Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2011.11–2015.08
RM19Y0E _57 Power Source / Network _003004 NETWORKING _0015181 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Open in CAN Main Bus Line  


DESCRIPTION

There may be an open circuit in one of the V Bus main lines and/or a DLC3 branch line when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is 70 Ω or higher.

Symptom Trouble Area
Resistance between terminals 6 (CANH) and 14 (CANL) of DLC3 is 70 Ω or higher.
·

DLC3 branch line or connector

·

CAN main bus line or connector

·

ECM

·

TCM*1

·

Combination meter assembly*2

·

CAN No. 1 junction connector



*1 : for A/T

*2 : w/ Multi Information Display

This malfunction is not related to the lines of a CAN main bus branch or to ECUs connected to the CAN main bus branch.

WIRING DIAGRAM

C243549E03
0.052,0.094 1.76,1.01 1.708,0.917 12 w/ Multi Information Display : 5.521,1.823 6.063,2.24 0.542,0.417 10 DLC3 2.01,0.26 2.5,0.625 0.49,0.365 10 ECM 0.969,3 2.521,3.792 1.552,0.792 10 CAN NO. 1 JUNCTION CONNECTOR 4.375,5.115 5.781,5.958 1.406,0.844 10 COMBINATION METER ASSEMBLY 2.542,1.677 3.135,2.042 0.594,0.365 10 CANL 5.5,1.375 6.115,1.781 0.615,0.406 10 CANL 3.802,1.667 4.396,2.052 0.594,0.385 10 CANH 2.521,4.927 3.115,5.313 0.594,0.385 10 CANL 3.802,4.917 4.365,5.26 0.563,0.344 10 CANH 5.417,1.083 6.083,1.469 0.667,0.385 10 CANH 3.865,0.969 4.5,1.323 0.635,0.354 10 HCAN 3.865,1.438 4.521,1.792 0.656,0.354 10 LCAN 3.167,5.51 3.719,5.823 0.552,0.313 10 120 Ω 3.167,0.135 3.75,0.51 0.583,0.375 10 120 Ω 2.833,1.885 3.208,2.24 0.375,0.354 10 3 3.813,1.885 4.188,2.271 0.375,0.385 10 4 2.76,2.604 3.156,2.906 0.396,0.302 10 10 4.854,1.521 5.229,1.906 0.375,0.385 10 W 4.865,0.906 5.198,1.208 0.333,0.302 10 B 3.813,2.625 4.177,2.979 0.365,0.354 10 8 2.74,2.26 3.083,2.552 0.344,0.292 10 G 3.823,2.281 4.25,2.635 0.427,0.354 10 R 2.729,4.375 3.135,4.677 0.406,0.302 10 W 3.833,4.385 4.24,4.781 0.406,0.396 10 B 2.833,4.031 3.125,4.333 0.292,0.302 10 3 3.802,4.021 4.198,4.375 0.396,0.354 10 1 2.76,4.719 3.125,5.052 0.365,0.333 10 29 3.802,4.708 4.188,5.031 0.385,0.323 10 28 5.115,0.99 5.5,1.323 0.385,0.333 10 6 5.188,1.479 5.552,1.802 0.365,0.323 10 14 4.385,0.99 4.74,1.323 0.354,0.333 10 2 4.375,1.479 4.729,1.813 0.354,0.333 10 1 4.375,4.938 5,5.302 0.625,0.365 10 E34 2.01,0.083 2.479,0.469 0.469,0.385 10 E3 0.969,2.833 1.573,3.208 0.604,0.375 10 E45 5.521,1.677 6.052,2.031 0.531,0.354 10 E12 0.875,5.948 2.938,6.458 2.063,0.51 10 : CAN Main Bus Line (CANH) 0.875,6.354 3.031,6.833 2.156,0.479 10 : CAN Main Bus Line (CANL) 4.198,5.927 6.271,6.396 2.073,0.469 10 : CAN Branch Bus Line (CANH) 4.208,6.302 6.313,6.771 2.104,0.469 10 : CAN Branch Bus Line (CANL)

C243557E06
0.063,0.104 1.688,0.906 1.625,0.802 12 w/o Multi Information Display : 5.521,1.854 6.073,2.281 0.552,0.427 10 DLC3 2.031,0.302 2.479,0.698 0.448,0.396 10 ECM 2.563,1.688 3.094,2.031 0.531,0.344 10 CANL 5.5,1.354 6.104,1.708 0.604,0.354 10 CANL 3.813,1.667 4.479,2.031 0.667,0.365 10 CANH 2.521,3.021 3,3.396 0.479,0.375 10 CANL 3.813,3.031 4.365,3.458 0.552,0.427 10 CANH 5.427,1.104 6.021,1.521 0.594,0.417 10 CANH 3.875,0.99 4.396,1.323 0.521,0.333 10 HCAN 3.875,1.458 4.458,1.802 0.583,0.344 10 LCAN 3.188,3.594 3.813,3.99 0.625,0.396 10 120 Ω 3.177,0.146 3.708,0.552 0.531,0.406 10 120 Ω 2.823,1.917 3.167,2.24 0.344,0.323 10 3 3.823,1.906 4.177,2.208 0.354,0.302 10 4 4.865,1.542 5.292,1.917 0.427,0.375 10 W 4.885,0.906 5.292,1.25 0.406,0.344 10 B 2.75,2.302 2.938,2.458 0.188,0.156 10 G 3.833,2.292 4.135,2.615 0.302,0.323 10 R 5.125,1 5.5,1.354 0.375,0.354 10 6 5.198,1.479 5.563,1.823 0.365,0.344 10 14 4.396,1 4.781,1.375 0.385,0.375 10 2 4.396,1.479 4.75,1.854 0.354,0.375 10 1 2.031,0.156 2.417,0.469 0.385,0.313 10 E3 5.531,1.698 6.063,2.052 0.531,0.354 10 E12 0.885,4.031 2.771,4.49 1.885,0.458 10 : CAN Main Bus Line (CANH) 0.875,4.406 2.781,4.802 1.906,0.396 10 : CAN Main Bus Line (CANL) 4.208,4.01 6.281,4.51 2.073,0.5 10 : CAN Branch Bus Line (CANH) 4.208,4.396 6.281,4.813 2.073,0.417 10 : CAN Branch Bus Line (CANL) 3.823,2.792 4.167,3.083 0.344,0.292 10 7 2.771,2.802 3.146,3.083 0.375,0.281 10 17 4.375,2.979 4.813,3.281 0.438,0.302 10 E9 4.385,3.146 4.906,3.563 0.521,0.417 10 TCM* 0.271,3.458 1.063,3.927 0.792,0.469 10 * : for A/T

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>Open in CAN Main Bus Line).

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the ignition switch to ON, wait at least 5 seconds.

·

After the repair, perform CAN Bus Check and check that all the ECUs connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (DLC3 BRANCH LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
E231257C01
1.448,0.26 1.938,0.552 0.49,0.292 2.25,0.469 2,0.927 true 1.896,1.479 1.646,1.927 true 0.104,0.094 0.479,0.406 0.375,0.313 10 *a 2.281,0.365 2.875,0.729 0.594,0.365 10 CANH 1.271,1.865 1.792,2.177 0.521,0.313 10 CANL 1.542,0.323 2.031,0.667 0.49,0.344 10 E12
*a Front view of DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E12-6 (CANH) - E12-14 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω


NOTICE:

When the measured value is 133 Ω or higher and a CAN communication system DTC is output, there may be a fault besides disconnection of the DLC3 branch line. For that reason, troubleshooting should be performed again from How to Proceed with Troubleshooting after repairing the trouble area.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING


Result:
proceed to
OK
NG




OK

2.SYSTEM CHECK

NG

REPAIR OR REPLACE CAN BRANCH LINE CONNECTED TO DLC3

2.SYSTEM CHECK
a.

Check the vehicle specifications.

Result:
Result Proceed to
for A/T
w/ Multi Information Display
A
for M/T
w/ Multi Information Display
B
for A/T
w/o Multi Information Display
C




A

3.CHECK FOR OPEN IN CAN BUS LINES (ECM - CAN NO. 1 JUNCTION CONNECTOR)

B

6.CHECK FOR OPEN IN CAN BUS LINES (ECM - COMBINATION METER ASSEMBLY)

C

8.CHECK FOR OPEN IN CAN BUS LINES (ECM - TCM)
3.CHECK FOR OPEN IN CAN BUS LINES (ECM - CAN NO. 1 JUNCTION CONNECTOR)
C243555C02
1.896,1.135 2.385,1.427 0.49,0.292 2.417,1.719 2.177,2.313 true 1.667,2.094 2.094,2.323 true 0.094,0.083 0.479,0.427 0.385,0.344 10 *a 2.021,1.198 2.313,1.354 0.292,0.156 10 E3 2.479,1.646 3.167,1.969 0.688,0.323 10 3 (CANL) 1.052,2.021 1.792,2.385 0.74,0.365 10 4 (CANH)
*a Rear view of wire harness connector
(to ECM)


a.

Disconnect the E3 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E3-4 (CANH) - E3-3 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω


Result:
Result Proceed to
OK (for 3SZ-VE) A
OK (for K3-VE) B
NG C




A

B

C

4.CHECK FOR OPEN IN CAN BUS LINES (COMBINATION METER ASSEMBLY - CAN NO. 1 JUNCTION CONNECTOR)
4.CHECK FOR OPEN IN CAN BUS LINES (COMBINATION METER ASSEMBLY - CAN NO. 1 JUNCTION CONNECTOR)
a.

Reconnect the E3 ECM connector.


b.
C243545C02
1.417,0.615 1.906,0.906 0.49,0.292 1.188,2.375 0.896,2.26 false 1.833,2.167 1.594,2.771 true 1.927,2.167 2.156,2.771 true 0.125,0.115 0.479,0.458 0.354,0.344 10 *a 1.51,0.677 1.948,1 0.438,0.323 10 E34 0.729,2.688 1.563,3.094 0.833,0.406 10 29 (CANL) 2.25,2.698 3.156,3.125 0.906,0.427 10 28 (CANH)
*a Rear view of wire harness connector
(to Combination Meter Assembly)


Disconnect the E34 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E34-28 (CANH) - E34-29 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω


Result:
proceed to
OK
NG




OK

REPLACE COMBINATION METER ASSEMBLY

NG

5.CHECK FOR OPEN IN CAN BUS LINES (CAN NO. 1 JUNCTION CONNECTOR)
5.CHECK FOR OPEN IN CAN BUS LINES (CAN NO. 1 JUNCTION CONNECTOR)
a.

Reconnect the E34 combination meter assembly connector.


b.
C243541C01
0.271,0.74 0.76,1.031 0.49,0.292 2.26,1.052 2.604,1.5 true 2.604,0.323 2.26,0.771 true 1.469,0.323 1.823,0.771 true 1.813,1.083 1.271,1.802 true 0.094,0.052 0.5,0.417 0.406,0.365 10 *a 2.646,0.219 3.083,0.573 0.438,0.354 10 *b 1.313,0.188 1.688,0.51 0.375,0.323 10 *b 2.646,1.448 3.031,1.844 0.385,0.396 10 *c 1.115,1.729 1.458,2.083 0.344,0.354 10 *c 0.365,0.813 0.802,1.115 0.438,0.302 10 E45
*a Rear view of wire harness connector
(to CAN No. 1 Junction Connector)
*b to Combination Meter Assembly
*c to ECM


Disconnect the E45 CAN No. 1 junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
E45-1 - E45-3 Cable disconnected from negative (-) battery terminal 108 to 132 Ω Combination meter assembly
E45-8 - E45-10 Cable disconnected from negative (-) battery terminal 108 to 132 Ω ECM


Result:
Result Proceed to
OK A
NG (Combination meter assembly main line) B
NG (ECM main line) C




A

REPLACE CAN NO. 1 JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 1 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)

C

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 1 JUNCTION CONNECTOR - ECM)

6.CHECK FOR OPEN IN CAN BUS LINES (ECM - COMBINATION METER ASSEMBLY)
a.
C243555C03
1.896,1.135 2.385,1.427 0.49,0.292 2.427,1.729 2.188,2.323 true 1.667,2.094 2.094,2.323 true 0.094,0.083 0.406,0.385 0.313,0.302 10 *a 2.021,1.198 2.313,1.354 0.292,0.156 10 E3 2.479,1.646 3.198,1.99 0.719,0.344 10 3 (CANL) 0.885,2.01 1.573,2.396 0.688,0.385 10 4 (CANH)
*a Rear view of wire harness connector
(to ECM)


Disconnect the E3 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E3-4 (CANH) - E3-3 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω


Result:
Result Proceed to
OK (for 3SZ-VE) A
OK (for K3-VE) B
NG C




A

B

C

7.CHECK FOR OPEN IN CAN BUS LINES (COMBINATION METER ASSEMBLY - ECM)
7.CHECK FOR OPEN IN CAN BUS LINES (COMBINATION METER ASSEMBLY - ECM)
a.

Reconnect the E3 ECM connector.


b.
C243545C03
1.417,0.615 1.906,0.906 0.49,0.292 1.188,2.375 0.896,2.26 false 1.823,2.177 1.583,2.781 true 1.917,2.156 2.146,2.76 true 0.125,0.135 0.51,0.438 0.385,0.302 10 *a 1.51,0.677 1.969,1.031 0.458,0.354 10 E34 0.906,2.708 1.677,3.083 0.771,0.375 10 29 (CANL) 2.198,2.708 3.01,3.073 0.813,0.365 10 28 (CANH)
*a Rear view of wire harness connector
(to Combination Meter Assembly)


Disconnect the E34 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E34-28 (CANH) - E34-29 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω


Result:
proceed to
OK
NG




OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (COMBINATION METER ASSEMBLY - ECM)

8.CHECK FOR OPEN IN CAN BUS LINES (ECM - TCM)
a.
C243555C04
1.896,1.135 2.385,1.427 0.49,0.292 2.417,1.708 2.177,2.302 true 1.667,2.094 2.094,2.323 true 0.094,0.083 0.479,0.479 0.385,0.396 10 *a 2.021,1.198 2.313,1.354 0.292,0.156 10 E3 2.448,1.594 3.302,1.979 0.854,0.385 10 3 (CANL) 1.042,2 1.865,2.365 0.823,0.365 10 4 (CANH)
*a Rear view of wire harness connector
(to ECM)


Disconnect the E3 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E3-4 (CANH) - E3-3 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω


Result:
Result Proceed to
OK (for 3SZ-VE) A
OK (for K3-VE) B
NG C




A

B

C

9.CHECK FOR OPEN IN CAN BUS LINES (TCM - ECM)
9.CHECK FOR OPEN IN CAN BUS LINES (TCM - ECM)
a.

Reconnect the E3 ECM connector.


b.
C243543C03
1.146,0.583 1.635,0.875 0.49,0.292 1.625,2.271 1.969,2.729 true 2.031,2.052 1.635,2.188 true 0.104,0.094 0.51,0.448 0.406,0.354 10 *a 1.292,0.635 1.729,0.969 0.438,0.333 10 E9 2.063,1.979 2.875,2.344 0.813,0.365 10 7 (CANH) 1.99,2.656 2.813,3 0.823,0.344 10 17 (CANL)
*a Rear view of wire harness connector
(to TCM)


Disconnect the E9 TCM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E9-7 (CANH) - E9-17 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω


Result:
proceed to
OK
NG




OK

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (TCM - ECM)