Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM › from 2015.08
RM19Y0E _59 Vehicle Exterior _003019 WIPER / WASHER _0015271 WIPER AND WASHER SYSTEM J

WIPER / WASHER  WIPER AND WASHER SYSTEM  Front Wiper Motor Circuit  


DESCRIPTION

The main body ECU (fuse block assembly) controls the windshield wiper motor assembly.

WIRING DIAGRAM

E321761E02
4.854,0.333 6.427,0.719 1.573,0.385 10 false from IG WIPER relay 1.573,3.167 2.719,3.74 1.146,0.573 10 false Windshield Wiper Motor Assembly 1.573,2.969 2.167,3.198 0.594,0.229 10 false A27 4.104,4.333 6.948,4.646 2.844,0.313 10 false Main Body ECU (Fuse Block Assembly) 3.823,1.073 4.417,1.302 0.594,0.229 10 false 12 3.875,1.521 4.469,1.75 0.594,0.229 10 false 7 3.865,1.969 4.458,2.198 0.594,0.229 10 false 8 3.865,2.406 4.458,2.635 0.594,0.229 10 false 1 3.865,3.156 4.458,3.385 0.594,0.229 10 false 1 6.208,1.271 6.802,1.5 0.594,0.229 10 false WPFU 6.198,1.729 6.792,1.958 0.594,0.229 10 false FWPP 6.208,2.177 6.802,2.406 0.594,0.229 10 false FWPH 6.198,2.615 6.792,2.844 0.594,0.229 10 false FWPL 6.208,3.375 6.802,3.604 0.594,0.229 10 false RWPG 2.604,1.26 3.198,1.49 0.594,0.229 10 false +B 2.677,1.719 3.271,1.948 0.594,0.229 10 false S 2.604,2.156 3.198,2.385 0.594,0.229 10 false HI 2.604,2.604 3.198,2.833 0.594,0.229 10 false LO 1.625,2.604 2.219,2.833 0.594,0.229 10 false E 2.885,1.177 3.479,1.406 0.594,0.229 10 false 2 2.885,1.625 3.396,1.896 0.51,0.271 10 false 1*2 2.885,2.063 3.49,2.354 0.604,0.292 10 false 3*2 2.885,2.51 3.406,2.802 0.521,0.292 10 false 5*2 1.292,2.51 1.948,2.823 0.656,0.313 10 false 4*2 3.833,1.281 4.427,1.542 0.594,0.26 10 false 3D 3.833,1.729 4.427,1.958 0.594,0.229 10 false 3D 3.833,2.167 4.427,2.396 0.594,0.229 10 false 3D 3.833,2.615 4.427,2.844 0.594,0.229 10 false 3D 3.854,3.354 4.448,3.583 0.594,0.229 10 false 3I 4.677,0.906 5.823,1.333 1.146,0.427 10 false FR WIP 1.292,2.365 1.948,2.677 0.656,0.313 10 false 5*1 2.885,1.469 3.396,1.74 0.51,0.271 10 false 3*1 2.885,1.917 3.49,2.208 0.604,0.292 10 false 4*1 2.885,2.344 3.406,2.635 0.521,0.292 10 false 1*1 0.208,4.385 1.24,4.813 1.031,0.427 10 false *1: for LHD 1.365,4.385 2.396,4.813 1.031,0.427 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS OR TECHSTREAM (FRONT WIPER MOTOR)
a.

Connect the GTS or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS or Techstream on.


d.

Enter the following menus: Body Electrical / Main Body / Active Test.


e.

Perform the Active Test according to the display on the GTS or Techstream.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Front Wiper Motor (High Speed Drive) Windshield wiper motor assembly ON or OFF -
Front Wiper Motor (Low Speed Drive) Windshield wiper motor assembly ON or OFF -

OK:

Front wiper motor operates normally.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT WINDSHIELD WIPER MOTOR ASSEMBLY
2.INSPECT WINDSHIELD WIPER MOTOR ASSEMBLY
a.

Remove the windshield wiper motor assembly.

Click hereVehicle Exterior>WIPER / WASHER>FRONT WIPER MOTOR>REMOVAL


b.

Inspect the windshield wiper motor assembly.

Click hereVehicle Exterior>WIPER / WASHER>FRONT WIPER MOTOR>INSPECTION

OK:

Windshield wiper motor assembly is normal.



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER MOTOR ASSEMBLY - MAIN BODY ECU (FUSE BLOCK ASSEMBLY) AND BODY GROUND)

NG

REPLACE WINDSHIELD WIPER MOTOR ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER MOTOR ASSEMBLY - MAIN BODY ECU (FUSE BLOCK ASSEMBLY) AND BODY GROUND)
a.

Disconnect the A27 windshield wiper motor assembly connector.


b.

Disconnect the 3D main body ECU (fuse block assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
for LHD
Tester Connection Condition Specified Condition
A27-2 (+B) - 3D-12 Always Below 1 Ω
A27-3 (S) - 3D-7 Always Below 1 Ω
A27-4 (HI) - 3D-8 Always Below 1 Ω
A27-1 (LO) - 3D-1 Always Below 1 Ω
A27-5 (E) - Body ground Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
A27-2 (+B) - 3D-12 Always Below 1 Ω
A27-1 (S) - 3D-7 Always Below 1 Ω
A27-3 (HI) - 3D-8 Always Below 1 Ω
A27-5 (LO) - 3D-1 Always Below 1 Ω
A27-4 (E) - Body ground Always Below 1 Ω


Standard Resistance (Check for Short):
for LHD
Tester Connection Condition Specified Condition
A27-2 (+B) - Body ground Always 10 kΩ or higher
A27-3 (S) - Body ground Always 10 kΩ or higher
A27-4 (HI) - Body ground Always 10 kΩ or higher
A27-1 (LO) - Body ground Always 10 kΩ or higher
3D-12 - Body ground Always 10 kΩ or higher
3D-7 - Body ground Always 10 kΩ or higher
3D-8 - Body ground Always 10 kΩ or higher
3D-1 - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
A27-2 (+B) - Body ground Always 10 kΩ or higher
A27-1 (S) - Body ground Always 10 kΩ or higher
A27-3 (HI) - Body ground Always 10 kΩ or higher
A27-5 (LO) - Body ground Always 10 kΩ or higher
3D-12 - Body ground Always 10 kΩ or higher
3D-7 - Body ground Always 10 kΩ or higher
3D-8 - Body ground Always 10 kΩ or higher
3D-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (FUSE BLOCK ASSEMBLY) - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (FUSE BLOCK ASSEMBLY) - BODY GROUND)
a.

Disconnect the 3I main body ECU (fuse block assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
3I-1 - Body ground Always Below 1 Ω



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

REPLACE MAIN BODY ECU (FUSE BLOCK ASSEMBLY)

B

REPLACE MAIN BODY ECU (FUSE BLOCK ASSEMBLY)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR