Home › Engine / Hybrid System › 3SZ-VE ENGINE CONTROL › SFI SYSTEM(w/ Rear Heated Oxygen Sensor) › 2011.11–2015.08
RM19Y0E _51 Engine / Hybrid System _002968 3SZ-VE ENGINE CONTROL _0014988 SFI SYSTEM(w/ Rear Heated Oxygen Sensor) C

3SZ-VE ENGINE CONTROL  SFI SYSTEM(w/ Rear Heated Oxygen Sensor)  P0171  System Too Lean (Bank 1)  P0172  System Too Rich (Bank 1)  


DESCRIPTION

The fuel trim is related to the feedback compensation value, not to the basic injection time. The fuel trim includes the short-term fuel trim and the long-term fuel trim.

The short-term fuel trim is the short-term fuel compensation used to maintain the air-fuel ratio at the stoichiometric air-fuel ratio. The signal from the heated oxygen sensor indicates whether the air-fuel ratio is rich or lean compared to the stoichiometric air-fuel ratio. This variance triggers a reduction in the fuel volume if the air-fuel ratio is rich, and an increase in the fuel volume if it is lean.

The short-term fuel trim varies from the central value due to individual engine differences, wear over time and changes in the operating environment. The long-term fuel trim, which controls the overall fuel compensation, adjusts for long-term deviations of the short-term fuel trim from the central value.

If both the short-term fuel trim and the long-term fuel trim are lean or rich beyond a certain value, the ECM determines this to be a malfunction, illuminates the MIL and sets a DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0171 System Too Lean (Bank 1) When air-fuel ratio feedback stable after warming up engine, fuel trim considerably in error on lean side (2 trip detection logic)
·

Fuel injector blockage

·

Manifold absolute pressure sensor

·

Engine coolant temperature sensor

·

Fuel pressure

·

Gas leak from exhaust system

·

Open or short in heated oxygen sensor (sensor 1) circuit

·

Heated oxygen sensor (sensor 1)

·

Heated oxygen sensor heater (sensor 1)

·

Ventilation hose

·

Running out of fuel

·

ECM


Comes on DTC stored
P0172 System Too Rich (Bank 1) When air-fuel ratio feedback stable after warming up engine, fuel trim considerably in error on rich side (2 trip detection logic)
·

Injector leakage or blockage

·

Manifold absolute pressure sensor

·

Engine coolant temperature sensor

·

Ignition system

·

Fuel pressure

·

Gas leak from exhaust system

·

Open or short in heated oxygen sensor (sensor 1) circuit

·

Heated oxygen sensor (sensor 1)

·

Heated oxygen sensor heater (sensor 1)

·

ECM


Comes on DTC stored

HINT:
·

When DTC P0171 is recorded, the actual air-fuel ratio is on the lean side (Fuel trim corrected heavily on increase side). When DTC P0172 is recorded, the actual air-fuel ratio is on the rich side (Fuel trim corrected heavily on decrease side).

·

If the vehicle runs out of fuel, the air-fuel ratio is lean and DTC P0171 may be recorded. The MIL is then illuminated.

·

When the total of the short-term and long-term fuel trim values is within +/-25% (and ECT is more than 75°C (167°F)), the system is functioning normally.



CAUTION / NOTICE / HINT

HINT:
·

Read freeze frame data using the intelligent tester or Techstream. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data, from the time the malfunction occurred.

·

A high heated oxygen sensor voltage (0.5 V or more) indicates a rich air-fuel ratio.

·

A low heated oxygen sensor voltage (0.4 V or less) indicates a lean air-fuel ratio.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0171 OR P0172)
a.

Connect the intelligent tester or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester or Techstream on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 206

e.

Read DTCs.

Result:
Result Proceed to
P0171 or P0172 A
P0171 or P0172 and other DTCs B


HINT:

If any DTCs other than P0171 or P0172 are output, troubleshoot those DTCs first.




A

2.READ VALUE USING INTELLIGENT TESTER OR TECHSTREAM (COOLANT TEMP)

B

2.READ VALUE USING INTELLIGENT TESTER OR TECHSTREAM (COOLANT TEMP)
a.

Connect the intelligent tester or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester or Techstream on.


d.

Enter the following menus: Powertrain / Engine / Data List / Coolant Temp.

Powertrain > Engine > Data List
Tester Display
Coolant Temp
50003 206 28

e.

Read the Coolant Temp twice, when the engine is both cold and warmed up.

Standard:

With cold engine: Same as ambient air temperature.

With warm engine: 80°C to 102°C (176°F to 216°F).


Result:
Proceed to
OK
NG




OK

3.READ VALUE USING INTELLIGENT TESTER OR TECHSTREAM (MAP)

NG

3.READ VALUE USING INTELLIGENT TESTER OR TECHSTREAM (MAP)
a.

Connect the intelligent tester or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester or Techstream on.


d.

