Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Manual Air Conditioning System)
RM2090E _58 Vehicle Interior _060704 HEATING / AIR CONDITIONING _0297735 AIR CONDITIONING SYSTEM(for Manual Air Conditioning System) J

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Manual Air Conditioning System)  Air Conditioning Compressor Magnetic Clutch Circuit  


DESCRIPTION

When the No.3 heater control sub-assembly is turned on, a magnetic clutch on signal is sent from the AC terminal of the ECM. Then, the engine room relay block assembly turns on to operate the magnetic clutch assembly.

WIRING DIAGRAM

E249944E02
0.438,2.99 2.406,3.188 1.969,0.198 10 false Compressor with Magnet Clutch 3.552,4.083 3.854,4.25 0.302,0.167 10 false ECM 5.208,2.906 6.802,3.26 1.594,0.354 10 false Main Body ECU (Network Gateway ECU) 1,2.469 2.01,2.646 1.01,0.177 10 false Magnetic Clutch 0.781,1.729 1.542,1.917 0.76,0.188 10 false Heater relay 0.583,4.406 2.281,4.594 1.698,0.188 10 false : CAN Communication Line 0.792,0.615 2.073,0.813 1.281,0.198 10 false from IG1 NO.3 Relay 0.354,0.271 2.313,0.469 1.958,0.198 10 false from Heater Blower Motor Relay 1.365,1.24 1.469,1.385 0.104,0.146 10 false 3 0.833,1.25 0.938,1.396 0.104,0.146 10 false 5 0.833,1.594 0.938,1.74 0.104,0.146 10 false 1 1.375,1.583 1.479,1.729 0.104,0.146 10 false 2 2.375,2.094 2.479,2.24 0.104,0.146 10 false 1 5.229,2.615 5.438,2.792 0.208,0.177 10 false D5 2.938,3.823 3.198,3.979 0.26,0.156 10 false A35 2.99,3.635 3.156,3.792 0.167,0.156 10 false 35 2.927,3.427 3.188,3.583 0.26,0.156 10 false A33 3.01,3.24 3.115,3.385 0.104,0.146 10 false 8 5.219,1.844 5.427,2.01 0.208,0.167 10 false D6 5.229,1.656 5.406,1.802 0.177,0.146 10 false 17 4.281,3.823 4.542,3.979 0.26,0.156 10 false A33 5.406,0.5 5.51,0.646 0.104,0.146 10 false 3 6.375,0.5 6.479,0.646 0.104,0.146 10 false 4 5.594,0.625 5.844,0.771 0.25,0.146 10 false A/C 5.406,0.188 5.51,0.333 0.104,0.146 10 false 2 5.583,0.292 5.698,0.438 0.115,0.146 10 false B 5.979,0.625 6.313,0.771 0.333,0.146 10 false LED- 2.458,0.417 3.188,0.563 0.729,0.146 10 false HEATER-S 2.198,0.75 2.792,0.896 0.594,0.146 10 false HEATER 3.927,1.417 4.031,1.563 0.104,0.146 10 false 4 3.927,1.688 4.031,1.833 0.104,0.146 10 false 2 3.073,1.698 3.177,1.844 0.104,0.146 10 false 3 3.073,1.396 3.177,1.542 0.104,0.146 10 false 1 0.438,2.833 0.719,3 0.281,0.167 10 false C17 4.927,0.938 7.063,1.115 2.135,0.177 10 false No.3 Heater Control Sub-assembly 4.927,0.76 5.198,0.927 0.271,0.167 10 false D21 2.875,2.208 4.396,2.729 1.521,0.521 10 false Air conditioner Tube and Accessory Assembly (Pressure Switch) 2.875,2.042 3.083,2.198 0.208,0.156 10 false A7 1.969,2.094 2.292,2.25 0.323,0.156 10 false MG+ 3.25,3.417 3.563,3.583 0.313,0.167 10 false ACP 3.25,3.813 3.479,3.958 0.229,0.146 10 false AC 3.833,3.448 4.229,3.594 0.396,0.146 10 false CANL 3.802,3.823 4.229,3.969 0.427,0.146 10 false CANH 4.323,3.26 4.51,3.406 0.188,0.146 10 false 18 4.323,3.635 4.51,3.792 0.188,0.156 10 false 19 5.219,2.219 5.427,2.385 0.208,0.167 10 false D5 3.24,1.813 3.552,1.958 0.313,0.146 10 false ACP 3.24,1.5 3.469,1.646 0.229,0.146 10 false AC 3.75,1.51 3.865,1.656 0.115,0.146 10 false B 3.74,1.823 3.854,1.969 0.115,0.146 10 false E 5.229,2.031 5.417,2.198 0.188,0.167 10 false 13 5.229,2.427 5.417,2.573 0.188,0.146 10 false 14 6.01,4.271 6.385,4.438 0.375,0.167 10 false DLC3 5.354,3.667 5.531,3.813 0.177,0.146 10 false 14 5.406,3.917 5.5,4.063 0.094,0.146 10 false 6 5.635,4.271 5.917,4.438 0.281,0.167 10 false D10 4.281,3.438 4.552,3.604 0.271,0.167 10 false A33 5.583,3.792 5.979,3.938 0.396,0.146 10 false CANL 5.583,4.031 6.01,4.177 0.427,0.146 10 false CANH 5.5,2.208 5.896,2.354 0.396,0.146 10 false CANL 5.5,2.604 5.927,2.771 0.427,0.167 10 false CANH

