Home › Engine / Hybrid System › 3SZ-VE ENGINE CONTROL › SFI SYSTEM(w/ Rear Heated Oxygen Sensor) › 2011.11–2015.08
RM19Y0E _51 Engine / Hybrid System _002968 3SZ-VE ENGINE CONTROL _0014988 SFI SYSTEM(w/ Rear Heated Oxygen Sensor) C

3SZ-VE ENGINE CONTROL  SFI SYSTEM(w/ Rear Heated Oxygen Sensor)  P0300  Random / Multiple Cylinder Misfire Detected  P0301  Cylinder 1 Misfire Detected  P0302  Cylinder 2 Misfire Detected  P0303  Cylinder 3 Misfire Detected  P0304  Cylinder 4 Misfire Detected  


DESCRIPTION

When the engine misfires, high concentrations of hydrocarbons (HC) enter the exhaust gas. Extremely high hydrocarbon concentration levels can cause an increase in exhaust emission levels. Extremely high concentrations of hydrocarbons can also cause increases in the three-way catalytic converter temperature, which may cause damage to the three-way catalytic converter. To prevent this increase in emissions and to limit the possibility of thermal damage, the ECM monitors the misfire count. When the temperature of the three-way catalytic converter reaches the point of thermal degradation, the ECM blinks the MIL. To monitor misfires, the ECM uses both the camshaft position sensor and the crankshaft position sensor. The camshaft position sensor is used to identify any misfiring cylinders and the crankshaft position sensor is used to measure variations in the crankshaft rotation speed. Misfires are counted when the crankshaft rotation speed variations exceed predetermined thresholds. If the misfire count exceeds the threshold levels, and could cause emission control system performance deterioration, the ECM illuminates the MIL and sets a DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0300 Random / Multiple Cylinder Misfire Detected Simultaneous misfiring of several cylinders detected
(2 trip detection logic)
·

Open or short in engine wire harness

·

Connector connection

·

PCV valve and ventilation hose

·

Ventilation hose connections

·

Ignition system

·

Injector

·

Fuel pressure

·

Manifold absolute pressure sensor

·

Engine Coolant Temperature (ECT) sensor

·

Compression pressure

·

Valve clearance

·

Valve timing

·

ECM


Comes on/Blinks* DTC stored
P0301 Cylinder 1 Misfire Detected Misfiring of specific cylinder detected
(2 trip detection logic)
·

Open or short in engine wire harness

·

Connector connection

·

PCV valve and ventilation hose

·

Ventilation hose connections

·

Ignition system

·

Injector

·

Fuel pressure

·

Manifold absolute pressure sensor

·

Engine Coolant Temperature (ECT) sensor

·

Compression pressure

·

Valve clearance

·

Valve timing

·

ECM


Comes on/Blinks* DTC stored
P0302 Cylinder 2 Misfire Detected Misfiring of specific cylinder detected
(2 trip detection logic)
·

Open or short in engine wire harness

·

Connector connection

·

PCV valve and ventilation hose

·

Ventilation hose connections

·

Ignition system

·

Injector

·

Fuel pressure

·

Manifold absolute pressure sensor

·

Engine Coolant Temperature (ECT) sensor

·

Compression pressure

·

Valve clearance

·

Valve timing

·

ECM


Comes on/Blinks* DTC stored
P0303 Cylinder 3 Misfire Detected Misfiring of specific cylinder detected
(2 trip detection logic)
·

Open or short in engine wire harness

·

Connector connection

·

PCV valve and ventilation hose

·

Ventilation hose connections

·

Ignition system

·

Injector

·

Fuel pressure

·

Manifold absolute pressure sensor

·

Engine Coolant Temperature (ECT) sensor

·

Compression pressure

·

Valve clearance

·

Valve timing

·

ECM


Comes on/Blinks* DTC stored
P0304 Cylinder 4 Misfire Detected Misfiring of specific cylinder detected
(2 trip detection logic)
·

Open or short in engine wire harness

·

Connector connection

·

PCV valve and ventilation hose

·

Ventilation hose connections

·

Ignition system

·

Injector

·

Fuel pressure

·

Manifold absolute pressure sensor

·

Engine Coolant Temperature (ECT) sensor

·

Compression pressure

·

Valve clearance

·

Valve timing

·

ECM


Comes on/Blinks* DTC stored

When DTCs for misfiring cylinders are randomly set, but DTC P0300 is not set, it indicates that misfires have been detected in different cylinders at different times. DTC P0300 is only set when several misfiring cylinders are detected at the same time.

