Home › Vehicle Interior › INTERIOR PANELS / TRIM › LOWER INSTRUMENT PANEL › from 2016.06
RM2090E _58 Vehicle Interior _060706 INTERIOR PANELS / TRIM _0297756 LOWER INSTRUMENT PANEL A

INTERIOR PANELS / TRIM  LOWER INSTRUMENT PANEL  REMOVAL  


PROCEDURE

Hide 1. TABLE OF BOLT, SCREW AND NUT

a.

All bolts, screws and nuts relevant to installing and removing the instrument panel are shown along with an alphabetical code in the table.

B313719E02
3.833,2 4.51,2.417 0.677,0.417 10 false Length=7 (0.276 in) 3.844,1.25 4.458,1.625 0.615,0.375 10 false φ=10 (0.394 in) 1.615,2.031 2.323,2.448 0.708,0.417 10 false Length=16 (0.630 in) 1.615,1.271 2.292,1.677 0.677,0.406 10 false φ=11.5 (0.453 in) 0.188,0.844 0.76,1.156 0.573,0.313 10 false Code 1.323,0.854 2.302,1.198 0.979,0.344 10 false Shape 2.531,1.719 3.208,2.188 0.677,0.469 10 false <B> 0.229,1.719 1.083,2.177 0.854,0.458 10 false <A> 2.448,0.833 3.021,1.146 0.573,0.313 10 false Code 3.542,0.823 4.521,1.167 0.979,0.344 10 false Shape


Hide 2. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 58810J 4.REMOVE CONSOLE BOX ASSEMBLY

Hide 55461A 5.REMOVE INSTRUMENT PANEL ORNAMENT (w/ Large Ornament Panel)

a.
B458376E01
1.427,1.958 1.604,1.688 false 1.229,1.885 1.552,2.146 0.323,0.26 10 false *1

Using a moulding remover, disengage the 8 clips and 2 claws to remove the instrument panel ornament.

Text in Illustration
*1 Moulding Remover


Hide 55405B 6.REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (w/o Large Ornament Panel)

a.
B315188E01
2.896,3.104 3.01,2.854 false 2.729,3.073 3.135,3.302 0.406,0.229 10 false *1

Using a moulding remover, disengage the 2 claws and 4 clips to remove the center instrument cluster finish panel sub-assembly.

Text in Illustration
*1 Moulding Remover


Hide 7.REMOVE STEREO OPENING COVER WITH BRACKET (w/o Radio Receiver)

a.
B315189

Remove the 4 screws to remove the stereo opening cover with bracket.


Hide 8.REMOVE RADIO RECEIVER ASSEMBLY WITH BRACKET (w/ Radio Receiver)

Hide 55475A 9.REMOVE NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH

a.
B313970

Remove the screw.


b.

Disengage the 6 claws to remove the No. 2 instrument cluster finish panel garnish.


Hide 55044B 10.REMOVE UPPER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY (for LH Side)

a.
B319321

Remove the screw.


b.

Disengage the 3 claws to remove the upper instrument panel finish panel sub-assembly.


Hide 55474C 11.REMOVE NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH

HINT:

Use the same procedure as for the No. 2 instrument cluster finish panel garnish.


Hide 55045C 12.REMOVE UPPER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY (for RH Side)

HINT:

Use the same procedure as for the LH side.


Hide 55900 13.REMOVE AIR CONDITIONING CONTROL ASSEMBLY (for Automatic Air Conditioning System)

Hide 55900 14.REMOVE AIR CONDITIONING CONTROL ASSEMBLY (for Manual Air Conditioning System)

Hide 55900 15.REMOVE AIR CONDITIONING CONTROL ASSEMBLY (w/o Air Conditioning System)

HINT:

Use the same procedure as for the manual air conditioning system.


Hide 55317A 16.REMOVE INSTRUMENT SIDE PANEL RH (w/ Airbag Cut Off Switch)

a.
B316757E01
2.699,1.723 2.869,1.879 0.170,0.156 10 *1 2.268,1.818 2.686,1.819 false

Using a moulding remover, disengage the claw and 4 clips.

Text in Illustration
*1 Moulding Remover


b.

Disconnect the connector and remove the instrument side panel RH.


Hide 55317A 17.REMOVE INSTRUMENT SIDE PANEL RH (w/o Airbag Cut Off Switch)

a.
B310185E01
2.6,1.78 2.772,1.950 0.173,0.170 10 *1 2.26,1.806 2.567,1.869 false

Using a moulding remover, disengage the claw and 4 clips and remove the instrument side panel RH.

Text in Illustration
*1 Moulding Remover


Hide 55318C 18.REMOVE INSTRUMENT SIDE PANEL LH

HINT:

Use the same procedure as for the RH side.


Hide 55403 19.REMOVE METER HOOD SUB-ASSEMBLY

a.
B315191

Remove the screw.


b.

Disengage the 12 claws, and then pull out the meter hood sub-assembly diagonally upwards to remove it.


Hide 55422 20.REMOVE UPPER INSTRUMENT PANEL METER ORNAMENT

a.
B316758

Disengage the 6 claws and 2 clips.


b.
B316759

Disengage the 2 claws that are holding the upper instrument panel meter ornament and steering column cover together.


c.

Disconnect the connector and remove the upper instrument panel meter ornament.


Hide 55606 21.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/ Knee Airbag)

Hide 55607 22.REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/ Knee Airbag)

a.

for LHD

i.

Remove the screw.


ii.
E252256

Disengage the 3 claws and 4 clips and remove the No. 2 instrument panel under cover sub-assembly .



b.
E252255

for RHD

i.

Remove the screw.


ii.

Disengage the 3 claws and 4 clips.


iii.

Disconnect the cooler thermistor hose and connector and remove the No. 2 instrument panel under cover sub-assembly .



Hide 55550 23.REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY

a.
B315192E01
3.17,0.049 3.346,0.226 0.177,0.177 10 *1 2.994,0.636 3.222,0.231 false

Disengage the claw and release the glove compartment door damper.

Text in Illustration
*1 Glove Compartment Door Damper


b.
B315193E01
0.052,0.749 0.218,0.916 0.166,0.167 10 *1 3.006,1.014 3.173,1.182 0.166,0.167 10 *1 0.345,0.398 0.172,0.729 false 3.064,0.657 3.085,1.011 false

Release the 2 stoppers and open the glove compartment door assembly until it is horizontal.

Text in Illustration
*1 Stopper


c.

Pull the glove compartment door assembly horizontally backward to disengage the 2 hinges and remove the glove compartment door assembly.

NOTICE:

Be sure to pull the glove compartment door assembly horizontally to remove it.



Hide 55557C 24.REMOVE GLOVE COMPARTMENT DOOR DAMPER

a.
B315194

Disengage the claw and remove the glove compartment door damper.


Hide 55303B 25.REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY

a.
B315196

Remove the 7 screws.


b.
B315195

Remove the 2 screws and nut.


c.

Disconnect the connectors.


d.

Disconnect the aspirator pipe from the air conditioning unit assembly (for LHD with Automatic Air Conditioning System).


e.

Disengage the 12 claws and clamp to remove the lower instrument panel sub-assembly.

B315197E01
0.853,4.307 1.031,4.471 0.178,0.163 10 *1 1.014,4.363 1.494,4.244 false

Text in Illustration
*1 DLC3 - -