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Date List.


e.

Check the value(s) by referring to the table below.

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
A/C SW Input A/C Switch Input
OFF or ON
ON: A/C switch on
OFF: A/C switch off
-

OK:

The display is as specified in the normal condition column.

Result
Result Proceed to
NG A
OK B




A

2.CHECK HARNESS AND CONNECTOR (NO. 3 HEATER CONTROL SUB-ASSEMBLY - POWER SOURCE)

B

5.READ VALUE USING GTS
2.CHECK HARNESS AND CONNECTOR (NO. 3 HEATER CONTROL SUB-ASSEMBLY - POWER SOURCE)
a.

Disconnect the D21 No. 3 heater control sub-assembly connector.


b.

Measure the voltage according to the valve(s) in the table below.


Standard Voltage:
Tester Connection Condition Specified Condition
D21-2(B) - Body ground
·

Ignition switch on

·

Blower switch: on


11 to 14 V



OK

3.INSPECT NO. 3 HEATER CONTROL SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT NO. 3 HEATER CONTROL SUB-ASSEMBLY

OK

4.CHECK HARNESS AND CONNECTOR (NO. 3 HEATER CONTROL SUB-ASSEMBLY - MAIN BODY ECU (NETWORK GATEWAY ECU))

NG

4.CHECK HARNESS AND CONNECTOR (NO. 3 HEATER CONTROL SUB-ASSEMBLY - MAIN BODY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the D6 main body ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D6-17 - D21-3(A/C) Always Below 1 Ω
D6-17 - Body ground Always 10 kΩ or higher




OK

REPLACE NETWORK GATEWAY ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.READ VALUE USING GTS
a.

Enter the following menus: Powertrain / Engine and ETC / Date List.


b.

Check the value(s) by referring to the table below.

Engine
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
A/C Pressure Normal SW Pressure Switch status
ON or OFF
ON -

OK:

The display is as specified in the normal condition column.

Result
Result Proceed to
NG A
OK B


OK:

The display is as specified in the normal condition column.




A

6.CHECK REFRIGERANT VOLUME

B

12.READ VALUE USING GTS
6.CHECK REFRIGERANT VOLUME
a.

b.

Check the refrigerant volume (for HFO-1234yf(R1234yf)) (See page Vehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT(for HFO-1234yf(R1234yf))>ON-VEHICLE INSPECTION).



OK

7.CHECK HARNESS AND CONNECTOR (AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY - POWER SOURCE)

NG

CHARGE REFRIGERANT

7.CHECK HARNESS AND CONNECTOR (AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY - POWER SOURCE)
a.

Disconnect the A7 air conditioner tube and accessory assembly connector.


b.

Measure the voltage according to the value(s) in the table below.


U190428E02
1.771,1.417 2.542,1.729 true 0.125,0.083 0.292,0.25 0.167,0.167 10 false *a 2.604,1.656 2.76,1.865 0.156,0.208 10 false B 1.615,0.313 1.813,0.469 0.198,0.156 10 false A7

Standard Voltage:
Tester Connection Condition Specified Condition
A7-4(B) - Body ground Ignition switch on 11 to 14 V



OK

8.CHECK HARNESS AND CONNECTOR (AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
A7-2(E) - Body ground Always Below 1 Ω



OK

9.CHECK HARNESS AND CONNECTOR (AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY - HEATER RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY - HEATER RELAY)
a.

Remove the heater relay from the engine room relay block assembly.


b.

Measure the resistance according to the value(s) in the table below.


E234483E01
0.171,0.402 0.333,0.588 0.163,0.186 10 *1

Standard Resistance:
Tester Connection Condition Specified Condition
A7-1(AC) - 2 Always Below 1 Ω
A7-1(AC) - Body ground Always 10 kΩ or higher


Text in Illustration
*1 Component without relay installed
(Engine Room Relay Block Assembly)


OK

10.CHECK HARNESS AND CONNECTOR (AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY - ECM)
a.

Disconnect the A33 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
A7-3(ACP) - A33-8(ACP) Always Below 1 Ω
A7-3(ACP) - Body ground Always 10 kΩ or higher



OK

11.INSPECT AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.INSPECT AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY
a.

Inspect the air conditioner tube and accessory assembly (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING PRESSURE SENSOR>ON-VEHICLE INSPECTION)



OK

REPLACE ECM

NG

REPLACE AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY

12.READ VALUE USING GTS
a.

Enter the following menus: Powertrain / Engine and ETC / Date List.


b.

Check the value(s) by referring to the table below.

Engine
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
A/C Signal A/C Signal /
OFF or ON
A/C switch operated: ON (when switch is pressed) -
A/C switch not operated: OFF (when switch is not pressed)

OK:

The display is as specified in the normal condition column.

Result
Result Proceed to
NG A
OK B


OK:

The display is as specified in the normal condition column.




A

13.INSPECT HEATER RELAY

B

15.CHECK HARNESS AND CONNECTOR (HEATER RELAY - COMPRESSOR WITH MAGNET CLUTCH)
13.INSPECT HEATER RELAY
a.

Remove the heater relay from the engine room relay block assembly.




OK

14.CHECK HARNESS AND CONNECTOR (HEATER RELAY - POWER SOURCE)

NG

REPLACE HEATER RELAY

14.CHECK HARNESS AND CONNECTOR (HEATER RELAY - POWER SOURCE)
a.
E234483E01
0.171,0.402 0.333,0.588 0.163,0.186 10 *1

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
5 - Body ground Ignition switch off Below 1 V
Ignition switch on 11 to 14V


Text in Illustration
*1 Component without relay installed
(Engine Room Relay Block Assembly)



OK

15.CHECK HARNESS AND CONNECTOR (HEATER RELAY - COMPRESSOR WITH MAGNET CLUTCH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.CHECK HARNESS AND CONNECTOR (HEATER RELAY - COMPRESSOR WITH MAGNET CLUTCH)
a.

Disconnect the C17 compressor with magnet clutch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C17-1(MG+) - 3 Always Below 1 Ω
C17-1(MG+) - Body ground Always 10 kΩ or higher




OK

16.INSPECT COMPRESSOR WITH MAGNET CLUTCH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.INSPECT COMPRESSOR WITH MAGNET CLUTCH
a.

Inspect the compressor with magnet clutch (See page Vehicle Interior>HEATING / AIR CONDITIONING>COMPRESSOR>INSPECTION).



OK

17.CHECK HARNESS AND CONNECTOR (HEATER RELAY - AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY)

NG

REPLACE COMPRESSOR WITH MAGNET CLUTCH

17.CHECK HARNESS AND CONNECTOR (HEATER RELAY - AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY)
a.

Disconnect the A7 air conditioner tube and accessory assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 - A7-1(AC) Always Below 1 Ω
2 - Body ground Always 10kΩ or higher




OK

18.CHECK HARNESS AND CONNECTOR (HEATER RELAY - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.CHECK HARNESS AND CONNECTOR (HEATER RELAY - ECM)
a.
E234483E01
0.171,0.402 0.333,0.588 0.163,0.186 10 *1

Disconnect the A35 ECM connector.


b.

Measure the resistance according to the valve(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - A35-35(AC) Always Below 1 Ω
1 - Body ground Always 10kΩ or higher


Text in Illustration
*1 Component without relay installed
(Engine Room Relay Block Assembly)



OK

REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR