Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM
RM2090E _59 Vehicle Exterior _060707 WINDOW / GLASS _0297766 POWER WINDOW CONTROL SYSTEM J

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  Key-off Operation Function Operates even if Operating Conditions are not Satisfied  


DESCRIPTION

When the driver door has not been opened and fully closed, driver door power window regulator motor can control its power window operation for approximately 45 seconds after the ignition switch is turned from ON to off (the key is removed) by receiving operation permission signals from the main body ECU (network gateway ECU). However, when approximately 45 seconds have elapsed, or the driver door is opened within approximately 45 seconds after turning the ignition switch off (the key is removed), the power window regulator motor stops operating.

During the AUTO function operation, the window operation will continue until complete even if 45 seconds have elapsed or a door is opened.

NOTICE:
·

When the power window regulator master switch assembly, power window regulator switch assembly and power window regulator motor assembly is reinstalled or replaced, the power window control system must be initialized (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION).

·

When the jam protection function malfunctions and prevents the door glass from closing completely, the following procedure can be used to cancel the jam protection function and allow the door glass to be closed*1.

-

Repeat the AUTO UP maintain → jam protection function operation twice in succession*2.

-

The third repeat of the AUTO UP maintain operation will cause the position of the upper edge of the door glass to be relearned, allowing the door glass to be closed.

*1: In some cases, the state of the door glass or regulator may prevent the glass from being closed, even in this mode.

*2: If any action other that the AUTO UP operation (DOWN operation, IG OFF, timer-operated OFF, index operation, etc.) is performed between the operation of the jam protection function and the AUTO UP maintain, this count will be reset.






PROCEDURE

1.CHECK OPERATION FUNCTION AFTER IGNITION SWITCH IS TURNED OFF
a.

Check the power window master switch assembly operation function after the ignition switch is turned off.

Result
Result Proceed to
When power window can still be operated even after opening driver door within approximately 45 seconds of ignition switch being turned off A
When power window can still be operated even after approximately 45 seconds have elapsed after ignition switch turned off (for All Doors) B
When power window can still be operated even after approximately 45 seconds have elapsed after ignition switch turned off (for Driver Side) B


b.

Check the power window switch assembly operation function after the ignition switch is turned off.

Result
Result Proceed to
When power window can still be operated even after opening driver door within approximately 45 seconds of ignition switch being turned off C
When power window can still be operated even after approximately 45 seconds have elapsed after ignition switch turned off (for Front Passenger Side) D



A

2.READ VALUE USING GTS (DOOR COURTESY SWITCH)

B

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

C

3.READ VALUE USING GTS

D

4.CHECK OPERATION (POWER WINDOW SWITCH)
2.READ VALUE USING GTS (DOOR COURTESY SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Master Switch / Data List.


e.

According to the display on the GTS, read the Data List.

Master Switch
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
D Door Courtesy SW Driver side door courtesy light switch signal / ON or OFF ON: Driver side door opened
OFF: Driver side door closed
-

OK:

Normal conditions listed above are displayed.




OK

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

NG

GO TO LIGHTING SYSTEM (Door Courtesy Switch Circuit)

3.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Master Switch / Data List.


e.

According to the display on the GTS, read the Data List.

Master Switch
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
P Door Courtesy SW Front passenger side door courtesy light switch signal / ON or OFF OK: Front passenger side door opened
NG: Front passenger side door closed
-

OK:

Normal conditions listed above are displayed.




OK

REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY

NG

GO TO LIGHTING SYSTEM (Door Courtesy Switch Circuit)

4.CHECK OPERATION (POWER WINDOW SWITCH)
a.

Check the power window regulator master switch assembly and power window regulator switch assembly operation function after the ignition switch is off.

Result
Result Proceed to
Operate (for both driver side and front passenger side switches) A
Operate (for driver side switch only) A
Operate (for front passenger side switch only) B



A

5.REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

B

6.REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY
5.REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
a.

Remove the power window regulator master switch assembly (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>REMOVAL).


b.

Check the power window regulator master switch assembly operates (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>OPERATION CHECK).

OK:

Driver door power window operates normally.



Result
Result Proceed to
Does not operate A
Operate B


A

REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY

B

END

6.REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY
a.

Remove the power window regulator switch assembly (See page Vehicle Exterior>WINDOW / GLASS>FRONT PASSENGER SIDE POWER WINDOW SWITCH>REMOVAL).


b.

Check the power window regulator switch assembly operates (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>OPERATION CHECK).

OK:

Front passenger side door power window operates normally.



Result
Result Proceed to
Does not operate A
Operate B


A

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

B

END