Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › 2011.11–2015.08
RM19Y0E _54 Brake _002992 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0015137 ANTI-LOCK BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  C0278/11  Open in ABS Solenoid Relay Circuit  C0279/12  Short to B+ in ABS Solenoid Relay Circuit  


DESCRIPTION

The ABS solenoid relay supplies power to the ABS solenoid.

After the ignition switch is turned to ON, if the ABS initial check completes, the skid control ECU (brake actuator assembly) turns the ABS solenoid relay on.

The ABS solenoid relay is housed in the skid control ECU in the brake actuator assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area
C0278/11 Open in ABS Solenoid Relay Circuit
1.

Both conditions continue for 0.2 seconds or more.

·

The +IG terminal voltage is between 10 and 16 V.

·

Relay contact is open when the relay is on.


2.

Both conditions are met for 0.2 seconds or more.

·

The +IG terminal voltage is below 10 V.

·

Relay contact remains open.



·

ABS NO. 2 fuse

·

ABS solenoid relay circuit

·

Skid control ECU (Brake actuator assembly)


C0279/12 Short to B+ in ABS Solenoid Relay Circuit Immediately after the ignition switch is turned to ON, the solenoid relay contact is closed for 4.5 seconds when the relay is turned off.
·

ABS solenoid relay circuit

·

Skid control ECU (Brake actuator assembly)



WIRING DIAGRAM

Refer to DTCs C0226/52, C0236/54, C0246/56 and C0256/58 (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>C0226/52).

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

If the brake actuator is replaced with a new one, the skid control ECU (brake actuator assembly) makes the shift to test mode automatically when the ignition switch is turned to ON for the first time. Be sure to complete the test mode checks (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>TEST MODE PROCEDURE).



PROCEDURE

1.CHECK TERMINAL VOLTAGE (+BS TERMINAL)
C248686C03
1.458,0.583 1.948,0.875 0.49,0.292 2.469,1.521 2.469,0.688 2.469,0.688 2.781,0.688 true 0.167,0.115 0.656,0.49 0.49,0.375 10 *a 1.583,0.646 2.115,1 0.531,0.354 10 B10 2.823,0.604 3.385,1.01 0.563,0.406 10 +BS
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator assembly))


a.

Turn the ignition switch off.


b.

Disconnect the B10 skid control ECU (brake actuator assembly) connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
B10-12 (+BS) - Body ground Always 11 to 14 V


Result:
Proceed to
OK
NG




OK

2.CHECK HARNESS AND CONNECTOR (GROUND CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (GROUND CIRCUIT)
a.

Turn the ignition switch off.


b.

Disconnect the B10 skid control ECU (brake actuator assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B10-1 (GND1) - Body ground Always Below 1 Ω
B10-13 (GND2) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG




OK

3.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.RECONFIRM DTC
HINT:

These codes are stored when a problem is identified in the skid control ECU (brake actuator assembly).

The solenoid circuit is in the brake actuator assembly. Therefore, the solenoid circuit inspection and solenoid unit inspection cannot be performed. Be sure to check if any DTCs are output before replacing the brake actuator assembly.


a.

Clear the DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 509

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 20 km/h (12 mph) or more.


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 509
Result:
Result Proceed to
DTC not output A
DTC output B


HINT:
·

If a speed signal of 6 km/h (4 mph) or more is input to the skid control ECU (brake actuator assembly) with the ignition switch ON and the stop light switch off, the ECU performs self diagnosis of the motor and solenoid circuits.

·

If the normal system code is output (the trouble code is not output), slightly jiggle the connectors, wire harnesses and fuses of the skid control ECU (brake actuator assembly). Make sure that no DTCs are output.

·

If any DTCs are output while jiggling a connector or wire harness of the skid control ECU (brake actuator assembly), inspect and repair the connector or wire harness.

·

It is suspected that the DTCs were output due to a bad connection of the connector terminal.





A

B