The Crankshaft Position (CKP) sensor system consists of a CKP sensor plate and a pickup coil. The sensor plate has 30 teeth and is installed on the crankshaft. The pickup coil is made of wound copper wire, an iron core and magnet.
The sensor plate rotates and, as each tooth passes through the pickup coil, a pulse signal is created. The pickup coil generates 30 signals per engine revolution. Based on these signals, the ECM calculates the crankshaft position and engine RPM. Using these calculations, the fuel injection time and ignition timing are controlled.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0335 | Crankshaft Position Sensor "A" Circuit | No crankshaft position sensor signal to ECM for 2 seconds or more during starter ON
(1 trip detection logic) |
·
Open or short in crankshaft position sensor circuit ·
Crankshaft position sensor ·
No.1 crankshaft position sensor plate ·
ECM |
Comes on | DTC stored |
If no problem is found through this diagnostic troubleshooting procedure, troubleshoot the engine mechanical system.
Check the engine speed. The engine speed can be checked by using an intelligent tester. To check, follow the operation below:
Connect the intelligent tester to the DLC3.
Start the engine.
Turn the tester on.
Enter the following menus: Powertrain / Engine / Data List / Engine Speed.
The engine speed may be indicated as zero despite the engine revolving normally. This is caused by a lack of NE signals from the Crankshaft Position (CKP) sensor. Alternatively, the engine speed may be indicated as lower than the actual engine speed, if the CKP sensor output voltage is insufficient.
Read freeze frame data using an intelligent tester. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data, from the time the malfunction occurred.
| Tester Display |
|---|
| Engine Speed |
| *a | Component with harness connected
(ECM) |
Connect the oscilloscope probes to the N+ terminal and N- terminal of the ECM connector.
Check the waveform when the engine is idling or cranking.
| Terminal No. (Symbol) | Tool Setting | Condition |
|---|---|---|
| C24-9 (N+) - C24-29 (N-) | 2 V/DIV, 20 msec./DIV | Idling |
The waveform exists in accordance with the engine speed.
The waveforms shown in the illustration are at engine idling speed.
The oscilloscope waveform shown as an example does not include noise or chattering waveforms.
The waveform amplitudes differ slightly depending on the vehicle conditions.
Failure grounding of the shielded wire may cause noise in waveforms.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the crankshaft position sensor.
Click hereEngine / Hybrid System>K3-VE ENGINE CONTROL>CRANKSHAFT POSITION SENSOR>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the crankshaft position sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C10-1 - C24-9 (N+) | Always | Below 1 Ω |
| C10-2 - C24-29 (N-) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C10-1 or C24-9 (N+) - Body ground | Always | 10 kΩ or higher |
| C10-2 or C24-29 (N-) - Body ground | Always | 10 kΩ or higher |
Reconnect the ECM connector.
Reconnect the crankshaft position sensor connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the crankshaft position sensor installation.
Sensor is installed correctly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the teeth of the sensor plate.
Sensor plate does not have any cracks or deformation.
| Result | Proceed to |
|---|---|
| NG | A |
| OK (for LHD) | B |
| OK (for RHD) | C |
A
B
C