Home › Engine / Hybrid System › 3SZ-VE COOLING › COOLING FAN SYSTEM › 2014.04–2015.08
RM19Y0E _51 Engine / Hybrid System _002978 3SZ-VE COOLING _0015052 COOLING FAN SYSTEM J

3SZ-VE COOLING  COOLING FAN SYSTEM  Cooling Fan Circuit  


TECHNICAL DESCRIPTION

To control the cooling fan, the ECM turns on and off the cooling fan relay based on the engine coolant temperature, air conditioning switch, refrigerant pressure, engine speed and vehicle speed signals.

On vehicles equipped with a cooling fan resistor, the ECM turns the RAD No. 2 relay on and off to control the cooling fan speed in 2 stages.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK WIRE HARNESS AND CONNECTOR (RAD RELAY VOLTAGE)
a.
A265843C01
0.104,0.104 0.458,0.417 0.354,0.313 10 *1 2.083,1.198 2.521,1.604 0.438,0.406 10 *2
*1 Engine Room Relay Block
*2 RAD Relay Holder


Remove the RAD relay from the engine room relay block.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
RAD relay terminal 3 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK WIRE HARNESS AND CONNECTOR (AM2 VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK WIRE HARNESS AND CONNECTOR (AM2 VOLTAGE)
a.

Disconnect the E28 ignition or starter switch assembly connector.


b.
A325498C02
1.417,0.156 1.906,0.396 0.49,0.24 0.771,1.719 1.552,1.438 true 1.531,0.198 1.99,0.396 0.458,0.198 10 false E28 0.448,1.656 0.906,1.854 0.458,0.198 10 false AM2 0.125,0.115 0.438,0.313 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Ignition or Starter Switch Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E28-5 (AM2) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY
a.

Inspect the ignition or starter switch assembly.

Click hereEngine / Hybrid System>3SZ-VE STARTING>IGNITION SWITCH>INSPECTION

Result:
Proceed to
OK
NG




OK

4.INSPECT RELAY

NG

REPLACE IGNITION OR STARTER SWITCH ASSEMBLY

4.INSPECT RELAY
a.

w/o cooling fan resister



b.

w/ cooling fan resister


ii.


Result:
Proceed to
OK
NG



OK

5.CHECK WIRE HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - ENGINE ROOM RELAY BLOCK)

NG

REPLACE RELAY

5.CHECK WIRE HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - ENGINE ROOM RELAY BLOCK)
a.

Disconnect the E28 ignition or starter switch assembly connector.


b.

w/o cooling fan resister

i.

Remove the RAD relay from the engine room relay block.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
E28-6 (IG2) - RAD relay terminal 2 Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
E28-6 (IG2) or RAD relay terminal 2 - Body ground Always 10 kΩ or higher




c.

w/ cooling fan resister

i.

Remove the RAD relay and RAD No. 2 relay from the engine room relay block.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
E28-6 (IG2) - RAD relay terminal 2 Always Below 1 Ω
E28-6 (IG2) - RAD No. 2 relay terminal 2 Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
E28-6 (IG2) - Body ground Always 10 kΩ or higher
RAD relay terminal 2 - Body ground Always 10 kΩ or higher
RAD No. 2 relay terminal 2 - Body ground Always 10 kΩ or higher




Result:
Proceed to
OK
NG



OK

6.INSPECT COOLING FAN MOTOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT COOLING FAN MOTOR
a.

Inspect the cooling fan motor.

Click hereEngine / Hybrid System>3SZ-VE COOLING>COOLING FAN MOTOR>ON-VEHICLE INSPECTION

Result:
Proceed to
OK
NG




OK

7.CHECK WIRE HARNESS AND CONNECTOR (COOLING FAN MOTOR - RAD RELAY)

NG

7.CHECK WIRE HARNESS AND CONNECTOR (COOLING FAN MOTOR - RAD RELAY)
a.

Disconnect the A6 cooling fan motor connector.


b.

Remove the RAD relay from the engine room relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A6-2 - RAD relay terminal 5 Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A6-2 or RAD relay terminal 5 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.CHECK WIRE HARNESS AND CONNECTOR (RAD RELAY - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK WIRE HARNESS AND CONNECTOR (RAD RELAY - ECM)
a.

Remove the RAD relay from the engine room relay block.


b.

Disconnect the E3 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
E3-16 (FAN) - RAD relay terminal 1 Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
E3-16 (FAN) or RAD relay terminal 1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.CONFIRM VEHICLE TYPE

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR

9.CONFIRM VEHICLE TYPE
a.

Confirm the vehicle type.


Result:
Result Proceed to
w/o cooling fan resister A
w/ cooling fan resister B



A

10.CHECK WIRE HARNESS AND CONNECTOR (COOLING FAN MOTOR - BODY GROUND)

B

11.CHECK WIRE HARNESS AND CONNECTOR (COOLING FAN MOTOR - RAD NO. 2 RELAY - COOLING FAN RESISTER)
10.CHECK WIRE HARNESS AND CONNECTOR (COOLING FAN MOTOR - BODY GROUND)
a.

Disconnect the A6 cooling fan motor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A6-1 - Body ground Always Below 1 Ω



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK WIRE HARNESS AND CONNECTOR (COOLING FAN MOTOR - RAD NO. 2 RELAY - COOLING FAN RESISTER)
a.

Disconnect the A6 cooling fan motor connector.


b.

Disconnect the A12 cooling fan resister connector.


c.

Remove the RAD No. 2 relay from the engine room relay block.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A6-1 - RAD No. 2 relay terminal 5 Always Below 1 Ω
A6-1 - A12-2 (+) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A6-1 - Body ground Always 10 kΩ or higher
A12-2 (+) - Body ground Always 10 kΩ or higher
RAD No. 2 relay terminal 5 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

12.INSPECT COOLING FAN RESISTOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.INSPECT COOLING FAN RESISTOR
a.

Inspect the cooling fan resister.

Click hereEngine / Hybrid System>3SZ-VE COOLING>COOLING FAN RESISTOR>ON-VEHICLE INSPECTION

Result:
Proceed to
OK
NG




OK

13.CHECK WIRE HARNESS AND CONNECTOR (RAD NO. 2 RELAY - COOLING FAN RESISTER - BODY GROUND)

NG

REPLACE COOLING FAN RESISTOR

13.CHECK WIRE HARNESS AND CONNECTOR (RAD NO. 2 RELAY - COOLING FAN RESISTER - BODY GROUND)
a.

Remove the RAD No. 2 relay from the engine room relay block.


b.

Remove the A12 cooling fan resister connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
RAD No. 2 relay terminal 3 - Body ground Always Below 1 Ω
A12-1(-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

14.CHECK WIRE HARNESS AND CONNECTOR (RAD NO. 2 RELAY - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK WIRE HARNESS AND CONNECTOR (RAD NO. 2 RELAY - ECM)
a.

Remove the RAD No. 2 relay from the engine room relay block.


b.

Disconnect the E3 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
E3-5 (FAN2) - RAD No. 2 relay terminal 1 Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
E3-5 (FAN2) or RAD No. 2 relay terminal 1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR