Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › 2011.11–2015.08
RM19Y0E _54 Brake _002992 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0015137 ANTI-LOCK BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  C1249/39  Open in Stop Light Switch Circuit  


DESCRIPTION

The skid control ECU (brake actuator assembly) has an open detection circuit, which outputs this DTC when detecting open circuits in the stop light input line of the stop light LH and RH circuits or an open in the ground line with the stop light switch off (brake pedal not depressed).

DTC No. Detection Item DTC Detection Condition Trouble Area
C1249/39 Open in Stop Light Switch Circuit When ECU terminal +IG voltage 10 V to 16.0 V and ABS non-operational, open in stop light switch circuit continues for 0.3 seconds or more.
·

Stop light switch circuit

·

Stop light LH and RH circuits

·

Skid control ECU (Brake actuator assembly)



WIRING DIAGRAM

C248688E02
4.198,2.854 6.177,3.615 1.979,0.76 10 SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) 4.198,2.688 4.76,3.073 0.563,0.385 10 B10 4.427,0.396 5.135,0.813 0.708,0.417 10 STP 0.365,0.396 2.281,1 1.917,0.604 10 from Stop Light Switch 0.677,3.01 3.417,3.802 2.74,0.792 10 STOP LIGHT LH (REAR COMBINATION LIGHT ASSEMBLY LH) 4.198,0.313 4.625,0.719 0.427,0.406 10 28 1.677,2.49 2.063,2.865 0.385,0.375 10 2 0.896,2.5 1.344,2.875 0.448,0.375 10 5 1.51,2.573 1.792,2.896 0.281,0.323 10 + 1.063,2.573 1.375,2.885 0.313,0.313 10 - 1.677,1.146 2.073,1.542 0.396,0.396 10 2 0.896,1.156 1.25,1.51 0.354,0.354 10 5 1.5,1.229 1.854,1.583 0.354,0.354 10 + 1.063,1.229 1.406,1.542 0.344,0.313 10 - 5.49,1.865 6.313,2.271 0.823,0.406 10 GND1 5.49,2.198 6.24,2.615 0.75,0.417 10 GND2 0.688,2.833 1.156,3.156 0.469,0.323 10 J4 0.708,1.646 3.302,2.375 2.594,0.729 10 STOP LIGHT RH (REAR COMBINATION LIGHT ASSEMBLY RH) 0.708,1.469 1.177,1.865 0.469,0.396 10 J9 5.99,1.781 6.417,2.156 0.427,0.375 10 1 5.958,2.115 6.521,2.49 0.563,0.375 10 13

CAUTION / NOTICE / HINT

NOTICE:

If the brake actuator is replaced with a new one, the skid control ECU (brake actuator assembly) makes the shift to test mode automatically when the ignition switch is turned to ON for the first time. Be sure to complete the test mode checks (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>TEST MODE PROCEDURE).


PROCEDURE

1.CHECK STOP LIGHT OPERATION
a.

Check that the stop light LH and RH come on when the brake pedal is depressed, and go off when the brake pedal is released.

OK:
Condition Illumination Condition
Brake pedal depressed On
Brake pedal released Off


Result:
Proceed to
OK
NG




OK

2.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SW)

NG

GO TO LIGHTING SYSTEM (PROBLEM SYMPTOMS TABLE)

2.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SW)
a.

Turn the ignition switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the intelligent tester on.


e.

Enter the following menus: Chassis / ABS/VSC / Data List.

Chassis > ABS/VSC/TRC > Data List
Tester Display
Stop Light Switch
50003 509 11
Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light Switch Stop light switch ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-

f.

Using the intelligent tester, check the input of the stop light switch operation when the brake pedal is operated.

OK:

When the brake pedal is operated, the display changes as shown above.


Result:
Proceed to
OK
NG




OK

3.RECONFIRM DTC

NG

4.CHECK TERMINAL VOLTAGE (STP TERMINAL)
3.RECONFIRM DTC
a.

Clear the DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 509

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE

Chassis > ABS/VSC/TRC > Trouble Codes
50001 509
Result:
Result Proceed to
DTC not output A
DTC output B


HINT:

If troubleshooting has been carried out according to the problem symptoms table, refer back to the table and proceed to the next step.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR




A

B

4.CHECK TERMINAL VOLTAGE (STP TERMINAL)
a.
C248686C05
1.458,0.635 1.948,0.927 0.49,0.292 1.531,2.104 1.531,2.74 true 0.135,0.094 0.625,0.438 0.49,0.344 10 *a 1.583,0.698 2.26,1.063 0.677,0.365 10 B10 1.354,2.76 1.948,3.125 0.594,0.365 10 STP
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Turn the ignition switch off.


b.

Disconnect the B10 skid control ECU (brake actuator assembly) connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
B10-28 (STP) - Body ground Brake pedal depressed 8 to 14 V
Brake pedal released Below 1.5 V


Result:
Proceed to
OK
NG




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR