Home › Vehicle Exterior › DOOR / HATCH › FRONT DOOR
RM2090E _59 Vehicle Exterior _060708 DOOR / HATCH _0297771 FRONT DOOR A

DOOR / HATCH  FRONT DOOR  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:

Use the same procedure for both the RH and LH sides.


PROCEDURE

Hide 67811C 1.INSTALL FRONT DOOR HOLE COVER

a.
B314813

Insert the front door hole cover with the 4 claws.


Hide 68210C 3.INSTALL FRONT DOOR GLASS OUTER WEATHERSTRIP ASSEMBLY

Hide 67001A 4.INSTALL FRONT DOOR PANEL CUSHION

a.
B314812

Engage the 2 claws and install 2 new front door panel cushions.


Hide 68620 5.INSTALL FRONT DOOR CHECK ASSEMBLY

a.

Apply MP grease to the sliding areas of the front door check assembly.


b.
B314811

Apply adhesive to the threads of the bolt.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



c.

Install the bolt.

Torque:
33 N*m (337 kgf*cm, 24 ft.*lbf)


d.

Install the front door check assembly with the 2 nuts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 69312 6.INSTALL FRONT DOOR LOCK OPEN ROD

a.
B314814E01
2.535,0.35 2.639,0.496 0.104,0.146 10 1 1.684,0.174 1.789,0.321 0.104,0.146 10 2

Install the front door lock open rod as indicated by the arrows, in the order shown in the illustration.


Hide 69202A 7.INSTALL FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY

a.

Apply MP grease to the sliding parts on the front door outside handle frame sub-assembly.


b.
B314815E01
0.206,0.246 0.408,0.430 0.202,0.184 10 *a 0.2,2.338 0.402,2.521 0.202,0.184 10 *b

Engage the claw.


c.

Using a T30 "TORX" socket wrench, install the front door outside handle frame sub-assembly with the screw.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)

Text in Illustration
*a Outside Vehicle
*b Inside Vehicle


Hide 69241H 8.INSTALL FRONT DOOR FRONT OUTSIDE HANDLE PAD

a.
B314807

Engage the 3 claws and install the front door front outside handle pad.


Hide 69242E 9.INSTALL FRONT DOOR REAR OUTSIDE HANDLE PAD

a.
B314808

Engage the 2 claws and install the front door rear outside handle pad.


Hide 69220 10.INSTALL FRONT DOOR OUTSIDE HANDLE ASSEMBLY (w/ Entry and Start System)

a.
B314816

Insert the front end of the front door outside handle assembly into the front door outside handle frame sub-assembly.


b.

Insert the rear end of the front door outside handle assembly into the front door outside handle frame sub-assembly, and then slide the front door outside handle assembly toward the front of the vehicle to install it.


c.
B314817

Connect the connector.


d.

Engage the 3 claws.


e.
B314805

Engage the clamp.


Hide 69220 11.INSTALL FRONT DOOR OUTSIDE HANDLE ASSEMBLY (w/o Entry and Start System)

a.
B314816

Insert the front end of the front door outside handle assembly into the front door outside handle frame sub-assembly.


b.

Insert the rear end of the front door outside handle assembly into the front door outside handle frame sub-assembly, and then slide the front door outside handle assembly toward the front of the vehicle to install it.


Hide 69320 12.INSTALL FRONT DOOR LOCK ASSEMBLY

Hide 69217F 13.INSTALL FRONT DOOR OUTSIDE HANDLE COVER (for Driver Side)

a.
B228719

Engage the claw and 2 guides, and install the front door outside handle cover to the front door lock cylinder assembly.


Hide 69510 14.INSTALL FRONT DOOR LOCK CYLINDER ASSEMBLY (for Driver Side)

a.
B314818

Install the front door outside handle cover with front door lock cylinder assembly.

HINT:

Make sure that the front door lock cylinder rod is inserted into the front door lock assembly.



b.
B314802

Using a T30 "TORX" socket wrench, install the front door lock cylinder assembly with the screw.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 69217E 15.INSTALL FRONT DOOR OUTSIDE HANDLE COVER (for Front Passenger Side)

a.
B314803

Using a T30 "TORX" socket wrench, install the front door outside handle cover with the screw.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 67862 16.INSTALL FRONT DOOR WEATHERSTRIP

a.

Engage the 16 clips.


b.

Engage the claw.


c.

Install the front door weatherstrip with the screw.

B314801


Hide 85720D 17.INSTALL POWER WINDOW REGULATOR MOTOR ASSEMBLY

Hide 69802 18.INSTALL FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY

a.

Apply MP grease to the sliding parts of the front door window regulator sub-assembly.


b.

Install the temporary bolt to the front door window regulator sub-assembly.


c.
B314800E01
1.101,0.569 1.251,0.725 0.150,0.156 10 *1 1.284,0.683 1.999,0.891 false

Temporarily install the front door window regulator sub-assembly.


d.

Tighten the 3 bolts and 2 nuts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


e.

Tighten the temporary bolt.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


f.

Connect the connector.

Text in Illustration
*1 Temporary Bolt


Hide 62616 19.INSTALL FRONT DOOR SASH STOPPER

a.

Install the front door sush stopper with the bolt.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 67402F 20.INSTALL FRONT DOOR SUSH

a.
B314820E01
2.027,0.339 2.220,0.503 0.192,0.164 10 (2) 0.878,0.82 1.071,0.984 0.192,0.164 10 (1)

Insert the front door sush so that it is perpendicular to the front door frame, in the order shown in the illustration.


b.

Rotate the front door sush 90°.

NOTICE:

Do not damage the front door sush.



c.
B314797E03
1.938,1.875 2.146,2.052 0.208,0.177 10 true (A) 2.51,0.958 2.719,1.135 0.208,0.177 10 true (B) 1.719,0.969 1.927,1.146 0.208,0.177 10 true (B)

Install the front door sush with the 3 nuts.

Torque:
Nut(A) : 14 N*m (143 kgf*cm, 10 ft.*lbf)

Torque:
Nut(B) : 7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 68102 21.INSTALL FRONT DOOR GLASS SUB-ASSEMBLY

a.

Connect the cable to the negative (-) battery terminal.


b.

Connect the power window regulator master switch assembly connector (for driver side).


c.

Connect the power window regulator switch assembly connector (for front passenger side).


d.

Move the front door glass sub-assembly until the 2 nuts can be seen through the service holes.


e.

Disconnect the cable from the negative (-) battery terminal.


f.

Disconnect the power window regulator master switch assembly connector (for driver side).


g.

Disconnect the power window regulator switch assembly connector (for front passenger side).


h.
B314796

Insert the front door glass sub-assembly into the front door frame from the position indicated in the illustration.

NOTICE:

Do not damage the front door weatherstrip.


HINT:

The front door glass sub-assembly can only be installed from the position indicated in the illustration, so install it while sliding the front door rear lower frame sub-assembly.



i.

Insert the grommet of front door glass assembly into the rail of the front door rear lower frame sub-assembly.


j.
B386126E03
2.125,0.406 2.021,0.281 false 2.5,0.615 2.635,0.427 false 2.49,1.115 2.635,1.094 false 2.208,1.115 1.979,1.115 false 2.021,0.635 1.813,0.615 false 1.375,3.75 1.188,3.938 true 1.573,2.177 1.24,1.271 true 1.094,3.948 1.26,4.115 0.167,0.167 10 false *a 1.677,0.177 1.979,0.344 0.302,0.167 10 false SST 2.708,1.563 2.875,1.729 0.167,0.167 10 true *1 0.583,2.906 0.75,3.073 0.167,0.167 10 true *2 2.646,1 2.813,1.167 0.167,0.167 10 false *3 1.781,1.031 1.948,1.198 0.167,0.167 10 false *4 1.625,0.521 1.792,0.688 0.167,0.167 10 false *1 2.646,0.313 2.813,0.479 0.167,0.167 10 false *5 0.906,1.167 1.208,1.333 0.302,0.167 10 false SST

Install a new nut B temporarily to the front door glass sub-assembly.

Text in Illustration
*1 Nut A
*2 Nut B
*3 Front Door Glass Sub-assembly
*4 Front Door Window Regulator Sub-assembly
*5 Bolt
*a SST Number


k.

Install SST as shown in the illustration.

SST
09801-18010  

HINT:

The SST number on SST must be visible.



l.

Secure the bolt using SST, and then tighten a new nut A to the specified torque.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


m.

Tighten nut B to the specified torque.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 67241A 22.INSTALL DOOR GLASS INNER STABILIZER

a.

Install the door glass inner stabilizer with the bolt.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 67404F 23.INSTALL FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY

a.

Install the front door rear lower frame sub-assembly with the 3 nuts.

Torque:
14 N*m (143 kgf*cm, 10 ft.*lbf)


Hide 87906B 24.INSTALL OUTER REAR VIEW MIRROR SUB-ASSEMBLY

Hide 68102 25.ADJUST FRONT DOOR GLASS SUB-ASSEMBLY

a.

Check the front door glass sub-assembly (See page Vehicle Exterior>DOOR / HATCH>FRONT DOOR>ADJUSTMENT).


b.

Adjust the front door glass sub-assembly (See page Vehicle Exterior>DOOR / HATCH>FRONT DOOR>ADJUSTMENT).


Hide 67832 26.INSTALL FRONT DOOR SERVICE HOLE COVER

a.

Apply butyl tape to the front door panel.


b.

Pass the front door lock remote control cable assembly and the front door inside locking cable assembly through a new front door service hole cover.

B314821E01
1.238,0.567 1.421,0.722 0.183,0.156 10 *1 5.933,0.491 6.116,0.647 0.183,0.156 10 *1

Text in Illustration
*1 Reference Point - -


c.

Attach the front door service hole cover according to the reference points on the front door panel.

NOTICE:
·

Overlay the butyl tape in lengths of 20 cm (7.874 in.) or more.

·

Do not block the drip holes in the front door panel with butyl tape.

·

Securely install the front door service hole cover preventing wrinkles and air bubbles.




d.

Connect each connector.


Hide 86160 27.INSTALL FRONT NO. 1 SPEAKER ASSEMBLY (w/ Front Speaker)

Hide 67835 28.INSTALL FRONT DOOR SPEAKER HOLE COVER (w/o Front Speaker)

a.
B309247

Install the front door speaker hole cover with the 3 screws.


Hide 68172A 29.INSTALL FRONT DOOR GLASS INNER WEATHERSTRIP

a.
B373753

Engage the 9 claws to install a new front door glass inner weatherstrip to the front door trim board sub-assembly as shown in the illustration.


b.
B314823

Install a nose piece to an air riveter, and then insert the mandrel part of a new rivet into the nose piece.


c.

Hold the riveter perpendicular against the moulding and install the 6 rivets.

HINT:

If the rivet cannot be cut, pull it once again to cut it. Also, be sure to cut off the head.


NOTICE:
·
B171664E63
1.229,1.104 1.083,1.635 1.083,1.635 1.24,2.198 false 1.083,1.635 0.813,1.635 false 1.771,0.917 2.01,1.656 2.01,1.656 1.792,2.521 false 2.021,1.656 2.302,1.656 false 2.271,0.604 2.469,0.802 0.198,0.198 10 false *a 2.271,2.469 2.49,2.667 0.219,0.198 10 false *b 0.594,1.563 0.781,1.76 0.188,0.198 10 false *1 2.354,1.563 2.542,1.74 0.188,0.177 10 false *2

Do not pry the rivet with the riveter as this will cause damage to the riveter and mandrel.

Text in Illustration
*1 Riveter
*2 Mandrel
*a Incorrect
*b Correct

·
B172390E42
0.719,0.115 1.021,0.115 false 0.813,1.156 1.01,1.156 false 0.813,2.427 1.01,2.427 false 2.323,0.552 2.51,0.729 0.188,0.177 10 false *a 2.323,1.563 2.5,1.74 0.177,0.177 10 false *a 2.427,2.781 2.625,2.958 0.198,0.177 10 false *b 1.042,2.333 1.219,2.49 0.177,0.156 10 false *1 1.042,1.083 1.219,1.24 0.177,0.156 10 false *1 1.042,0.031 1.219,0.188 0.177,0.156 10 false *1

Confirm that the rivets are seated properly against the front door glass inner weatherstrip.

Text in Illustration
*1 Riveter
*a Incorrect
*b Correct

·

Do not tilt the riveter when installing the rivet to the front door glass inner weatherstrip

·

Do not leave any space between the rivet head and front door glass inner weatherstrip.




d.
B373209E02
1.031,0.917 0.708,0.635 false 2.229,0.49 2.698,0.271 false 2.115,1.104 2.823,0.781 false 2.344,1.219 2.802,1.469 false 1.958,1.26 1.563,1.406 false 2.719,0.177 2.885,0.344 0.167,0.167 10 false *1 1.354,1.354 1.521,1.521 0.167,0.167 10 false *3 2.875,0.646 3.042,0.813 0.167,0.167 10 false *4 0.49,0.51 0.656,0.677 0.167,0.167 10 false *2 2.833,1.396 3,1.563 0.167,0.167 10 false *5

After installing the rivet, cut nonwoven tape into a 15 mm (0.591 in.) x 15 mm (0.591 in.) square and attach it to the crimped section of the rivet.

Text in Illustration
*1 Front Door Glass Sub-assembly
*2 Front Door Trim Board Sub-assembly
*3 Nonwoven Tape
*4 Rivet
*5 Front Door Glass Inner Weatherstrip

NOTICE:
·

The crimp height of the rivet must be 3 mm (0.118 in.).

·

If the crimp is not firm enough, flatten it using pliers or the like to avoid interference with the door panel.




e.

After installing the front door glass inner weatherstrip, check the following items:

·

Check that there is no gap between the front door glass inner weatherstrip and the front door trim board sub-assembly.

·

Pull the front door glass inner weatherstrip lightly and check that there is no play.



Hide 67736 30.INSTALL FRONT LOWER DOOR TRIM PAD

a.
B314157

Install the front lower door trim pad with the 5 screws.


Hide 74640C 31.INSTALL DOOR ASSIST GRIP ASSEMBLY

a.
B314156

Engage the guide and install the door assist grip assembly with the 2 screws.


Hide 32.INSTALL POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)

a.
B314154

Install the power window regulator master switch assembly with front door armrest base panel with the 4 screws.


Hide 33.INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)

a.
B314155

Install the power window regulator switch assembly with front door armrest base panel with the 4 screws.


Hide 69206B 34.INSTALL FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY

a.
B314153

Engage the 2 guides.


b.

Install the front door inside handle sub-assembly to the front door trim board sub-assembly with the 2 screws.


Hide 67602 35.INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY

a.
B313122E01
2.408,0.084 2.562,0.234 0.154,0.150 10 *1 0.19,1.791 0.345,1.941 0.154,0.150 10 *2 0.962,0.644 2.358,0.223 false 0.811,1.338 0.357,1.767 false

Connect the front door lock remote control cable assembly and front door inside locking cable assembly to the front door inside handle.

Text in Illustration
*1 Front Door Inside Locking Cable Assembly
*2 Front Door Lock Remote Control Cable Assembly


b.

Connect each connector.


c.
B314824

Engage the 10 clips and install the front door trim board sub-assembly.


d.
B313120

Engage the clip and install the 3 screws.


e.
B314825

Engage the claw and install the cap.


Hide 81230 36.INSTALL COURTESY LIGHT ASSEMBLY (w/ Courtesy Light)

Hide 74222 37.INSTALL DOOR ARMREST COVER

a.
B314960

Engage the guide and 7 claws, and install the door armrest cover.


Hide 38.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)

Hide 39.INITIALIZE POWER WINDOW CONTROL SYSTEM