Home › Vehicle Exterior › WINDOW / GLASS › BACK WINDOW GLASS
RM2090E _59 Vehicle Exterior _060707 WINDOW / GLASS _0297763 BACK WINDOW GLASS A

WINDOW / GLASS  BACK WINDOW GLASS  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

Use the same procedure for the LHD and RHD vehicle.


PROCEDURE

Hide 75571G 1.INSTALL NO. 1 BACK WINDOW MOULDING

a.
B309184E01
2.707,0.276 2.833,0.448 0.126,0.172 10 a

Using a brush or sponge, coat the application area of a new No. 1 back window moulding with Primer (3M N-200), as shown in the illustration.

Standard Dimension:
Area Measurement
a 4.0 mm (0.1575 in.)


Text in Illustration
V100145

Primer (3M N-200)


b.
B309185E02
2.521,0.292 2.635,0.458 0.115,0.167 10 false a 3.302,0.792 3.417,0.958 0.115,0.167 10 false b

Install the new double sided tape onto the No. 1 back window moulding, as shown in the illustration.

Standard Dimension:
Area Measurement
a 4.0 mm (0.1575 in.)
b 1.0 mm (0.0394 in.)


Text in Illustration
V100155

Double Sided Tape
V100145

Primer (3M N-200)


c.

Using a brush or sponge, coat the application area of a new No. 1 back window moulding with Primer (3M N-200).

NOTICE:
·

Do not apply too much primer.

·

Allow the primer coating to dry for 3 minutes or more.

·

Throw away any leftover primer.



HINT:

If an area other than specified is coated by accident, wipe off the primer with a clean piece of cloth before it dries.



d.
B309186E01
0.071,0.02 0.277,0.183 0.206,0.163 10 *a

Using a roller, install the new No. 1 back window moulding onto the back window glass, as shown in the illustration.

Text in Illustration
*a Back Side

NOTICE:

Install the No. 1 back window moulding firmly so that it does not sag.



e.
B309187E01
0.101,0.083 0.276,0.237 0.175,0.154 10 *a

Using a roller, install the No. 1 back window moulding onto the back window glass, as shown in the illustration.

Text in Illustration
*a Back Side

NOTICE:

Install the No. 1 back window moulding firmly so that it does not sag.



Hide 64813D 2.INSTALL BACK WINDOW GLASS ADHESIVE DAM

a.

Using a brush or sponge, coat the application area of a new back window glass adhesive dams with Primer (3M-N200).

NOTICE:
·

Allow the primer coating to dry for 3 minutes or more.

·

Do not apply too much primer.

·

Do not keep any of the opened Primer for later use.



HINT:

If any area other than the specified is coated by accident, wipe off the primer with a clean piece of cloth before it dries.



b.

Install the new back window glass adhesive dams onto the back window glass, as shown in the illustration.

B309188E02
4.75,1.323 4.51,1.49 true 6.271,1.313 6.49,1.688 false 4.635,3.563 4.417,3.104 true 1.74,3.979 1.938,4.021 1.938,4.021 1.792,4.302 false 1.896,0.167 2.01,0.344 0.115,0.177 10 false a 5.938,0.698 6.052,0.875 0.115,0.177 10 false c 4.479,3.927 4.594,4.104 0.115,0.177 10 false d 4.688,0.625 4.802,0.802 0.115,0.177 10 false b 0.198,0.083 0.365,0.26 0.167,0.177 10 false *a 4.365,1.448 4.531,1.625 0.167,0.177 10 false *1 2.26,1.177 2.375,1.354 0.115,0.177 10 false A 0.208,2.333 0.323,2.51 0.115,0.177 10 false B 2.26,3.438 2.396,3.615 0.135,0.177 10 false C 3.958,2.469 4.229,2.646 0.271,0.177 10 false C-C 3.948,0.063 4.219,0.24 0.271,0.177 10 false A-A 5.604,0.063 5.875,0.24 0.271,0.177 10 false B-B 2.26,2.906 2.396,3.083 0.135,0.177 10 false C 2.25,1.729 2.365,1.906 0.115,0.177 10 false A 0.75,2.323 0.865,2.5 0.115,0.177 10 false B 1.167,0.406 1.281,0.583 0.115,0.177 10 false a 1.823,4.469 1.938,4.646 0.115,0.177 10 false a 1.167,3.906 1.281,4.083 0.115,0.177 10 false a 6.448,1.708 6.615,1.885 0.167,0.177 10 false *1 4.333,2.938 4.5,3.115 0.167,0.177 10 false *1 1.979,3.927 2.146,4.104 0.167,0.177 10 false *2

Standard Dimension:
Area Dimension
a 0.0 to 3.0 mm (0 to 0.1181 in.)
b 19.9 to 21.9 mm (0.7835 to 0.8622 in.)
c 18.9 to 20.9 mm (0.7441 to 0.8228 in.)
d 6.0 to 8.0 mm (0.2362 to 0.3150 in.)


Text in Illustration
*1 Back Window Glass Adhesive Dam *2 Ceramic Notch
*a Back Side - -

HINT:

Use the same procedure for both the RH and LH sides.



Hide 64811 3.INSTALL BACK WINDOW GLASS

a.
B309177E03
2.073,0.76 1.771,0.76 true 1.771,0.5 1.927,0.5 1.927,0.5 1.927,0.75 true 2.115,0.667 2.271,0.813 0.156,0.146 10 false *a

Position the back window glass.

Text in Illustration
*a Matchmark

i.

Using suction cups, place the back window glass in the correct position.


ii.

Check that the whole contact surface of the back window glass rim is perfectly even.


iii.

Align the matchmarks on the back window glass and vehicle body.

NOTICE:

Check that the back window glass stoppers are correctly attached to the vehicle body.



iv.

Remove the back window glass.



b.
B295410E01
0.994,0.078 1.236,0.270 0.242,0.191 10 *a 2.524,0.078 2.766,0.270 0.242,0.191 10 *b

Using a brush, coat the installation surface on the vehicle body with Primer (sunstar #435-40).

Text in Illustration
*a NG
*b OK
V100145

Primer (sunstar #435-40)
V100155

Adhesive

NOTICE:
·

Do not coat the adhesive with Primer.

·

Do not apply too much primer.



HINT:

If any area other than the specified is coated by accident, wipe off the primer with a clean piece of cloth before it dries.



c.

Using a brush or sponge, coat the adhesive application area with Primer (3M N-200).

B309189E02
6.083,0.802 5.927,1.156 true 4.781,0.948 5.135,0.813 true 6.229,0.802 6.469,1.146 false 6.188,2.688 6.083,2.313 true 6.385,2.802 6.76,2.99 false 4.677,2.865 4.927,3.021 false 4.521,2.771 4.448,2.292 true 4.448,2.292 4.375,2.708 true 4.646,0.969 4.396,1.25 true 1.75,0.594 1.875,0.76 0.125,0.167 10 false A 0.667,1.854 0.792,2.021 0.125,0.167 10 false B 1.75,2.448 1.875,2.615 0.125,0.167 10 false C 0.573,2.333 0.698,2.5 0.125,0.167 10 false D 4.688,0.375 4.813,0.542 0.125,0.167 10 false a 5.979,0.229 6.104,0.396 0.125,0.167 10 false a 6.021,3.031 6.146,3.198 0.125,0.167 10 false a 4.146,3.031 4.271,3.198 0.125,0.167 10 false a 4.271,3.135 4.396,3.302 0.125,0.167 10 false a 4.375,2.125 4.542,2.292 0.167,0.167 10 false *2 4.229,1.177 4.396,1.344 0.167,0.167 10 false *2 5.823,1.167 5.99,1.333 0.167,0.167 10 false *2 6.021,2.125 6.188,2.292 0.167,0.167 10 false *2 4.948,3.01 5.115,3.177 0.167,0.167 10 false *1 5.146,0.698 5.313,0.865 0.167,0.167 10 false *1 6.438,1.146 6.604,1.313 0.167,0.167 10 false *1 6.781,2.979 6.948,3.146 0.167,0.167 10 false *1 3.885,0.073 4.156,0.24 0.271,0.167 10 false A-A 5.615,0.063 5.885,0.229 0.271,0.167 10 false B-B 5.604,1.938 5.875,2.104 0.271,0.167 10 false C-C 3.875,1.938 4.146,2.104 0.271,0.167 10 false D-D 0.167,0.115 0.333,0.281 0.167,0.167 10 false *a 1.74,1.146 1.865,1.313 0.125,0.167 10 false A 1.76,3 1.885,3.167 0.125,0.167 10 false C 0.104,1.854 0.229,2.021 0.125,0.167 10 false B 0.385,2.844 0.51,3.01 0.125,0.167 10 false D

Standard Dimension:
Area Dimension
a 8.0 mm (0.315 in.)


Text in Illustration
*1 Back Window Glass Adhesive Dam *2 Primer (3M N-200)
*a Back Side - -

NOTICE:
·

Do not apply too much primer.

·

Allow the primer coating to dry for 3 minutes or more.



HINT:

If any area other than the specified is coated by accident, wipe off the primer with a clean piece of cloth before it dries.



d.

Apply adhesive to the glass.

Adhesive:

Toyota Genuine Windshield Glass Adhesive or equivalent


i.
B214800E09
0.583,0.635 0.74,0.833 0.156,0.198 10 a 1.313,1.427 1.469,1.625 0.156,0.198 10 a 1.115,0.875 1.271,1.073 0.156,0.198 10 b 0.75,1.01 0.906,1.208 0.156,0.198 10 b

Cut off the tip of the cartridge nozzle, as shown in the illustration.

Standard Dimension:
Area Dimension
a 12.0 mm (0.472 in.)
b 8.0 mm (0.315 in.)



ii.

Load the sealer gun with the cartridge.


iii.

Apply adhesive to the back window glass, as shown in the illustration.

B309190E02
4.594,1.063 4.313,1.094 false 4.76,1.052 4.552,1.281 true 6.198,0.833 6.115,1.24 true 6.073,0.865 5.896,1.094 false 6.292,2.865 6.094,3.198 true 6.135,2.833 5.813,2.958 false 4.583,2.917 4.281,3.24 true 4.281,2.875 4.031,3.094 4.031,3.094 4.427,2.917 false 0.208,0.052 0.375,0.208 0.167,0.156 10 false *a 4.688,0.396 4.802,0.563 0.115,0.167 10 false a 4.958,0.74 5.073,0.906 0.115,0.167 10 false b 4.417,1.198 4.583,1.365 0.167,0.167 10 false *1 4.125,1.021 4.292,1.188 0.167,0.167 10 false *2 1.771,0.573 1.885,0.74 0.115,0.167 10 false A 1.771,1.146 1.885,1.313 0.115,0.167 10 false A 0.125,1.844 0.24,2.01 0.115,0.167 10 false B 0.677,1.844 0.792,2.01 0.115,0.167 10 false B 1.75,2.458 1.896,2.625 0.146,0.167 10 false C 1.75,3 1.896,3.167 0.146,0.167 10 false C 0.406,2.802 0.531,2.969 0.125,0.167 10 false D 0.573,2.313 0.698,2.479 0.125,0.167 10 false D 3.875,1.948 4.156,2.115 0.281,0.167 10 false D-D 5.594,1.948 5.875,2.115 0.281,0.167 10 false C-C 5.604,0.083 5.885,0.25 0.281,0.167 10 false B-B 3.875,0.073 4.156,0.24 0.281,0.167 10 false A-A 4.427,2.354 4.542,2.521 0.115,0.167 10 false a 4.677,2.229 4.792,2.396 0.115,0.167 10 false a 4.677,2.948 4.792,3.115 0.115,0.167 10 true b 4.156,3.281 4.323,3.448 0.167,0.167 10 false *1 3.875,3.063 4.042,3.229 0.167,0.167 10 false *2 6.344,2.146 6.458,2.313 0.115,0.167 10 false a 6.51,2.854 6.625,3.021 0.115,0.167 10 false b 5.948,3.208 6.115,3.375 0.167,0.167 10 false *1 5.646,2.906 5.813,3.073 0.167,0.167 10 false *2 5.979,0.219 6.094,0.385 0.115,0.167 10 false a 6.354,0.875 6.469,1.042 0.115,0.167 10 false b 6.01,1.271 6.177,1.438 0.167,0.167 10 false *1 5.74,1.052 5.906,1.219 0.167,0.167 10 false *2

Standard Dimension:
Area Dimension
a 8.0 mm (0.315 in.)
b 12.0 mm (0.472 in.)


Text in Illustration
*1 Back Window Glass Adhesive Dam *2 Adhesive
*a Back Side - -



e.
B309177E03
2.073,0.76 1.771,0.76 true 1.771,0.5 1.927,0.5 1.927,0.5 1.927,0.75 true 2.115,0.667 2.271,0.813 0.156,0.146 10 false *a

Apply adhesive tape, etc. to the back window glass and the body panel section, and use a pen to apply matching marks for use when installing (when using the new back window glass).

Text in Illustration
*1 Matchmark

i.

Using suction cups, position the back window glass so that the matchmarks are aligned, and press it in gently along the rim.

NOTICE:
·

Check that the back window glass stopper are attached to the vehicle body correctly.

·

Check the clearance between the vehicle body and back window glass.

·

After the primer on the body is dried (about 10 minutes), install the back window glass.




ii.

Lightly press the front surface of the back window glass to ensure that the back window glass is securely fit to the vehicle body.

HINT:

Press the glass with force of 98 N (10 kgf, 22.0 lbf) or more.



iii.

Using a scraper, remove any excess or protruding adhesive.

HINT:

Apply adhesive onto the back window glass rim.



iv.

Hold the back window glass using protective tape until the applied adhesive becomes hard.

HINT:

Follow the instructions in the owner's manuals provided by each adhesive manufacturer regarding the minimum required drying time after applying adhesive, and the time required before driving.




f.

Connect each connector.


Hide 4.INSPECT WATER LEAK

a.

After the adhesive has hardened, apply water from the outside of the vehicle. Check that no water leaks into the cabin.


b.

If water leaks into the cabin, allow the water to dry and add adhesive.


c.

Remove the protective tape.


Hide 64330 5.INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY

Hide 62462A 6.INSTALL REAR WINDOW SIDE GARNISH LH

Hide 62461A 7.INSTALL REAR WINDOW SIDE GARNISH RH

HINT:

Use the same procedure as for the LH side.


Hide 62606A 8.INSTALL QUARTER TRIM LID SUB-ASSEMBLY LH

Hide 62605Q 9.INSTALL QUARTER TRIM LID SUB-ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 64715D 10.INSTALL LUGGAGE COMPARTMENT TRIM COVER LH

Hide 64714D 11.INSTALL LUGGAGE COMPARTMENT TRIM COVER RH

HINT:

Use the same procedure as for the LH side.


Hide 64722 12.INSTALL LUGGAGE COMPARTMENT INNER TRIM COVER LH

Hide 64721 13.INSTALL LUGGAGE COMPARTMENT INNER TRIM COVER RH

HINT:

Use the same procedure as for the LH side.


Hide 62312B 14.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

Hide 62311B 15.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedure as for the LH side.


Hide 67913 17.INSTALL FRONT DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.


Hide 71470S 18.INSTALL SEPARATE TYPE REAR SEAT CUSHION ASSEMBLY LH

Hide 71460S 19.INSTALL SEPARATE TYPE REAR SEAT CUSHION ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.