Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › from 2015.08
RM19Y0E _57 Power Source / Network _003004 NETWORKING _0015181 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Main Body ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Main Body ECU Communication Stop Mode Either condition is met:
·

"Main Body" is not displayed on the CAN Bus Check screen of the GTS or Techstream

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "Main Body ECU Communication Stop Mode" in "DTC Combination Table" are output

Click here(Click here)


·

Main body ECU (fuse block assembly) branch line or connector

·

Power source circuit of main body ECU (fuse block assembly)

·

Main body ECU (fuse block assembly) ground circuit

·

Main body ECU (fuse block assembly)



WIRING DIAGRAM

C329967E01
5.24,0.802 4.76,0.25 4.76,0.25 4.594,0.25 false 1.448,5.063 3.552,5.469 2.104,0.406 10 false : CAN Main Bus Line (CANH) 1.448,5.375 3.552,5.781 2.104,0.406 10 false : CAN Main Bus Line (CANL) 4.427,5.063 6.531,5.469 2.104,0.406 10 false : CAN Branch Line (CANH) 4.438,5.375 6.542,5.781 2.104,0.406 10 false : CAN Branch Line (CANL) 0.521,2.083 1.083,2.448 0.563,0.365 10 false ECM 5.906,2.083 7.135,2.802 1.229,0.719 10 false Combination Meter Assembly 5.76,3.552 6.698,3.927 0.938,0.375 10 false Trouble Area 2.656,0.167 4.667,0.563 2.01,0.396 10 false No. 1 CAN Junction Connector 5.344,0.177 5.906,0.542 0.563,0.365 10 false DLC3 2.885,4.406 4.594,4.781 1.708,0.375 10 false Fuse Block Assembly 2.979,4 4.135,4.375 1.156,0.375 10 false Main Body ECU 0.448,3.688 1.146,4.708 0.698,1.021 10 false from No. 1 Integration Relay 1.5,3.729 1.844,4.01 0.344,0.281 10 false 3C 4.719,3.646 5.063,3.927 0.344,0.281 10 false 3G 2.615,0.833 3.115,1.156 0.5,0.323 10 false CANH 2.625,1.469 3.125,1.792 0.5,0.323 10 false CANL 2.625,3.719 2.979,3.969 0.354,0.25 10 false IG1 4.073,3.646 4.448,3.979 0.375,0.333 10 false E01 1.542,3.531 1.917,3.865 0.375,0.333 10 false 6 4.729,3.021 5.104,3.354 0.375,0.333 10 false 11 0.417,1.729 0.979,2.094 0.563,0.365 10 false 120 Ω 6.385,1.708 6.948,2.073 0.563,0.365 10 false 120 Ω 4.719,3.219 5.063,3.5 0.344,0.281 10 false 3G 4.729,3.458 5.104,3.792 0.375,0.333 10 false 12 4.063,3.219 4.438,3.552 0.375,0.333 10 false E12 2.073,0.76 2.448,1.094 0.375,0.333 10 false 21 2.073,1.396 2.448,1.729 0.375,0.333 10 false 30 4.729,0.76 5.104,1.094 0.375,0.333 10 false 17 4.729,1.396 5.104,1.729 0.375,0.333 10 false 16 3.927,0.833 4.427,1.156 0.5,0.323 10 false CANH 3.969,1.469 4.469,1.792 0.5,0.323 10 false CANL 4.719,1.594 5.063,1.875 0.344,0.281 10 false 3G 4.719,0.958 5.063,1.24 0.344,0.281 10 false 3G 2.063,0.958 2.406,1.24 0.344,0.281 10 false 3C 2.063,1.594 2.406,1.875 0.344,0.281 10 false 3C 4.063,2.792 4.438,3.125 0.375,0.333 10 false E11 4.719,2.781 5.063,3.063 0.344,0.281 10 false 3G 4.76,2.583 5.135,2.917 0.375,0.333 10 false 1 1.917,3.885 2.594,4.198 0.677,0.313 10 false ECU-IG1 1.531,2.823 1.906,3.156 0.375,0.333 10 false 1 1.49,3.01 1.833,3.292 0.344,0.281 10 false 3C 1.833,3.156 2.656,3.5 0.823,0.344 10 false BACK UP2 0.448,3.156 1.229,3.49 0.781,0.333 10 false BACK UP 2.625,3 3.167,3.26 0.542,0.26 10 false MIRB

