Home › Engine / Hybrid System › K3-VE ENGINE CONTROL › SFI SYSTEM › 2011.11–2015.08
RM19Y0E _51 Engine / Hybrid System _002967 K3-VE ENGINE CONTROL _0014971 SFI SYSTEM J

K3-VE ENGINE CONTROL  SFI SYSTEM  Fuel Pump Control Circuit  


DESCRIPTION

When the engine is cranked, a current flows from terminal ST of the ignition switch to terminal STA of the ECM (STA signal).

When signals STA, N and N2 are input to the ECM, transistor (Tr) turns ON, a current flows to the coil of the F/P (fuel pump) relay, the relay switch turns ON, and a current flows to the fuel pump. The fuel pump is then actuated.

While the N and N2 signals are generated (engine running), the ECM keeps Tr ON (fuel pump relay ON) and the fuel pump also keeps operating.

A263582E07
0.698,6.646 1.896,7.094 1.198,0.448 10 BATTERY 2.938,6.26 3.865,6.781 0.927,0.521 10 STARTER 0.521,4.99 1.385,5.365 0.865,0.375 10 FL MAIN 0.521,2.417 1.083,2.823 0.563,0.406 10 AM2 1.156,2.417 1.688,2.844 0.531,0.427 10 EFI 1.438,1.469 2.052,1.917 0.615,0.448 10 AM2 1.979,1.125 2.531,1.49 0.552,0.365 10 IG2 2.021,1.406 2.521,1.729 0.5,0.323 10 ST 2.531,1.333 3.042,1.802 0.51,0.469 10 E/G 1.24,1.917 2.635,2.344 1.396,0.427 10 IGNITION SWITCH 3.375,1.542 4.292,1.979 0.917,0.438 10 EFI MAIN 4.781,1.552 5.229,1.969 0.448,0.417 10 F/P 5.5,0.896 6.521,1.375 1.021,0.479 10 FUEL PUMP 6.208,5.833 6.75,6.26 0.542,0.427 10 ECM 5.688,2.156 6.385,2.594 0.698,0.438 10 FC1 *1 5.677,3.802 6.177,4.24 0.5,0.438 10 STA 4.031,4.052 4.604,4.49 0.573,0.438 10 ST 5.677,5.177 6.563,5.604 0.885,0.427 10 N and N2 3.5,5.26 5,5.802 1.5,0.542 10 (N and N2 Signal) 6.375,2.333 6.792,2.781 0.417,0.448 10 Tr 5.229,0.583 5.583,0.906 0.354,0.323 10 5 5.229,1.115 5.5,1.479 0.271,0.365 10 1 4.479,0.594 4.76,0.917 0.281,0.323 10 3 4.479,1.125 4.792,1.542 0.313,0.417 10 2 4.01,0.594 4.26,0.885 0.25,0.292 10 5 4.01,1.125 4.333,1.479 0.323,0.354 10 1 3.26,0.604 3.583,0.854 0.323,0.25 10 3 3.26,1.125 3.646,1.5 0.385,0.375 10 2 2.292,1.125 2.771,1.521 0.479,0.396 10 6 2.292,1.406 2.698,1.823 0.406,0.417 10 4 1.281,1.25 1.646,1.573 0.365,0.323 10 5 5.688,2.313 6.365,2.698 0.677,0.385 10 FC2 *2 3.969,6.979 6.865,7.458 2.896,0.479 10 *1: w/o Engine Immobiliser System 3.969,7.354 6.885,7.854 2.917,0.5 10 *2: w/ Engine Immobiliser System

WIRING DIAGRAM

A268113E03
0.781,6.479 1.823,6.875 1.042,0.396 10 BATTERY 0.615,4.958 1.531,5.427 0.917,0.469 10 FL MAIN 1.375,3.26 2.146,3.667 0.771,0.406 10 EFI 0.615,2.198 1.281,2.594 0.667,0.396 10 AM2 0.833,0.698 1.365,1.073 0.531,0.375 10 AM2 1.51,0.698 2.104,1.135 0.594,0.438 10 IG2 0.823,1.188 1.438,1.542 0.615,0.354 10 E28 0.823,1.344 1.969,1.792 1.146,0.448 10 Ignition Switch 2.146,1.823 2.958,2.292 0.813,0.469 10 E/G 2.75,4.948 3.563,5.344 0.813,0.396 10 EFI MAIN 5.729,5.427 6.583,5.865 0.854,0.438 10 Fuel Pump 5.875,1.885 6.417,2.229 0.542,0.344 10 E01 5.521,1.875 6.063,2.333 0.542,0.458 10 C24 5.615,1.698 5.958,2.073 0.344,0.375 10 7 5.885,1.302 6.385,1.646 0.5,0.344 10 FC1 5.563,1.292 5.917,1.635 0.354,0.344 10 E3 5.563,1.104 5.969,1.448 0.406,0.344 10 18 6.188,2.333 6.844,2.677 0.656,0.344 10 ECM 0.667,0.698 1.094,1.135 0.427,0.438 10 5 1.833,0.698 2.219,1.042 0.385,0.344 10 6 1.938,4.563 2.198,4.896 0.26,0.333 10 2 1.938,5.354 2.333,5.74 0.396,0.385 10 1 2.365,4.563 2.719,4.885 0.354,0.323 10 3 2.365,5.354 2.76,5.646 0.396,0.292 10 5 3.552,4.563 3.99,4.948 0.438,0.385 10 2 3.552,5.354 3.781,5.667 0.229,0.313 10 1 3.99,4.563 4.354,4.833 0.365,0.271 10 5 3.99,5.354 4.344,5.698 0.354,0.344 10 3 4.344,4.969 4.76,5.375 0.417,0.406 10 F/P 5.354,4.792 5.625,5.063 0.271,0.271 10 4 5.729,5.219 6.188,5.552 0.458,0.333 10 P1 5.354,5.802 5.635,6.104 0.281,0.302 10 5 5.396,4.969 5.688,5.24 0.292,0.271 10 + 5.406,5.583 5.75,5.865 0.344,0.281 10 E 5.875,0.677 6.396,1.01 0.521,0.333 10 FC2 5.573,0.677 6.01,1.052 0.438,0.375 10 E3 5.573,0.49 5.927,0.833 0.354,0.344 10 17 5.073,1.406 5.448,1.76 0.375,0.354 10 *1 5.073,0.781 5.396,1.115 0.323,0.333 10 *2 0.115,7.26 2.969,7.677 2.854,0.417 10 *1: w/o Engine Immobilizer System 0.115,7.542 3.073,7.854 2.958,0.313 10 *2: w/ Engine Immobilizer System

PROCEDURE

1.CHECK OPERATION OF FUEL PUMP
a.
A261189C01
0.948,0.354 0.458,0.198 true 0.24,0.094 0.698,0.5 0.458,0.406 10 *1
*1 Screw


Start the engine (engine cranking operation).


b.

Check that the fuel pulsation damper extrudes its screw.

Standard:

Fuel pulsation damper extrudes its screw.


HINT:
·

After the engine starts, check that the fuel pump operating sound occurs.

·

The fuel pump can be operated without the engine running.

Click hereEngine / Hybrid System>K3-VE FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION



Result:
Proceed to
OK
NG




OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN ON PROBLEM SYMPTOMS TABLE

NG

2.INSPECT ECM (+B1 VOLTAGE)
2.INSPECT ECM (+B1 VOLTAGE)

OK

3.INSPECT FUEL PUMP RELAY (F/P RELAY)

NG

3.INSPECT FUEL PUMP RELAY (F/P RELAY)
a.
A167865N12
2.01,0.594 1.552,0.24 true 2.656,0.625 3.063,0.25 true 2.531,1.125 3.063,1.125 true 2.531,1.625 3.073,1.625 true 1.208,0.76 1.542,1.083 0.333,0.323 10 5 0.208,0.771 0.615,1.198 0.406,0.427 10 3 1.229,1.313 1.594,1.708 0.365,0.396 10 2 0.208,1.292 0.563,1.594 0.354,0.302 10 1 1.417,0.125 1.792,0.458 0.375,0.333 10 1 3.125,0.135 3.427,0.438 0.302,0.302 10 2 3.125,1.552 3.427,1.823 0.302,0.271 10 3 3.125,1.042 3.427,1.333 0.302,0.292 10 5

Remove the F/P relay from the fuse block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 No battery voltage applied to terminals 1 and 2 10 kΩ or higher
3 - 5 Battery voltage applied to terminals 1 and 2 Below 1 Ω



c.

Reinstall the F/P relay.

Result:
Proceed to
OK
NG




OK

4.INSPECT ECM (FC VOLTAGE)

NG

REPLACE FUEL PUMP RELAY

4.INSPECT ECM (FC VOLTAGE)
a.
A141531C23
1.479,1.01 1.854,1.208 0.375,0.198 2.313,1.021 2.688,1.219 0.375,0.198 1.052,2.552 1.375,1.552 true 2.927,2.573 2.833,1.719 true 2.406,2.719 2.771,1.729 true 0.917,2.594 1.563,3.01 0.646,0.417 10 E01 2.781,2.604 3.24,3.021 0.458,0.417 10 FC2 0.188,0.167 1.052,0.74 0.865,0.573 10 *a 1.542,1.031 2.167,1.406 0.625,0.375 10 C24 2.406,1.031 2.958,1.427 0.552,0.396 10 E3 2.25,2.792 2.896,3.208 0.646,0.417 10 FC1
*a Component with harness connected
(ECM)


Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage (w/o Engine Immobilizer System):
Tester Connection Switch Condition Specified Condition
E3-18 (FC1) - C24-7 (E01) Ignition switch ON 11 to 14 V


Standard Voltage (w/ Engine Immobilizer System):
Tester Connection Switch Condition Specified Condition
E3-17 (FC2) - C24-7 (E01) Ignition switch ON 11 to 14 V


HINT:

The fuel pump operates for 2 seconds after the ignition switch has been turned to ON. If the ignition switch was turned to ON with EFIT and E terminals of DLC3 connected, the fuel pump operates for 8 seconds. The voltage between FC and E01 decreases to below 2 V in both cases.


Result:
Proceed to
OK
NG




OK

5.INSPECT FUEL PUMP

NG

9.CHECK HARNESS AND CONNECTOR (ECM - F/P RELAY)
5.INSPECT FUEL PUMP
a.

Inspect the fuel pump.

Click hereEngine / Hybrid System>K3-VE FUEL>FUEL PUMP>INSPECTION

Result:
Proceed to
OK
NG




OK

6.CHECK HARNESS AND CONNECTOR (F/P RELAY - FUEL PUMP)

NG

6.CHECK HARNESS AND CONNECTOR (F/P RELAY - FUEL PUMP)
a.

Remove the F/P relay from the fuse block.


b.

Disconnect the fuel pump connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
F/P relay (5) - P1-4 (+) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
F/P relay (5) or P1-4 (+) - Body ground Always 10 kΩ or higher



d.

Reconnect the fuel pump connector.


e.

Reinstall the F/P relay.

Result:
Proceed to
OK
NG




OK

7.CHECK HARNESS AND CONNECTOR (FUEL PUMP - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (FUEL PUMP - BODY GROUND)
a.

Disconnect the fuel pump connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
P1-5 (E) - Body ground Always Below 1 Ω



c.

Reconnect the fuel pump connector.

Result:
Proceed to
OK
NG




OK

8.CHECK HARNESS AND CONNECTOR (F/P RELAY - EFI MAIN RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (F/P RELAY - EFI MAIN RELAY)
a.

Remove the F/P relay from the fuse block.


b.

Remove the EFI MAIN relay from the fuse block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
F/P relay (3) - EFI MAIN relay (5) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
F/P relay (3) or EFI MAIN relay (5) - Body ground Always 10 kΩ or higher



d.

Reinstall the EFI MAIN relay.


e.

Reinstall the F/P relay.

Result:
Result Proceed to
NG A
OK (for LHD) B
OK (for RHD) C




A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

C

9.CHECK HARNESS AND CONNECTOR (ECM - F/P RELAY)
a.

Disconnect the ECM connector.


b.

Remove the F/P relay from the fuse block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open) (w/o Engine Immobilizer System):
Tester Connection Condition Specified Condition
E3-18 (FC1) - F/P relay (1) Always Below 1 Ω


Standard Resistance (Check for Open) (w/ Engine Immobilizer System):
Tester Connection Condition Specified Condition
E3-17 (FC2) - F/P relay (1) Always Below 1 Ω


Standard Resistance (Check for Short) (w/o Engine Immobilizer System):
Tester Connection Condition Specified Condition
E3-18 (FC1) or F/P relay (1) - Body ground Always 10 kΩ or higher


Standard Resistance (Check for Short) (w/ Engine Immobilizer System):
Tester Connection Condition Specified Condition
E3-17 (FC2) or F/P relay (1) - Body ground Always 10 kΩ or higher



d.

Reconnect the ECM connector


e.

Reinstall the F/P relay.

Result:
Proceed to
OK
NG




OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION SWITCH - F/P RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR