY

PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication DTCs are output (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTCs are not output A
DTCs are output B



A

2.PERFORM ACTIVE TEST USING GTS (TACHOMETER OPERATION)

B

2.PERFORM ACTIVE TEST USING GTS (TACHOMETER OPERATION)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Active Test.


e.

According to the display on the tester, perform the Active Test.

Combination Meter
Tester Display Test Part Control Range Diagnostic Note
Tachometer Operation Tachometer 0, 1000, 2000, 3000, , 4000, 5000, 6000, 7000 rpm -

OK:

The engine speed displayed on the tester is approximately the same as that of the tachometer reading.




OK

3.READ VALUE USING GTS (ENGINE RPM)

NG

REPLACE COMBINATION METER ASSEMBLY

3.READ VALUE USING GTS (ENGINE RPM)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Data List.


e.

According to the display on the tester, read the Data List.

Combination Meter
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Engine Rpm Engine speed
Min.: 0
Max.: 12750
Approximately same as actual engine speed (when engine is running) Unit: rpm

OK:

The engine speed displayed on the tester is approximately the same as that displayed on the combination meter assembly.


NOTICE:

Determine whether the value displayed on the tester is within the acceptable range by referring to the reference values described in "On-Vehicle Inspection" (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>ON-VEHICLE INSPECTION).




OK

4.CHECK SFI SYSTEM

NG

REPLACE COMBINATION METER ASSEMBLY

4.CHECK SFI SYSTEM
a.

Check if the SFI system outputs DTCs (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTCs are not output A
DTCs are output B



A

5.READ VALUE USING GTS (ENGINE SPEED)

B

5.READ VALUE USING GTS (ENGINE SPEED)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List.


e.

According to the display on the tester, read the Data List.

Combination Meter
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Engine Speed Engine speed
Min.: 0
Max.: 16383.75
Approximately same as actual engine speed (when engine is running) Unit: rpm

OK:

The engine speed displayed on the tester is approximately the same as that displayed on the combination meter assembly.


NOTICE:

Determine whether the value displayed on the tester is within the acceptable range by referring to the reference values described in "On-Vehicle Inspection" (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>ON-VEHICLE INSPECTION).




OK

6.REPLACE COMBINATION METER ASSEMBLY

NG

6.REPLACE COMBINATION METER ASSEMBLY
a.

Replace the combination meter assembly with a new or a normal one (See page Vehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL).


OK:

The operation of the tachometer returns to normal.



OK

END

NG