Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › 2011.11–2015.08
RM19Y0E _54 Brake _002992 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0015137 ANTI-LOCK BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  C1241/15  Low Battery Voltage  C1241/16  High Battery Voltage  


DESCRIPTION

This DTC is stored when the +IG terminal voltage deviates from the DTC detection condition due to a malfunction in the power supply or charging circuit, such as the battery or generator circuit, etc.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1241/15 Low Battery Voltage When any of the following is detected:
1.

At a vehicle speed of 3 km/h (2 mph) or more, the +IG terminal voltage is less than 9.5 V for 10 seconds or more.

2.

When the solenoid relay remains on and the +IG terminal voltage is less than 9.5 V, the relay contact is open for 0.22 seconds or more.

3.

With the +IG terminal voltage 9.5 V or less, the vehicle speed sensor power supply decreases for 60 seconds or more.

4.

When the motor fail safe relay is on after the motor relay turns on, the +IG terminal voltage is 9.5 V or less and the actuator pump drive motor is off for 0.12 seconds or more.


·

ECU IG1 fuse

·

Battery

·

Charging system

·

Power source circuit

·

Internal power supply circuit of skid control ECU (Brake actuator assembly)


C1241/16 High Battery Voltage When any of the following is detected:
1.

At a vehicle speed of 3 km/h (2 mph) or more, the +IG terminal voltage is less than 9.5 V for 10 seconds or more.

2.

When the solenoid relay remains on and the +IG terminal voltage is less than 9.5 V, the relay contact is open for 0.22 seconds or more.

3.

With the +IG terminal voltage 9.5 V or less, the vehicle speed sensor power supply decreases for 60 seconds or more.

4.

When the motor fail safe relay is on after the motor relay turns on, the +IG terminal voltage is 9.5 V or less and the actuator pump drive motor is off for 0.12 seconds or more.


·

ECU IG1 fuse

·

Battery

·

Charging system

·

Power source circuit

·

Internal power supply circuit of skid control ECU (Brake actuator assembly)



WIRING DIAGRAM

C248687E02
4.521,3.031 6.563,3.802 2.042,0.771 10 SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) 4.521,2.844 5.26,3.219 0.74,0.375 10 B10 4.854,0.823 5.427,1.177 0.573,0.354 10 +IG 2.76,0.99 3.719,1.458 0.958,0.469 10 ECU IG1 0.635,0.813 2,1.406 1.365,0.594 10 from IG Circuit 4.625,0.74 5.26,1.188 0.635,0.448 10 34 4.854,1.521 5.719,2.031 0.865,0.51 10 GND1 4.854,2.177 5.677,2.677 0.823,0.5 10 GND2 4.698,1.438 5.073,1.802 0.375,0.365 10 1 4.625,2.083 5.083,2.458 0.458,0.375 10 13

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

If the brake actuator is replaced with a new one, the skid control ECU (brake actuator assembly) makes the shift to test mode automatically when the ignition switch is turned to ON for the first time. Be sure to complete the test mode checks (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>TEST MODE PROCEDURE).



PROCEDURE

1.INSPECT BATTERY
a.

Check the battery voltage.

Standard voltage:

11 to 14 V


Result:
Result Proceed to
OK A
NG (for 3SZ-VE) B
NG (for K3-VE) C




A

2.CHECK TERMINAL VOLTAGE (+IG TERMINAL)

B

C

2.CHECK TERMINAL VOLTAGE (+IG TERMINAL)
a.
C248686C04
1.458,0.635 1.948,0.927 0.49,0.292 2.271,2.104 2.271,2.708 true 0.135,0.094 0.531,0.521 0.396,0.427 10 *a 1.583,0.698 2.208,1.094 0.625,0.396 10 B10 2.115,2.729 2.729,3.083 0.615,0.354 10 +IG
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Turn the ignition switch off.


b.

Disconnect the B10 skid control ECU (brake actuator assembly) connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
B10-34 (+IG) - Body ground Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG




OK

3.CHECK HARNESS AND CONNECTOR (GROUND CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (GROUND CIRCUIT)
a.

Turn the ignition switch off.


b.

Disconnect the B10 skid control ECU (brake actuator assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B10-1 (GND1) - Body ground Always Below 1 Ω
B10-13 (GND2) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG




OK

4.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.RECONFIRM DTC
a.

Clear the DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 509

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 20 km/h (12 mph) or more.


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE

Chassis > ABS/VSC/TRC > Trouble Codes
50001 509
Result:
Result Proceed to
DTC not output A
DTC output B


HINT:

If troubleshooting has been carried out according to the problem symptoms table, refer back to the table and proceed to the next step.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR




A

B