Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › SPIRAL CABLE › 2015.08–2016.09
RM19Y0E _58 Vehicle Interior _003010 SUPPLEMENTAL RESTRAINT SYSTEMS _0015209 SPIRAL CABLE A

SUPPLEMENTAL RESTRAINT SYSTEMS  SPIRAL CABLE  INSTALLATION  


PROCEDURE

Hide 84306 1.INSTALL SPIRAL CABLE SUB-ASSEMBLY

a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS.



c.

Check that the front wheels are facing straight ahead.


d.

Attach the 3 claws to install the spiral cable sub-assembly.


e.
B263617

If installing a new spiral cable sub-assembly:

Remove the lock pin.


f.
B412680C01
2.292,3.208 2.573,3.167 false 0.719,3.25 0.833,3.156 true 0.323,3.146 0.771,3.344 0.448,0.198 10 false *1(*a) 2.094,3.125 2.542,3.323 0.448,0.198 10 false *2
*1 Lock Slider
*2 Airbag Connector (Yellow Colored)
*a Lock Position


Connect the connector to the spiral cable sub-assembly.


g.

Connect the airbag connector (yellow colored) to the spiral cable sub-assembly.

NOTICE:

When handling the airbag connector, take care not to damage the airbag wire harness.



h.

Check that the lock slider is in the lock position.


Hide 84306 2.ADJUST SPIRAL CABLE SUB-ASSEMBLY

a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:
·

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.




c.
B412681C01
2.531,1.552 2.781,1.667 2.781,1.667 2.521,1.448 true 2.802,1.583 3.042,1.792 0.24,0.208 10 false *a
*a Matchmark


Check if the spiral cable sub-assembly is centered.


d.
B412682

Rotate the spiral cable sub-assembly counterclockwise slowly by hand until it feels firm.

NOTICE:

Do not turn the spiral cable sub-assembly by the airbag wire harness.



e.
B412683C01
2.49,1.646 2.76,1.74 2.76,1.74 2.49,1.542 true 2.792,1.656 3.104,1.854 0.313,0.198 10 false *a
*a Matchmark


Rotate the spiral cable sub-assembly clockwise approximately 2.5 turns to align the matchmarks.

NOTICE:

Do not turn the spiral cable sub-assembly by the airbag wire harness.


HINT:

The spiral cable sub-assembly can be rotated approximately 2.5 turns to both the left and right from the center position.



Hide 45107 3.INSTALL HORN BUTTON WIRE SUB-ASSEMBLY (w/o Steering Pad Switch)

a.

Connect the horn button wire sub-assembly to the spiral cable assembly.


Hide 45286B 4.INSTALL UPPER STEERING COLUMN COVER

Hide 45287 5.INSTALL LOWER STEERING COLUMN COVER

Hide 45100 6.INSTALL STEERING WHEEL ASSEMBLY

Hide 7.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.


Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

Torque:
6.4 N*m (65 kgf*cm, 57 in.*lbf)

Hide 45130 10.INSPECT HORN BUTTON ASSEMBLY

a.

With the horn button assembly installed to the vehicle, perform a visual check. If there are any defects as mentioned below, replace the horn button assembly with a new one:

Cuts, minute cracks or marked discoloration on the horn button assembly top surface or in the grooved portion.


b.

Make sure that the horn sounds.

If the horn does not sound, inspect the horn system.

Click hereVehicle Exterior>HORN>HORN SYSTEM>PROBLEM SYMPTOMS TABLE