Enter the following menus: Powertrain / Engine / Data List / Coolant Temp and MAP.

Powertrain > Engine > Data List
Tester Display
MAP
Coolant Temp
50003 206 31,28

e.

Allow the engine to idle until the Coolant Temp reaches 80°C (176°F) or more.


f.

Read the MAP with the engine stopped and engine in an idling condition.

Standard:

MAP at engine stopped: 70 to 104 kPa (525 to 780 mmHg)

MAP while engine idling: 20 to 40 kPa (150 to 300 mmHg) (shift position: N, A/C: OFF).


Result:
Proceed to
OK
NG




OK

4.CHECK VENTILATION HOSE

NG

4.CHECK VENTILATION HOSE

OK

5.CHECK FOR SPARK AND IGNITION

NG

REPAIR OR REPLACE VENTILATION HOSE

5.CHECK FOR SPARK AND IGNITION

OK

6.CHECK FOR EXHAUST GAS LEAK

NG

REPAIR OR REPLACE IGNITION SYSTEM

6.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leak.

OK:

No gas leak.


Result:
Proceed to
OK
NG




OK

7.CHECK FUEL PRESSURE

NG

REPAIR OR REPLACE EXHAUST SYSTEM

7.CHECK FUEL PRESSURE

OK

8.INSPECT FUEL INJECTOR ASSEMBLY (INJECTION AND VOLUME)

NG

REPAIR OR REPLACE FUEL SYSTEM

8.INSPECT FUEL INJECTOR ASSEMBLY (INJECTION AND VOLUME)

OK

9.READ VALUE USING INTELLIGENT TESTER OR TECHSTREAM (OUTPUT VOLTAGE OF HEATED OXYGEN SENSOR (SENSOR 1))

NG

9.READ VALUE USING INTELLIGENT TESTER OR TECHSTREAM (OUTPUT VOLTAGE OF HEATED OXYGEN SENSOR (SENSOR 1))
a.

Connect the intelligent tester or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester or Techstream on.


d.

Enter the following menus: Powertrain / Engine / Data List / O2S B1 S1.

Powertrain > Engine > Data List
Tester Display
O2S B1 S1
50003 206 37

e.

Warm up the engine.


f.

Allow the engine to run for 90 seconds at 2500 rpm.


g.
A149559E03
0.375,1.073 0.792,1.417 0.417,0.344 10 1 V 0.396,2.604 0.885,2.99 0.49,0.385 10 0 V 2.875,2.677 3.427,3 0.552,0.323 10 Time 0.073,0.229 2.25,0.604 2.177,0.375 10 Heated Oxygen Sensor Output 0.042,1.74 0.708,2.063 0.667,0.323 10 0.4 V 0.031,1.865 0.823,2.219 0.792,0.354 10 or more

Read the output voltage of the heated oxygen sensor (sensor 1) when the engine is idling and revving up.

OK:

Fluctuates with an amplitude of 0.4 V or more.


Result:
Proceed to
OK
NG




OK

10.PERFORM CONFIRMATION DRIVING PATTERN

NG

12.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)
10.PERFORM CONFIRMATION DRIVING PATTERN
A286301E01
3.188,0.292 5.094,0.708 1.906,0.417 10 2 minutes or more 0.885,0.406 1.938,0.813 1.052,0.406 10 Vehicle Speed 0.75,0.948 1.969,1.344 1.219,0.396 10 70 km/h (43 mph) 0.75,1.813 1.969,2.208 1.219,0.396 10 Ignition Switch off 2.302,2.24 3.052,2.542 0.75,0.302 10 Warm Up 4.875,1.958 5.625,2.26 0.75,0.302 10 Time 2.469,1.531 2.927,1.729 0.458,0.198 10 (d) 3.719,1.094 4.177,1.292 0.458,0.198 10 (e) 4.948,1.542 5.406,1.74 0.458,0.198 10 (f)

a.

Disconnect the negative battery cable for more than 1 minute to clear the air-fuel ratio learning value.


b.

Connect the intelligent tester or Techstream to the DLC3.


c.

Turn the ignition switch to ON and turn the intelligent tester or Techstream on.


d.

Start the engine and warm it up.


e.

Drive the vehicle at a vehicle speed of 70 km/h (43 mph) for 2 minutes or more.


f.

Turn the ignition switch off.


g.

Repeat steps (d) and (e), in order to set DTCs (using 2 trip detection logic).

HINT:

The MIL is illuminated during step (e) if a malfunction still exists.


NOTICE:

If the conditions in this test are not strictly followed, malfunctions may not be detected.


Result:
Proceed to
NEXT




NEXT

11.CHECK WHETHER DTC OUTPUT RECURS (DTC P0171 OR P0172)
11.CHECK WHETHER DTC OUTPUT RECURS (DTC P0171 OR P0172)
a.

Connect the intelligent tester or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester or Techstream on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 206

e.

Read DTCs.

Result:
Result Proceed to
P0171 or P0172 A
No output B




A

12.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)

B

17.CONFIRM IF VEHICLE HAS RUN OUT OF FUEL IN PAST
12.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)
a.

Inspect the heated oxygen sensor (sensor 1).

Click hereEngine / Hybrid System>3SZ-VE ENGINE CONTROL>HEATED OXYGEN SENSOR(w/ Rear Heated Oxygen Sensor)>INSPECTION

Result:
Proceed to
OK
NG




OK

13.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR (SENSOR 1) - ECM)

NG

13.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR (SENSOR 1) - ECM)
a.

Disconnect the heated oxygen sensor (sensor 1) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
For LHD
Tester Connections Condition Specified Conditions
C22-3 (+) - C24-11 (OX) Always Below 1 Ω
C22-1 (HTR-) - C24-3 (OXH1) Always Below 1 Ω
C22-4 (E) - C24-33 (E2) Always Below 1 Ω


Standard Resistance (Check for Open):
For RHD
Tester Connections Condition Specified Conditions
C26-3 (+) - C24-11 (OX) Always Below 1 Ω
C26-1 (HTR-) - C24-3 (OXH1) Always Below 1 Ω
C26-4 (E) - C24-33 (E2) Always Below 1 Ω


Standard Resistance (Check for Short):
For LHD
Tester Connections Condition Specified Conditions
C22-3 (+) or C24-11 (OX) - Body ground Always 10 kΩ or higher
C22-1 (HTR-) or C24-3 (OXH1) - Body ground Always 10 kΩ or higher


Standard Resistance (Check for Short):
For RHD
Tester Connections Condition Specified Conditions
C26-3 (+) or C24-11 (OX) - Body ground Always 10 kΩ or higher
C26-1 (HTR-) or C24-3 (OXH1) - Body ground Always 10 kΩ or higher



d.

Reconnect the heated oxygen sensor (sensor 1) connector.


e.

Reconnect the ECM connector.

Result:
Proceed to
OK
NG




OK

14.REPLACE HEATED OXYGEN SENSOR (SENSOR 1)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.REPLACE HEATED OXYGEN SENSOR (SENSOR 1)
a.

Replace heated oxygen sensor (sensor 1).

Click hereEngine / Hybrid System>3SZ-VE ENGINE CONTROL>HEATED OXYGEN SENSOR(w/ Rear Heated Oxygen Sensor)>REMOVAL

Result:
Proceed to
NEXT




NEXT

15.PERFORM CONFIRMATION DRIVING PATTERN
15.PERFORM CONFIRMATION DRIVING PATTERN
A286301E02
3.188,0.292 5.094,0.708 1.906,0.417 10 2 minutes or more 0.885,0.406 1.938,0.813 1.052,0.406 10 Vehicle Speed 0.75,0.948 1.969,1.344 1.219,0.396 10 70 km/h (43 mph) 0.75,1.813 1.969,2.208 1.219,0.396 10 Ignition Switch off 2.302,2.24 3.052,2.542 0.75,0.302 10 Warm Up 4.875,1.958 5.625,2.26 0.75,0.302 10 Time 2.469,1.531 2.927,1.729 0.458,0.198 10 (d) 3.719,1.094 4.177,1.292 0.458,0.198 10 (e) 4.948,1.542 5.406,1.74 0.458,0.198 10 (f)

a.

Disconnect the negative battery cable for more than 1 minute to clear the air-fuel ratio learning value.


b.

Connect the intelligent tester or Techstream to the DLC3.


c.

Turn the ignition switch to ON and turn the intelligent tester or Techstream on.


d.

Start the engine and warm it up.


e.

Drive the vehicle at a vehicle speed of 70 km/h (43 mph) for 2 minutes or more.


f.

Turn the ignition switch off.


g.

Repeat steps (d) and (e), in order to set DTCs (using 2 trip detection logic).

HINT:

The MIL is illuminated during step (e) if a malfunction still exists.


NOTICE:

If the conditions in this test are not strictly followed, malfunctions may not be detected.


Result:
Proceed to
NEXT




NEXT

16.CHECK WHETHER DTC OUTPUT RECURS (DTC P0171 OR P0172)
16.CHECK WHETHER DTC OUTPUT RECURS (DTC P0171 OR P0172)
a.

Connect the intelligent tester or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester or Techstream on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 206

e.

Read DTCs.

Result:
Result Proceed to
No output A
P0171 or P0172 (for LHD) B
P0171 or P0172 (for RHD) C




A

17.CONFIRM IF VEHICLE HAS RUN OUT OF FUEL IN PAST

B

C

17.CONFIRM IF VEHICLE HAS RUN OUT OF FUEL IN PAST
Result:
Proceed to
YES
NO



YES

DTC CAUSED BY RUNNING OUT OF FUEL

NO