Home › Vehicle Interior › HEATING / AIR CONDITIONING › FRONT AIR CONDITIONING UNIT › 2011.11–2013.04
RM19Y0E _58 Vehicle Interior _003013 HEATING / AIR CONDITIONING _0015227 FRONT AIR CONDITIONING UNIT A

HEATING / AIR CONDITIONING  FRONT AIR CONDITIONING UNIT  INSTALLATION  


PROCEDURE

Hide 1.INSTALL AIR CONDITIONING UNIT ASSEMBLY (for RHD)

a.

Install the air conditioning unit assembly onto the instrument panel reinforcement with the 2 bolts and nut in the order indicated in the illustration.

E236707N01
1.563,0.198 1.771,0.396 0.208,0.198 10 3 4.979,1.677 5.219,1.938 0.24,0.26 10 2 4.688,1.292 4.875,1.479 0.188,0.188 10 1


Hide 2.INSTALL AIR CONDITIONING UNIT ASSEMBLY (for LHD)

a.

Install the air conditioning unit assembly onto the instrument panel reinforcement with the 2 bolts and nut in the order indicated in the illustration.

E237577N01
0.907,1.157 1.04,1.339 0.133,0.182 10 1 1.244,1.75 1.377,1.932 0.133,0.182 10 2 5.471,1.857 5.604,2.039 0.133,0.182 10 3


Hide 55331 3.INSTALL INSTRUMENT PANEL REINFORCEMENT (for RHD)

a.

Install the instrument panel reinforcement with the 5 bolts.


b.

Install the 4 bolts from front pillar.


c.

Install the bolt from engine room.


Hide 55331 4.REMOVE INSTRUMENT PANEL REINFORCEMENT (for LHD)

a.

Install the instrument panel reinforcement with the 4 bolts.


b.

Install the 4 bolts from front pillar.


c.

Install the bolt from engine room.


Hide 88539J 5.INSTALL DRAIN COOLER HOSE

a.

Install the drain cooler hose.

HINT:

Use the same procedure for the RHD and LHD vehicle.



Hide 87220 6.INSTALL AIR DUCT ASSEMBLY

a.

Install the air duct assembly with the 2 bolts.

HINT:

Use the same procedure for the RHD and LHD vehicle.



Hide 82141 7.INSTALL INSTRUMENT PANEL WIRE (for RHD)

a.

Connect the instrument panel wire onto the instrument panel reinforcement with the 2 clamps.


b.

Connect the ground wire onto the instrument panel reinforcement with the bolt.


c.

Connect the ground wire onto the instrument panel reinforcement with the bolt and 3 clamps.


d.

Connect the ground wire onto the instrument panel reinforcement with the bolt.


e.

Connect the connector and 4 clamps.


f.

Connect the 2 connectors and 2 clamps.


Hide 82141 8.INSTALL INSTRUMENT PANEL WIRE (for LHD)

a.

Connect the instrument panel wire onto the instrument panel reinforcement with the 2 clamps.


b.

Connect the ground wire onto the instrument panel reinforcement with the 2 bolts.


c.

Connect the instrument panel wire onto the instrument panel reinforcement with the 3 clamps.


d.

Connect the ground wire onto the instrument panel reinforcement with the bolt.


e.

Connect the ground wire onto the instrument panel reinforcement with the bolt and 3 clamps.


f.

Connect the ground wire onto the instrument panel reinforcement with the bolt.


g.

Connect the connector and clamp.


h.

Connect the connector and 3 clamps.


i.

Connect the ground wire onto the instrument panel reinforcement with the bolt.


j.

Connect the 2 connectors and the clamp.


Hide 82600 9.INSTALL RELAY BLOCK ASSEMBLY (for RHD)

a.

Install the relay block assembly with the 3 bolts.


b.

Connect each connector.


Hide 82600 10.INSTALL RELAY BLOCK ASSEMBLY (for LHD)

a.

Install the relay block assembly with the 3 bolts.


b.

Connect each connector.


Hide 85918A 11.INSTALL DOOR CONTROL RELAY

Hide 89530C 12.INSTALL TCM (for Automatic Transmission)

Hide 45250 15.INSTALL STEERING COLUMN ASSEMBLY

Hide 55303B 16.INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY

Hide 55302A 17.INSTALL UPPER INSTRUMENT PANEL SUB-ASSEMBLY

Hide 88716A 18.INSTALL LIQUID TUBE SUB-ASSEMBLY (for RHD)

a.

Remove the vinyl tape from liquid tube sub-assembly and the connecting portion of the unit.


b.

Apply sufficient compressor oil (ND-OIL8 or equivalent) to a new O-ring and the connecting part of the liquid tube sub-assembly.

Compressor oil:

ND-OIL8 or equivalent



c.

Install the O-ring onto the liquid tube sub-assembly.


d.

Connect the liquid tube onto the air conditioning unit assembly.


Hide 88716A 19.INSTALL LIQUID TUBE SUB-ASSEMBLY (for LHD)

a.

Remove the vinyl tape from liquid tube sub-assembly and the connecting portion of the unit.


b.

Apply sufficient compressor oil (ND-OIL8 or equivalent) to a new O-ring and the connecting part of the liquid tube sub-assembly.

Compressor oil:

ND-OIL8 or equivalent



c.

Install the O-ring onto the liquid tube sub-assembly.


d.

Connect the liquid tube onto the air conditioning unit assembly.


Hide 88717U 20.INSTALL SUCTION TUBE SUB-ASSEMBLY (for RHD)

a.

Remove the vinyl tape from the suction tube sub-assembly and the connecting part of the air conditioning unit assembly.


b.

Apply sufficient compressor oil (ND-OIL8 or equivalent) to a new O-ring and the connecting part of the suction tube sub-assembly.

Compressor oil:

ND-OIL8 or equivalent



c.

Install the O-ring onto the suction tube sub-assembly.


d.

Connect the suction tube onto the air conditioning unit assembly.


e.
E231791

Turn the hook connector in the direction indicated by the arrow in the illustration.


f.

Insert the pipe joints securely into the fitting holes and tighten the new bolt.

Torque:
6.2 N*m (63 kgf*cm, 55 in.*lbf)


Hide 88717U 21.INSTALL SUCTION TUBE SUB-ASSEMBLY (for LHD)

a.

Remove the vinyl tape from the suction tube sub-assembly and the connecting part of the air conditioning unit assembly.


b.

Apply sufficient compressor oil (ND-OIL8 or equivalent) to a new O-ring and the connecting part of the suction tube sub-assembly.

Compressor oil:

ND-OIL8 or equivalent



c.

Install the O-ring onto the suction tube sub-assembly.


d.

Connect the suction tube onto the air conditioning unit assembly.


e.
E238738

Turn the hook connector in the direction indicated by the arrow in the illustration.


f.

Insert the pipe joints securely into the fitting holes and tighten the new bolt.

Torque:
6.2 N*m (63 kgf*cm, 55 in.*lbf)


Hide 87246X 22.INSTALL NO. 2 HEATER WATER HOSE (w/ Heater)

a.

Connect the No. 2 heater water hose with the clamp to the air conditioning unit.

HINT:

Use the same procedure for the RHD and LHD vehicle.



Hide 87245X 23.INSTALL NO. 1 HEATER WATER HOSE (w/ Heater)

a.

Connect the No. 1 heater water hose with the clamp to the air conditioning unit.

HINT:

Use the same procedure for the RHD and LHD vehicle.



Hide 24.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
6.4 N*m (65 kgf*cm, 57 in.*lbf)

Hide 27. WARM UP ENGINE