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the ignition switch to ON, wait at least 60 seconds.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (MAIN BODY ECU (FUSE BLOCK ASSEMBLY) MAIN LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the 3C and 3G main body ECU (fuse block assembly) assembly connectors.


c.
C329970C01
1.521,2.677 1.938,2.927 0.417,0.25 1.448,0.469 1.865,0.719 0.417,0.25 2.052,1.271 2.406,0.531 2.406,0.531 2.573,0.531 true 2.052,1.521 2.333,2.063 2.333,2.063 2.5,2.063 true 1.854,3.823 2.083,4.396 2.083,4.396 2.25,4.396 true 1.729,3.823 1.479,4.375 1.479,4.375 1.313,4.375 true 0.125,0.135 0.458,0.406 0.333,0.271 10 false *a 1.635,2.719 2.052,3 0.417,0.281 10 false 3G 1.573,0.51 1.99,0.792 0.417,0.281 10 false 3C 2.302,4.313 2.938,4.573 0.635,0.26 10 false CANH 2.635,0.458 3.146,0.771 0.51,0.313 10 false CANH 2.573,1.979 3.083,2.292 0.51,0.313 10 false CANL 0.906,4.292 1.573,4.542 0.667,0.25 10 false CANL
*a Front view of wire harness connector
(to Main Body ECU (Fuse Block Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3C-21 (CANH) - 3G-17 (CANH) Cable disconnected from negative (-) battery terminal Below 1 Ω
3C-30 (CANL) - 3G-16 (CANL) Cable disconnected from negative (-) battery terminal Below 1 Ω



Result:
Result Proceed to
OK A
NG (for RHD) B
NG (for LHD) C



A

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

B

REPLACE MAIN BODY ECU (FUSE BLOCK ASSEMBLY)

C

REPLACE MAIN BODY ECU (FUSE BLOCK ASSEMBLY)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C329963C02
1.427,0.365 1.844,0.615 0.417,0.25 2.302,1.302 2.635,0.802 2.635,0.802 2.802,0.802 true 1,1.563 0.667,1.917 0.667,1.917 0.5,1.917 true 1.01,1.302 0.677,0.885 0.677,0.885 0.51,0.885 true 0.115,0.125 0.417,0.417 0.302,0.292 10 false *a 0.219,1.833 0.719,2.083 0.5,0.25 10 false E01 1.542,0.406 1.948,0.656 0.406,0.25 10 false 3G 0.219,0.802 0.719,1.052 0.5,0.25 10 false E11 2.865,0.729 3.281,0.979 0.417,0.25 10 false E12
*a Front view of wire harness connector
(to Main Body ECU (Fuse Block Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3G-1 (E11) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω
3G-11 (E12) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω
3G-12 (E01) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) battery terminal.


c.
C329964C03
1.427,0.458 1.844,0.708 0.417,0.25 1.344,1.094 1.344,0.51 1.344,0.51 1.177,0.51 true 0.552,1.094 0.552,0.26 0.552,0.26 0.719,0.26 true 0.125,0.115 0.427,0.365 0.302,0.25 10 false *a 0.927,0.438 1.302,0.688 0.375,0.25 10 false IG1 1.552,0.5 1.854,0.75 0.302,0.25 10 false 3C 0.781,0.188 1.26,0.458 0.479,0.271 10 false MIRB
*a Front view of wire harness connector
(to Main Body ECU (Fuse Block Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3C-1 (MIRB)- Body ground Always 11 to 14 V
3C-6 (IG1)- Body ground Ignition switch ON 11 to 14 V



Result:
Result Proceed to
OK (for RHD) A
OK (for LHD) B
NG C



A

REPLACE MAIN BODY ECU (FUSE BLOCK ASSEMBLY)

B

REPLACE MAIN BODY ECU (FUSE BLOCK ASSEMBLY)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)