WIRING DIAGRAM

Wiring diagram of the ignition system.

A262620E05
3.99,3.583 4.333,3.896 0.344,0.313 10 3 3.99,4.865 4.313,5.198 0.323,0.333 10 3 3.99,6.125 4.281,6.448 0.292,0.323 10 3 1.438,0.865 1.917,1.167 0.479,0.302 10 E28 1.438,1.021 2.875,1.406 1.438,0.385 10 IGNITION SWITCH 1.573,0.469 2.052,0.792 0.479,0.323 10 AM2 2.354,0.469 2.771,0.792 0.417,0.323 10 IG2 1.406,0.469 1.74,0.833 0.333,0.365 10 5 2.677,0.469 3.073,0.875 0.396,0.406 10 6 3.729,0.698 4.229,1.073 0.5,0.375 10 E/G 2.677,2.5 3.073,2.833 0.396,0.333 10 4 3.99,2.344 4.26,2.667 0.271,0.323 10 3 2.25,2.885 2.698,3.219 0.448,0.333 10 C1 2.25,3.042 4.458,3.417 2.208,0.375 10 NO. 1 IGNITION COIL ASSEMBLY 2.677,3.458 3,3.771 0.323,0.313 10 1 2.677,2.198 3.01,2.531 0.333,0.333 10 1 2.677,3.74 3,4.031 0.323,0.292 10 4 2.25,4.146 2.521,4.302 0.271,0.156 10 C2 2.25,4.292 4.615,4.656 2.365,0.365 10 NO. 2 IGNITION COIL ASSEMBLY 2.677,4.719 2.99,5.063 0.313,0.344 10 1 2.677,5.021 2.99,5.375 0.313,0.354 10 4 2.25,5.417 2.667,5.667 0.417,0.25 10 C3 2.25,5.573 4.729,5.885 2.479,0.313 10 NO. 3 IGNITION COIL ASSEMBLY 2.677,5.979 2.958,6.313 0.281,0.333 10 1 2.677,6.281 2.99,6.594 0.313,0.313 10 4 2.25,6.677 2.792,7.031 0.542,0.354 10 C4 2.25,6.833 4.49,7.167 2.24,0.333 10 NO. 4 IGNITION COIL ASSEMBLY 0.417,3.156 1.021,3.563 0.604,0.406 10 AM2 0.417,5.375 1.313,5.896 0.896,0.521 10 FL MAIN 0.604,7.802 1.563,8.271 0.958,0.469 10 BATTERY 5.99,7.823 6.552,8.219 0.563,0.396 10 ECM 4.99,2.448 5.479,2.833 0.49,0.385 10 C23 5.333,2.333 5.729,2.688 0.396,0.354 10 IG1 5.333,3.594 5.813,3.927 0.479,0.333 10 IG2 5.323,4.854 5.771,5.229 0.448,0.375 10 IG3 5.333,6.125 5.719,6.458 0.385,0.333 10 IG4 5.333,6.927 5.771,7.281 0.438,0.354 10 E1 5.042,2.26 5.427,2.615 0.385,0.354 10 12 4.99,3.698 5.5,4.063 0.51,0.365 10 C23 5.042,3.521 5.438,3.875 0.396,0.354 10 11 4.99,4.979 5.49,5.333 0.5,0.354 10 C23 5.042,4.792 5.365,5.094 0.323,0.302 10 10 4.99,6.229 5.552,6.646 0.563,0.417 10 C23 5.083,6.042 5.427,6.396 0.344,0.354 10 9 4.99,6.938 5.51,7.333 0.521,0.396 10 C24 5.042,6.75 5.354,7 0.313,0.25 10 32 2.885,2.292 3.198,2.583 0.313,0.292 10 + 2.896,2.583 3.156,2.833 0.26,0.25 10 - 3.625,2.438 3.896,2.865 0.271,0.427 10 IGT 2.875,3.542 3.188,3.771 0.313,0.229 10 + 2.896,3.844 3.188,4.083 0.292,0.24 10 - 3.615,3.698 3.885,4.125 0.271,0.427 10 IGT 2.875,4.823 3.198,5.094 0.323,0.271 10 + 2.896,5.104 3.146,5.344 0.25,0.24 10 - 3.615,4.979 4.031,5.417 0.417,0.438 10 IGT 2.865,6.083 3.177,6.458 0.313,0.375 10 + 2.906,6.375 3.198,6.667 0.292,0.292 10 - 3.615,6.24 3.948,6.698 0.333,0.458 10 IGT

Wiring diagram of the injector circuit.

A262621E03
0.573,6.542 1.427,6.823 0.854,0.281 10 BATTERY 0.417,4.969 1.156,5.302 0.74,0.333 10 FL MAIN 0.406,2.177 0.958,2.542 0.552,0.365 10 AM2 1.896,2.156 2.344,2.479 0.448,0.323 10 EFI 2.438,1.646 3.156,1.906 0.719,0.26 10 EFI MAIN 1.896,1.063 2.323,1.344 0.427,0.281 10 E/G 0.615,0.813 1.146,1.115 0.531,0.302 10 AM2 1.344,0.813 1.781,1.135 0.438,0.323 10 IG2 0.5,1.281 0.979,1.625 0.479,0.344 10 E28 0.5,1.438 1.865,1.781 1.365,0.344 10 IGNITION SWITCH 5.469,1.313 5.969,1.729 0.5,0.417 10 C23 5.542,1.125 5.844,1.448 0.302,0.323 10 4 5.813,1.208 6.313,1.563 0.5,0.354 10 #10 5.469,2.594 5.917,2.958 0.448,0.365 10 C23 5.542,2.396 5.854,2.719 0.313,0.323 10 3 5.813,2.49 6.25,2.823 0.438,0.333 10 #20 5.469,3.896 6,4.281 0.531,0.385 10 C23 5.542,3.708 5.854,4.042 0.313,0.333 10 2 5.813,3.792 6.24,4.135 0.427,0.344 10 #30 5.469,5.188 5.875,5.49 0.406,0.302 10 C23 5.542,4.99 5.865,5.302 0.323,0.313 10 1 5.813,5.083 6.25,5.406 0.438,0.323 10 #40 5.469,6.479 5.854,6.76 0.385,0.281 10 C24 5.542,6.281 5.833,6.583 0.292,0.302 10 7 5.813,6.375 6.24,6.708 0.427,0.333 10 E01 6.24,7.104 6.677,7.427 0.438,0.323 10 ECM 3.708,1.594 4.135,1.906 0.427,0.313 10 C5 3.708,1.74 5.229,2.104 1.521,0.365 10 NO. 1 FUEL INJECTOR ASSEMBLY 3.708,2.875 4.042,3.042 0.333,0.167 10 C6 3.708,3.021 5.26,3.375 1.552,0.354 10 NO. 2 FUEL INJECTOR ASSEMBLY 3.708,4.188 4.104,4.5 0.396,0.313 10 C7 3.708,4.333 5.25,4.708 1.542,0.375 10 NO. 3 FUEL INJECTOR ASSEMBLY 3.708,5.479 4.198,5.781 0.49,0.302 10 C8 3.708,5.625 5.281,5.979 1.573,0.354 10 NO. 4 FUEL INJECTOR ASSEMBLY 0.438,0.813 0.771,1.146 0.333,0.333 10 5 1.656,0.813 1.958,1.156 0.302,0.344 10 6 2.323,0.802 2.635,1.125 0.313,0.323 10 2 3.083,0.802 3.438,1.167 0.354,0.365 10 1 2.323,1.208 2.719,1.594 0.396,0.385 10 3 3.083,1.208 3.385,1.51 0.302,0.302 10 5 4.76,1.198 5.094,1.531 0.333,0.333 10 2 4.01,1.198 4.354,1.49 0.344,0.292 10 1 4.76,2.5 5.021,2.854 0.26,0.354 10 2 4.01,2.5 4.344,2.875 0.333,0.375 10 1 4.76,3.802 5.063,4.094 0.302,0.292 10 2 4.01,3.802 4.292,4.094 0.281,0.292 10 1 4.76,5.094 5.01,5.375 0.25,0.281 10 2 4.01,5.094 4.323,5.427 0.313,0.333 10 1

CONFIRMATION DRIVING PATTERN

1.

Connect the intelligent tester or Techstream to the DLC3.

2.

Turn the ignition switch to ON and turn the intelligent tester or Techstream on.

3.

Record the DTC(s) and freeze frame data.

4.

Drive the vehicle several times with the conditions when malfunctions are detected.

HINT:

In order to store misfire DTCs, it is necessary to drive the vehicle for the period of time shown in the table below.

Engine RPM Duration
Idling 7 minutes or more
1000 4 minutes or more
2000 2.0 minutes or more
3000 1.5 minute or more


5.

Check whether misfires have occurred by checking DTCs and freeze frame data.

HINT:

Do not turn the ignition switch off until the stored DTC(s) and freeze frame data have been recorded. The stored DTC(s), freeze frame data and other data will be erased.


6.

Record the DTC(s), freeze frame data.

7.

Turn the ignition switch off and wait for at least 30 seconds.


Powertrain > Engine > Trouble Codes
50001 206

CAUTION / NOTICE / HINT

HINT:
·

If any DTCs other than misfire DTCs are output, troubleshoot those DTCs first.

·

Read freeze frame data using the intelligent tester or Techstream. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data, from the time the malfunction occurred.

·

If the misfire does not recur when the vehicle is brought to the workshop, reproduce the conditions stored in the freeze frame data.

·

If the misfire still cannot be reproduced even though the conditions stored in the freeze frame data have been duplicated, one of the following factors is considered to be a possible cause of the problem:

1.

The fuel level is low.

2.

Improper fuel is used.

3.

The spark plugs are dirty.

4.

The problem is complex due to multiple factors.


·

After finishing repairs, check that no misfire occur in each cylinder (Cylinder #1, #2, #3 and #4).

·

Be sure to confirm that no misfiring cylinder DTCs are set again by conducting the confirmation driving pattern, after the repairs.

·

When either Short FT #1 or Long FT #1 in the freeze frame data is outside the range of +/-20%, the air-fuel ratio may be rich (-20% or less) or lean (+20% or more).

·

When the Coolant Temp in the freeze frame data is less than 75°C (167°F), the misfires occurred only while warming up the engine.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO MISFIRE DTCS)
a.

Connect the intelligent tester or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester or Techstream on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 206

e.

Read DTCs.

Result:
Result Proceed to
P0300, P0301, P0302, P0303 and/or P0304 A
P0300, P0301, P0302, P0303 and/or P0304 and other DTCs B


HINT:

If any DTCs other than P0300, P0301, P0302, P0303 and P0304 are output, troubleshoot those DTCs first.




A

2.CHECK VENTILATION HOSE CONNECTIONS

B

2.CHECK VENTILATION HOSE CONNECTIONS
a.

Check the ventilation hose connections.

Click hereEngine / Hybrid System>3SZ-VE EMISSION CONTROL>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION

OK:

Ventilation hose is connected correctly and is not damaged.


Result:
Proceed to
OK
NG




OK

3.CHECK SPARK PLUG

NG

REPAIR OR REPLACE PCV HOSE

3.CHECK SPARK PLUG
a.
A128473E02
0.854,1.781 1.979,2.083 1.125,0.302 10 Electrode Gap

Remove the ignition coil and the spark plug of the misfiring cylinder.


b.

Measure the spark plug electrode gap.

Standard:

0.8 to 0.9 mm (0.032 to 0.035 in.)



c.

Check the electrode for carbon deposits.

Recommended spark plug:
Manufactures Products
DENSO XU22PR9
NGK DCPR7EA-9


NOTICE:

If the electrode gap is larger than standard, replace the spark plug. Do not adjust the electrode gap.



d.

Reinstall the ignition coil and the spark plug.

Result:
Proceed to
OK
NG




OK

4.CHECK FOR SPARKS AND IGNITION

NG

4.CHECK FOR SPARKS AND IGNITION
a.

Check the ignition system.

HINT:

Refer to Ignition System / On-Vehicle Inspection.

Click hereEngine / Hybrid System>3SZ-VE ENGINE CONTROL>IGNITION SYSTEM>ON-VEHICLE INSPECTION


OK:

Spark occurs.


Result:
Proceed to
OK
NG




OK

5.CHECK CYLINDER COMPRESSION PRESSURE OF MISFIRING CYLINDER

NG

CHANGE NORMAL SPARK PLUG AND CHECK SPARK OF MISFIRING CYLINDER

5.CHECK CYLINDER COMPRESSION PRESSURE OF MISFIRING CYLINDER
a.

Measure the cylinder compression pressure of the misfiring cylinder.

Result:
Result Proceed to
OK A
NG B




A

6.CHANGE NORMAL SPARK PLUG AND CHECK SPARK OF MISFIRING CYLINDER

B

CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION

6.CHANGE NORMAL SPARK PLUG AND CHECK SPARK OF MISFIRING CYLINDER
a.

Change the installed spark plug to a spark plug that functions normally.


b.

Perform a spark test.

CAUTION:

Always disconnect all injector connectors.


NOTICE:

Do not crank the engine for more than 2 seconds.


i.

Install the spark plug to the ignition coil and connect the ignition coil connector.


ii.

Disconnect the injector connector.


iii.

Ground the spark plug.


iv.

Check if sparks occur while the engine is being cranked.

OK:

Sparks jump across electrode gap.


Result:
Proceed to
OK
NG





OK

7.INSPECT ECM TERMINAL VOLTAGE OF MISFIRING CYLINDER (#10, #20, #30 AND/OR #40 VOLTAGE)

NG

REPLACE IGNITION COIL ASSEMBLY THEN CONFIRM THAT THERE IS NO MISFIRE

7.INSPECT ECM TERMINAL VOLTAGE OF MISFIRING CYLINDER (#10, #20, #30 AND/OR #40 VOLTAGE)
a.
A141531C20
0.677,0.969 1.01,1.156 0.333,0.188 1.438,0.979 1.771,1.167 0.333,0.188 0.469,2.115 0.885,1.552 true 0.781,2.385 0.958,1.552 true 1.188,2.76 1.063,1.552 true 1.594,2.531 1.135,1.552 true 1.938,2.365 1.375,1.552 true 0.302,2.156 0.667,2.427 0.365,0.271 10 #10 1.083,2.771 1.521,3.094 0.438,0.323 10 #30 0.646,2.417 1.073,2.708 0.427,0.292 10 #20 1.5,2.552 1.875,2.823 0.375,0.271 10 #40 0.198,0.167 0.635,0.531 0.438,0.365 10 *a 1.875,2.385 2.375,2.698 0.5,0.313 10 E01 0.719,0.99 1.198,1.292 0.479,0.302 10 C23 1.49,0.99 1.969,1.271 0.479,0.281 10 C24
*a Rear view of wire harness connector
(to ECM)


Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connections Switch Condition Specified Conditions
C23-4 (#10) - C24-7 (E01) Ignition switch ON 11 to 14 V
C23-3 (#20) - C24-7 (E01) Ignition switch ON 11 to 14 V
C23-2 (#30) - C24-7 (E01) Ignition switch ON 11 to 14 V
C23-1 (#40) - C24-7 (E01) Ignition switch ON 11 to 14 V


Result:
Result Proceed to
NG A
OK B




A

8.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR - ECM)

B

9.CHECK FUEL INJECTOR OF MISFIRING CYLINDER
8.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR - ECM)
a.

Disconnect the fuel injector connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connections Switch Condition Specified Conditions
C5-2 - C23-4 (#10) Always Below 1 Ω
C6-2 - C23-3 (#20) Always Below 1 Ω
C7-2 - C23-2 (#30) Always Below 1 Ω
C8-2 - C23-1 (#40) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connections Switch Condition Specified Conditions
C5-2 or C23-4 (#10) - Body ground Always 10 kΩ or higher
C6-2 or C23-3 (#20) - Body ground Always 10 kΩ or higher
C7-2 or C23-2 (#30) - Body ground Always 10 kΩ or higher
C8-2 or C23-1 (#40) - Body ground Always 10 kΩ or higher



d.

Reconnect the fuel injector connector.


e.

Reconnect the ECM connector.

Result:
Proceed to
OK
NG




OK

9.CHECK FUEL INJECTOR OF MISFIRING CYLINDER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK FUEL INJECTOR OF MISFIRING CYLINDER
a.

Check the injector injection (whether fuel volume is high or low, and whether injection pattern is poor).

Click hereEngine / Hybrid System>3SZ-VE FUEL>FUEL INJECTOR>INSPECTION

Result:
Proceed to
OK
NG




OK

10.CHECK VALVE CLEARANCE OF MISFIRING CYLINDER

NG

REPLACE FUEL INJECTOR ASSEMBLY

10.CHECK VALVE CLEARANCE OF MISFIRING CYLINDER
a.

Check the valve clearance.

Click hereEngine / Hybrid System>3SZ-VE ENGINE MECHANICAL>VALVE CLEARANCE>ON-VEHICLE INSPECTION

Result:
Proceed to
OK
NG




OK

11.CHECK VALVE TIMING

NG

ADJUST VALVE CLEARANCE

11.CHECK VALVE TIMING
a.

Check the valve timing.

Click hereEngine / Hybrid System>3SZ-VE ENGINE CONTROL>SFI SYSTEM(w/ Rear Heated Oxygen Sensor)>P0011

Result:
Proceed to
OK
NG




OK

12.CHECK FUEL PRESSURE

NG

ADJUST VALVE TIMING

12.CHECK FUEL PRESSURE
a.

Check the fuel pressure.

Click hereEngine / Hybrid System>3SZ-VE FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION

Result:
Proceed to
OK
NG




OK

13.READ VALUE USING INTELLIGENT TESTER OR TECHSTREAM (COOLANT TEMP)

NG

CHECK AND REPLACE FUEL PUMP, PRESSURE REGULATOR, FUEL PIPE LINE AND FILTER

13.READ VALUE USING INTELLIGENT TESTER OR TECHSTREAM (COOLANT TEMP)
a.

Connect the intelligent tester or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester or Techstream on.


d.

Enter the following menus: Powertrain / Engine / Data List / Coolant Temp.

Powertrain > Engine > Data List
Tester Display
Coolant Temp
50003 206 28

e.

Read the Coolant Temp twice, when the engine is both cold and warmed up.

Standard:

With cold engine: Same as ambient air temperature.

With warm engine: 80°C to 102°C (176°F to 216°F).


Result:
Proceed to
OK
NG




OK

14.READ VALUE USING INTELLIGENT TESTER OR TECHSTREAM (MAP)

NG

14.READ VALUE USING INTELLIGENT TESTER OR TECHSTREAM (MAP)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester or Techstream on.


d.

Enter the following menus: Powertrain / Engine / Data List / Coolant Temp and MAP.

Powertrain > Engine > Data List
Tester Display
MAP
Coolant Temp
50003 206 31,28

e.

Allow the engine to idle until the Coolant Temp reaches 80°C (176°F) or more.


f.

Read the MAP with the engine stopped and engine in an idling condition.

Standard:

MAP at engine stopped: 70 to 104 kPa (525 to 780 mmHg)

MAP while engine idling: 20 to 40 kPa (150 to 300 mmHg) (shift position: N, A/C: OFF)


Result:
Proceed to
OK
NG




OK

NG