Home › Drivetrain › AXLE AND DIFFERENTIAL › FRONT AXLE HUB BOLT › from 2017.03
RM2090E _52 Drivetrain _060678 AXLE AND DIFFERENTIAL _0297584 FRONT AXLE HUB BOLT A

AXLE AND DIFFERENTIAL  FRONT AXLE HUB BOLT  REPLACEMENT  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1.REMOVE FRONT WHEEL

Hide 47710A 2.SEPARATE FRONT DISC BRAKE CALIPER ASSEMBLY

a.

for floating type caliper

i.

Remove the 2 bolts and separate the front disc brake caliper assembly from the steering knuckle.

NOTICE:

Hang the front disc brake caliper assembly using a piece of string or equivalent.




b.

for opposed type caliper

i.

Remove the 2 bolts and front disc brake cylinder mounting, and then separate the front disc brake cylinder assembly from the steering knuckle.

NOTICE:

Hang the front disc brake cylinder assembly using a piece of string or equivalent.




Hide 43512 3.REMOVE FRONT DISC

Hide 43502D 4.REMOVE FRONT AXLE HUB BOLT

a.

Using SST, remove the front axle hub bolt from the front axle hub sub-assembly.

C265372C02
0.958,0.438 1.167,0.438 false 1.198,3.198 1.406,3.198 1.406,3.198 1.896,2.938 false 5.99,1.875 5.771,1.875 5.771,1.875 5.771,2.469 false 6.313,2.104 6.104,2.104 6.104,2.104 6.104,2.427 false 6.771,3.188 6.771,2.833 6.771,2.833 6.542,2.833 false 6.771,2.917 6.542,2.917 false 5.396,3.292 5.604,3.292 5.604,3.292 5.604,3.063 false 1.177,0.333 1.365,0.521 0.188,0.188 10 false *a 0.896,3.125 1.26,3.313 0.365,0.188 10 false SST 6.021,1.781 6.208,1.969 0.188,0.188 10 false *3 6.333,2 6.521,2.188 0.188,0.188 10 false *1 6.698,3.188 6.885,3.375 0.188,0.188 10 false *4 5.219,3.208 5.406,3.396 0.188,0.188 10 false *2
*1 Nut *2 Body
*3 Claw *4 SST (Spacer B)
*a Place a Wrench Here - -
V100135

Molybdenum Grease
V100136

Turn


SST
09960-20010  (09961-02010, 09961-02060)

CAUTION:

Before working, apply molybdenum grease to the bolt threads and bolt tip of SST.


NOTICE:
·

Install SST so that claw and body are parallel.

·

Make sure to tie the string of SST to the vehicle to prevent SST from dropping.

·

Do not damage the front disc brake dust cover.

·

Do not damage the front axle hub.

·

Do not damage the steering knuckle.




Hide 43502D 5.INSTALL FRONT AXLE HUB BOLT

a.
C257542C03
2.729,0.427 3.167,0.25 true 3.01,0.885 3.01,1.229 true 1.5,0.813 1.594,0.24 true 2.74,1.573 2.896,1.719 0.156,0.146 10 false *a 2.917,1.24 3.073,1.385 0.156,0.146 10 false *1 0.604,1.698 0.76,1.844 0.156,0.146 10 false *b 1.5,0.052 1.656,0.198 0.156,0.146 10 false *1 3.208,0.104 3.365,0.25 0.156,0.146 10 false *2
*1 Nut
*2 Washer
*3 Turn
*4 Hold


Set a new axle hub bolt onto the front axle hub, and tighten the nut (M12 x P1.25mm (0.0492 in.)) through the washer plate to install the axle hub bolt.

NOTICE:

Install the nuts to prevent damage to the front axle hub bolts.



Hide 43512 6.INSTALL FRONT DISC

Hide 47710A 7.INSTALL FRONT DISC BRAKE CALIPER ASSEMBLY

a.

for floating type caliper

i.

Install the front disc brake caliper assembly to the steering knuckle with 2 new bolts.

Torque:
Bolt Type A : 80 N*m (816 kgf*cm, 59 ft.*lbf)
Bolt Type B : 135 N*m (1377 kgf*cm, 100 ft.*lbf)

HINT:
C398290C01
0.219,0.135 0.531,0.333 0.313,0.198 10 false *A 0.208,1.365 0.521,1.563 0.313,0.198 10 false *B 0.813,0.448 1.125,0.646 0.313,0.198 10 false *a 0.802,1.552 1.115,1.75 0.313,0.198 10 false *a

Bolt type A and bolt type B can be distinguished by the sizes of the mounting bolts.

Bolt Type Width Across Flats
A 17 mm (0.669 in.)
B 19 mm (0.748 in.)

Text in Illustration
*A Bolt Type A
*B Bolt Type B
*a Width Across Flats




b.
C377914C03
1.427,0.208 1.74,0.365 0.313,0.156 10 false *a
*a Torque Wrench Fulcrum Length


for opposed type caliper

i.

Install the front disc brake cylinder assembly and front disc brake cylinder mounting with the 2 bolts.

NOTICE:

When installing the front disc brake cylinder assembly and front disc brake cylinder mounting, hand-tighten the 2 bolts temporarily until they cannot be turned further, and tighten them to the specified torque.


Torque:
120 N*m (1224 kgf*cm, 89 ft.*lbf)

HINT:
·

When tightening the upper bolt, use a union nut wrench.

·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 400 mm (15.7 in.)): 111.6 N*m (1138 kgf*cm, 82 ft.*lbf)





Hide 8.INSTALL FRONT WHEEL

Torque:
120 N*m (1224 kgf*cm, 89 ft.*lbf)